EN 15771:2010
(Main)Vitreous and porcelain enamels - Determination of surface scratch hardness according to the Mohs scale
Vitreous and porcelain enamels - Determination of surface scratch hardness according to the Mohs scale
This European Standard specifies a method of test for determining the scratch hardness of the surface of vitreous and porcelain enamels.
Emails und Emaillierungen - Bestimmung der Ritzhärte nach Mohs
Diese Europäische Norm legt ein Prüfverfahren zur Bestimmung der Ritzhärte an Oberflächen von Email-lierungen fest.
Émaux vitrifiés - Détermination de la dureté superficielle suivant l'échelle de Mohs
La présente Norme européenne spécifie une méthode d’essai permettant de déterminer la dureté superficielle des émaux vitrifiés.
Steklasti in keramični emajli - Določevanje trdote površin na razenje po Mohsovi trdotni lestvici
Ta evropski standard opredeljuje metodo preskušanja za določanje trdote površin steklastih in keramičnih emajlov na rezanje.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Emails und Emaillierungen - Bestimmung der Ritzhärte nach MohsEmaux vitrifiés - Détermination de la dureté superficielle suivant l'échelle de MohsVitreous and porcelain enamels - Determination of scratch hardness of surface according to Mohs25.220.50Emajlne prevlekeEnamelsICS:Ta slovenski standard je istoveten z:EN 15771:2010SIST EN 15771:2010en,fr,de01-junij-2010SIST EN 15771:2010SLOVENSKI
STANDARD
SIST EN 15771:2010
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 15771
March 2010 ICS 25.220.50 English Version
Vitreous and porcelain enamels - Determination of surface scratch hardness according to the Mohs scale
Émaux vitrifiés - Détermination de la dureté superficielle suivant l'échelle de Mohs
Emails und Emaillierungen - Bestimmung der Ritzhärte nach Mohs This European Standard was approved by CEN on 13 February 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 15771:2010: ESIST EN 15771:2010
EN 15771:2010 (E) 2 Contents Page Foreword .31Scope .42Normative references .43Terms and definitions .44Principle .45Reference minerals .46Test specimen .57Procedure .58Assessment of result .59Test report .5 SIST EN 15771:2010
EN 15771:2010 (E) 3 Foreword This document (EN 15771:2010) has been prepared by Technical Committee CEN/TC 262 “Metallic and other inorganic coatings”, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2010, and conflicting national standards shall be withdrawn at the latest by September 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. SIST EN 1
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.