EN ISO 11833-1:2019

Plastics - Unplasticized poly(vinyl chloride) sheets - Part 1: Types, dimensions and characteristics for sheets of thickness not less than 1 mm (ISO 11833-1:2019)

This document specifies the requirements for flat extruded sheets and pressed sheets of unplasticized poly(vinyl chloride) (PVC-U) and the test methods to be used to measure the required values.
It applies only to sheets of thickness not less than 1,0 mm.
It does not cover biaxially stretched PVC-U sheets.

Kunststoffe - Weichmacherfreie Polyvinylchloridtafeln - Teil 1: Typen, Maße und Eigenschaften für Tafeln mit einer Dicke von mindestens 1 mm (ISO 11833-1:2019)

Dieses Dokument legt die Anforderungen an flache extrudierte Tafeln und gepresste Tafeln aus weichmacherfreiem Polyvinylchlorid (PVC-U) und die zum Messen der geforderten Werte anzuwendenden Prüfverfahren fest.
Die Norm gilt nur für Tafeln mit einer Dicke von mindestens 1,0 mm.
Biaxial gereckte PVC-U-Tafeln werden nicht berücksichtigt.

Plastiques - Feuilles en poly(chlorure de vinyle) non plastifié - Partie 1: Types, dimensions et caractéristiques pour des plaques d'épaisseur non inférieure à 1 mm (ISO 11833-1:2019)

Le présent document spécifie les exigences relatives aux plaques extrudées et aux plaques pressées, planes, en poly(chlorure de vinyle) non plastifié (PVC-U), ainsi que les méthodes d'essai à utiliser pour mesurer les valeurs requises.
Il est applicable uniquement aux plaques d'épaisseur au moins égale à 1,0 mm.
Il ne s'applique pas aux feuilles en PVC-U bi-étirées.

Polimerni materiali - Nemehčane polivinilkloridne plošče - 1. del: Vrste, mere in značilnosti za plošče z debelino več kot 1 mm (ISO 11833-1:2019)

Ta dokument določa zahteve za ploščate ekstrudirane plošče in stisnjene plošče iz nemehčanega polivinilklorida (PVC-U) ter preskusne metode, ki jih je treba uporabiti za merjenje zahtevanih vrednosti. Zadeva le plošče z debelino več kot 1,0 mm. Ne zajema dvoosno raztegnjenih polivinilkloridnih plošč.

General Information

• Status: Published
• Publication Date: 27-Aug-2019
• Withdrawal Date: 28-Feb-2020
• ICS: 83.140.10 - Films and sheets
• Technical Committee: CEN/TC 249 - Plastics
• Drafting Committee: CEN/TC 249 - Plastics
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 28-Aug-2019
• Completion Date: 28-Aug-2019
• Ref Project: SIST EN ISO 11833-1:2019 - Plastics - Unplasticized poly(vinyl chloride) sheets - Part 1: Types, dimensions and characteristics for sheets of thickness not less than 1 mm (ISO 11833-1:2019)

