EN 10217-1:2019/FprA1
(Amendment)Welded steel tubes for pressure purposes - Technical delivery conditions - Part 1: Electric welded and submerged arc welded non-alloy steel tubes with specified room temperature properties
Welded steel tubes for pressure purposes - Technical delivery conditions - Part 1: Electric welded and submerged arc welded non-alloy steel tubes with specified room temperature properties
This document specifies the technical delivery conditions for qualities TR1 and TR2 of electric welded and submerged arc welded tubes of circular cross section, with specified room temperature properties, made from non-alloy quality steel.
NOTE 1 Quality TR2 is intended to support the essential requirements of EU Directive 2014/68/EU in respect of pressure equipment with specified room temperature properties (see Table 5).
NOTE 2 Once this standard is published in the Official Journal of the European Union (OJEU), presumption of conformity to the Essential Safety Requirements (ESR) of Directive 2014/68/EU is limited to the technical data for the materials in this standard and does not presume adequacy of the material for a specific item of pressure equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of a specific item of equipment to verify that the ESRs of the Pressure Equipment Directive are satisfied, needs to be done by the designer or manufacturer of the pressure equipment, taking also into account any subsequent processing procedures which may affect properties of the base materials.
Geschweißte Stahlrohre für Druckbeanspruchungen - Technische Lieferbedingungen - Teil 1: Elektrisch geschweißte und unterpulvergeschweißte Rohre aus unlegierten Stählen mit festgelegten Eigenschaften bei Raumtemperatur
Tubes soudés en acier pour service sous pression - Conditions techniques de livraison - Partie 1 : Tubes en acier non allié, soudés électrique et soudés à l'arc sous flux, avec caractéristiques spécifiées à température ambiante
Varjene jeklene cevi za tlačne posode - Tehnični dobavni pogoji - 1. del: Električno varjene in obločno pod praškom varjene nelegirane jeklene cevi s specificiranimi lastnostmi za delo pri sobni temperaturi - Dopolnilo A1
General Information
Relations
Overview
EN 10217-1:2019/FprA1 specifies technical delivery conditions for electric welded and submerged arc welded (SAW) non-alloy steel tubes of circular cross section with specified room temperature properties. It covers two material qualities, TR1 and TR2, intended for tubes used for pressure purposes (e.g., components of pressure equipment). The draft amendment A1 updates normative references, modifies manufacturing route allowances, and deletes Annex B.
Key topics and requirements
- Scope and materials
- Applies to welded tubes made from non-alloy quality steel with defined mechanical properties at room temperature.
- Covers qualities TR1 and TR2; TR2 is intended to support compliance with the EU Pressure Equipment Directive (2014/68/EU) for materials with specified room temperature properties.
- Manufacturing routes and weld types
- Addresses production by electric welding and submerged arc welding for circular tubes.
- Amendment A1: for manufacturing routes 1a–1d, cold‑rolled strip is permitted for small wall thicknesses up to 2 mm.
- Technical delivery conditions
- Defines requirements for testing, inspection and documentation to be supplied with tubes (material properties at room temperature, test reports, etc.).
- Non‑destructive and mechanical testing
- References updated NDT and test standards (EN ISO 10893 series for automated electromagnetic, eddy current, ultrasonic and radiographic testing; EN ISO 6892-1 for tensile testing at room temperature).
- Conformity and design responsibility
- When published in the OJEU, the standard gives a presumption of conformity to ESRs of the Pressure Equipment Directive only for the material technical data. It does not guarantee suitability for a specific equipment item - designers/manufacturers must verify material data against their design and post‑processing effects.
Practical applications
- Use cases:
- Pressure vessels, boilers, heat exchangers, piping and hydraulic systems where welded tubes with defined room temperature properties are required.
- Who uses it:
- Tube manufacturers, material suppliers, pressure equipment designers, fabricators, inspection bodies and procurement specialists.
- Benefits:
- Ensures consistent material quality, traceable testing, and harmonised delivery conditions across EU markets - aiding specification, compliance assessment and procurement.
Related standards
- EN ISO 6892-1 - Tensile testing at room temperature
- EN ISO 10893 (parts 1,2,3,6,7,10,11) - Non‑destructive testing for steel tubes
- EU Pressure Equipment Directive 2014/68/EU - Essential Safety Requirements (material verification responsibilities)
Keywords: EN 10217-1:2019/FprA1, welded steel tubes, electric welded, submerged arc welded, TR1, TR2, pressure purposes, non‑alloy steel tubes, Pressure Equipment Directive, EN ISO 10893, EN ISO 6892-1.