Relations

• Replaces: EN ISO 11833-1:2012 - Plastics - Unplasticized poly(vinyl chloride) sheets - Types, dimensions and characteristics - Part 1: Sheets of thickness not less than 1 mm (ISO 11833-1:2012)
• Effective Date: 08-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
01-november-2019
Nadomešča:
SIST EN ISO 11833-1:2012
Polimerni materiali - Nemehčane polivinilkloridne plošče - 1. del: Vrste, mere in
značilnosti za plošče z debelino več kot 1 mm (ISO 11833-1:2019)
Plastics - Unplasticized poly(vinyl chloride) sheets - Part 1: Types, dimensions and
characteristics for sheets of thickness not less than 1 mm (ISO 11833-1:2019)
Kunststoffe - Weichmacherfreie Polyvinylchloridtafeln - Typen, Maße und Eigenschaften
- Teil 1: Tafeln mit einer Dicke von mindestens 1 mm (ISO 11833-1:2019)
Plastiques - Feuilles en poly(chlorure de vinyle) non plastifié - Partie 1: Types,
dimensions et caractéristiques pour des plaques d'épaisseur non inférieure à 1 mm (ISO
11833-1:2019)
Ta slovenski standard je istoveten z: EN ISO 11833-1:2019
ICS:
83.140.10 Filmi in folije Films and sheets
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 11833-1
EUROPEAN STANDARD
NORME EUROPÉENNE
August 2019
EUROPÄISCHE NORM
ICS 83.140.10 Supersedes EN ISO 11833-1:2012
English Version
Plastics - Unplasticized poly(vinyl chloride) sheets - Part 1:
Types, dimensions and characteristics for sheets of
thickness not less than 1 mm (ISO 11833-1:2019)
Plastiques - Feuilles en poly(chlorure de vinyle) non Kunststoffe - Weichmacherfreie Polyvinylchloridtafeln
plastifié - Partie 1: Types, dimensions et - Teil 1: Typen, Maße und Eigenschaften für Tafeln mit
caractéristiques pour des plaques d'épaisseur non einer Dicke von mindestens 1 mm (ISO 11833-1:2019)
inférieure à 1 mm (ISO 11833-1:2019)
This European Standard was approved by CEN on 21 July 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11833-1:2019 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 11833-1:2019) has been prepared by Technical Committee ISO/TC 61 "Plastics"
in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by
NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by February 2020, and conflicting national standards
shall be withdrawn at the latest by February 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 11833-1:2012.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 11833-1:2019 has been approved by CEN as EN ISO 11833-1:2019 without any
modification.
INTERNATIONAL ISO
STANDARD 11833-1
Fourth edition
2019-07
Plastics — Unplasticized poly(vinyl
chloride) sheets —
Part 1:
Types, dimensions and
characteristics for sheets of thickness
not less than 1 mm
Plastiques — Feuilles en poly(chlorure de vinyle) non plastifié —
Partie 1: Types, dimensions et caractéristiques pour des plaques
d'épaisseur non inférieure à 1 mm
Reference number
ISO 11833-1:2019(E)
©
ISO 2019
ISO 11833-1:2019(E)
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Fax: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved

ISO 11833-1:2019(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definition . 2
4 Material . 2
5 Classification . 2
6 Requirements . 2
6.1 Masking . 2
6.2 Appearance . 2
6.3 Dimensions . 3
6.3.1 Length and width . 3
6.3.2 Rectangularity . 3
6.3.3 Thickness . 4
6.4 Basic properties . 4
6.5 Other mechanical and physical properties . 6
6.6 Chemical and physiological properties . 6
6.6.1 Flammability . 6
6.6.2 Chemical resistance . 6
6.6.3 Physiological behaviour . . 6
7 Test methods . 6
7.1 General . 6
7.1.1 Sampling. 6
7.1.2 Preparation of specimens . 6
7.1.3 Conditioning and testing of specimens . 7
7.2 Appearance examination. 7
7.3 Dimensions . 7
7.4 Mechanical properties . 8
7.4.1 Tensile stress at yield and nominal strain at break . 8
7.4.2 Modulus of elasticity in tension . 8
7.4.3 Charpy impact strength of notched specimens . 9
7.5 Thermal properties . 9
7.5.1 Vicat softening temperature . 9
7.5.2 Dimensional change on heating and resistance to delamination . 9
7.6 Total luminous transmittance .11
7.7 Other mechanical and physical properties .11
7.7.1 Charpy impact strength of unnotched specimens .11
7.7.2 Temperature of deflection under load .11
7.7.3 Creep modulus .11
7.7.4 Density .11
7.7.5 Flexural strength .12
7.7.6 Ball indentation hardness .12
7.7.7 Volume resistivity .12
8 Marking .12
Annex A (informative) Determination of resistance to delamination of thick pressed sheets
using a wedge .
...