Standards Content (Sample)
SLOVENSKI STANDARD
01-marec-2023
Varjene jeklene cevi za tlačne posode - Tehnični dobavni pogoji - 1. del: Električno
varjene in obločno pod praškom varjene nelegirane jeklene cevi s specificiranimi
lastnostmi za delo pri sobni temperaturi - Dopolnilo A1
Welded steel tubes for pressure purposes - Technical delivery conditions - Part 1:
Electric welded and submerged arc welded non-alloy steel tubes with specified room
temperature properties
Geschweißte Stahlrohre für Druckbeanspruchungen - Technische Lieferbedingungen -
Teil 1: Elektrisch geschweißte und unterpulvergeschweißte Rohre aus unlegierten
Stählen mit festgelegten Eigenschaften bei Raumtemperatur
Tubes soudés en acier pour service sous pression - Conditions techniques de livraison -
Partie 1 : Tubes en acier non allié, soudés électriquement et soudés à l'arc immergé,
avec caractéristiques spécifiées à température ambiante
Ta slovenski standard je istoveten z: EN 10217-1:2019/prA1
ICS:
23.020.32 Tlačne posode Pressure vessels
77.140.75 Jeklene cevi in cevni profili Steel pipes and tubes for
za posebne namene specific use
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT
EUROPEAN STANDARD
EN 10217-1:2019
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
January 2023
ICS 23.040.10; 77.140.75
English Version
Welded steel tubes for pressure purposes - Technical
delivery conditions - Part 1: Electric welded and
submerged arc welded non-alloy steel tubes with specified
room temperature properties
Tubes soudés en acier pour service sous pression - Geschweißte Stahlrohre für Druckbeanspruchungen -
Conditions techniques de livraison - Partie 1 : Tubes en Technische Lieferbedingungen - Teil 1: Elektrisch
acier non allié, soudés électriquement et soudés à l'arc geschweißte und unterpulvergeschweißte Rohre aus
immergé, avec caractéristiques spécifiées à unlegierten Stählen mit festgelegten Eigenschaften bei
température ambiante Raumtemperatur
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC
459/SC 10.
This draft amendment A1, if approved, will modify the European Standard EN 10217-1:2019. If this draft becomes an
amendment, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for
inclusion of this amendment into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 10217-1:2019/prA1:2023 E
worldwide for CEN national Members.
EN 10217-1:2019/prA1:2023 (E)
Contents Page
European foreword .
...
Frequently Asked Questions
EN 10217-1:2019/FprA1 is a draft published by the European Committee for Standardization (CEN). Its full title is "Welded steel tubes for pressure purposes - Technical delivery conditions - Part 1: Electric welded and submerged arc welded non-alloy steel tubes with specified room temperature properties". This standard covers: This document specifies the technical delivery conditions for qualities TR1 and TR2 of electric welded and submerged arc welded tubes of circular cross section, with specified room temperature properties, made from non-alloy quality steel. NOTE 1 Quality TR2 is intended to support the essential requirements of EU Directive 2014/68/EU in respect of pressure equipment with specified room temperature properties (see Table 5). NOTE 2 Once this standard is published in the Official Journal of the European Union (OJEU), presumption of conformity to the Essential Safety Requirements (ESR) of Directive 2014/68/EU is limited to the technical data for the materials in this standard and does not presume adequacy of the material for a specific item of pressure equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of a specific item of equipment to verify that the ESRs of the Pressure Equipment Directive are satisfied, needs to be done by the designer or manufacturer of the pressure equipment, taking also into account any subsequent processing procedures which may affect properties of the base materials.
This document specifies the technical delivery conditions for qualities TR1 and TR2 of electric welded and submerged arc welded tubes of circular cross section, with specified room temperature properties, made from non-alloy quality steel. NOTE 1 Quality TR2 is intended to support the essential requirements of EU Directive 2014/68/EU in respect of pressure equipment with specified room temperature properties (see Table 5). NOTE 2 Once this standard is published in the Official Journal of the European Union (OJEU), presumption of conformity to the Essential Safety Requirements (ESR) of Directive 2014/68/EU is limited to the technical data for the materials in this standard and does not presume adequacy of the material for a specific item of pressure equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of a specific item of equipment to verify that the ESRs of the Pressure Equipment Directive are satisfied, needs to be done by the designer or manufacturer of the pressure equipment, taking also into account any subsequent processing procedures which may affect properties of the base materials.
EN 10217-1:2019/FprA1 is classified under the following ICS (International Classification for Standards) categories: 23.040.10 - Iron and steel pipes; 77.140.75 - Steel pipes and tubes for specific use. The ICS classification helps identify the subject area and facilitates finding related standards.
EN 10217-1:2019/FprA1 has the following relationships with other standards: It is inter standard links to EN 10217-1:2019. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
EN 10217-1:2019/FprA1 is associated with the following European legislation: EU Directives/Regulations: 2014/68/EU; Standardization Mandates: M/071, M/601. When a standard is cited in the Official Journal of the European Union, products manufactured in conformity with it benefit from a presumption of conformity with the essential requirements of the corresponding EU directive or regulation.
You can purchase EN 10217-1:2019/FprA1 directly from iTeh Standards. The document is available in PDF format and is delivered instantly after payment. Add the standard to your cart and complete the secure checkout process. iTeh Standards is an authorized distributor of CEN standards.
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...