EN 10216-2:2024

Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 2: Non-alloy and alloy steel tubes with specified elevated temperature properties

This document specifies the technical delivery conditions in two test categories for seamless tubes of circular cross section, with specified elevated temperature properties, made of non-alloy and alloy steel.
This Part of EN 10216 is also be applied for tubes of non-circular cross section; necessary modification will be agreed at the time of enquiry and order.

Nahtlose Stahlrohre für Druckbeanspruchungen - Technische Lieferbedingungen - Teil 2: Rohre aus unlegierten und legierten Stählen mit festgelegten Eigenschaften bei erhöhten Temperaturen

Dieses Dokument enthält die technischen Lieferbedingungen für nahtlose Rohre mit kreisförmigem Querschnitt aus unlegiertem und legiertem Stahl mit festgelegten Eigenschaften bei erhöhten Temperaturen und legt dafür zwei Prüfkategorien fest.
Dieser Teil der EN 10216 kann auch für Rohre mit nichtkreisförmigem Querschnitt angewendet werden; notwendige Anpassungen sollten bei der Anfrage und Bestellung vereinbart werden.
ANMERKUNG   Nach Veröffentlichung dieses Dokumentes im EU Amtsblatt (OJEU) unter der Richtlinie 2014/68/EU, Druckgeräterichtlinie, ist die Annahme ihrer Konformität mit den grundlegenden Anforderungen (ESR) der Richtlinie 2014/68/EU auf die technischen Daten von Werkstoffen in diesem Dokument beschränkt, und es darf nicht angenommen werden, dass damit die Eignung des Werkstoffs für ein bestimmtes Ausrüstungsteil festgestellt ist. Folglich müssen die in dieser Werkstoffnorm angegebenen technischen Parameter im Hinblick auf die konstruktiven Anforderungen dieses bestimmten Ausrüstungsteils ermittelt werden, um damit zu verifizieren, dass den ESR der Druckgeräterichtlinie entsprochen wird. Dies muss durch den Ausleger der Druckgeräte geschehen, der auch den nachfolgenden Herstellungsprozess berücksichtigen muss, der die Eigenschaften des Grundmaterials verändern könnte.

Tubes sans soudure en acier pour service sous pression - Conditions techniques de livraison - Partie 2: Tubes en acier non allié et allié avec caractéristiques spécifiées à température élevée

Le présent document spécifie les conditions techniques de livraison, selon deux catégories d'essai, pour les tubes sans soudure à section circulaire en acier non allié et allié, avec caractéristiques spécifiées à température élevée.
La présente partie de l'EN 10216 est également applicable aux tubes de section non circulaire ; les modifications nécessaires feront l'objet d'un accord lors de l'appel d'offres et de la commande.

Nevarjene jeklene cevi za tlačne posode - Tehnični dobavni pogoji - 2. del: Nelegirane in legirane jeklene cevi s specificiranimi lastnostmi za delo pri povišanih temperaturah

General Information

• Status: Not Published
• Publication Date: 31-Dec-2024
• ICS: 23.040.10 - Iron and steel pipes
• ICS: 77.140.75 - Steel pipes and tubes for specific use
• Technical Committee: ECISS/TC 110 - Steel tubes, and iron and steel fittings
• Drafting Committee: ECISS/TC 110/WG 1 - Tubes for pressure purposes
• Current Stage: 6055 - CEN Ratification completed (DOR) - Publishing
• Start Date: 13-Oct-2024
• Due Date: 25-Feb-2025
• Completion Date: 13-Oct-2024
• Directive: 2014/68/EU - Directive 2014/68/EU of the European Parliament and of the Council of 15 May 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of pressure equipment
• Mandate: M/071 - Mandate to CEN for standardization in the field of Pressure equipment
• Mandate: M/601 - COMMISSION IMPLEMENTING DECISION of 1.3.2024 on a standardisation request to the European Committee for Standardization and the European Committee for Electrotechnical Standardization as regards pressure equipment and assemblies in support of Directive 2014/68/EU of the European Parliament and of the Council
• Ref Project: kSIST FprEN 10216-2:2024 - Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 2: Non-alloy and alloy steel tubes with specified elevated temperature properties

Relations

• Revises: EN 10216-2:2013+A1:2019 - Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 2: Non-alloy and alloy steel tubes with specified elevated temperature properties
• Effective Date: 18-Jan-2023

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN 10216-2:2023
01-junij-2023
Nevarjene jeklene cevi za tlačne posode - Tehnični dobavni pogoji - 2. del:
Nelegirane in legirane jeklene cevi s specificiranimi lastnostmi za delo pri
povišanih temperaturah
Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 2:
Non-alloy and alloy steel tubes with specified elevated temperature properties
Nahtlose Stahlrohre für Druckbeanspruchungen - Technische Lieferbedingungen - Teil 2:
Rohre aus unlegierten und legierten Stählen mit festgelegten Eigenschaften bei erhöhten
Temperaturen
Tubes sans soudure en acier pour service sous pression - Conditions techniques de
livraison - Partie 2: Tubes en acier non allié et allié avec caractéristiques spécifiées à
température élevée
Ta slovenski standard je istoveten z: prEN 10216-2
ICS:
23.020.32 Tlačne posode Pressure vessels
77.140.75 Jeklene cevi in cevni profili Steel pipes and tubes for
za posebne namene specific use
oSIST prEN 10216-2:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

oSIST prEN 10216-2:2023
oSIST prEN 10216-2:2023
DRAFT
EUROPEAN STANDARD
prEN 10216-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2023
ICS 23.040.10; 77.140.75 Will supersede EN 10216-2:2013+A1:2019
English Version
Seamless steel tubes for pressure purposes - Technical
delivery conditions - Part 2: Non-alloy and alloy steel tubes
with specified elevated temperature properties
Tubes sans soudure en acier pour service sous Nahtlose Stahlrohre für Druckbeanspruchungen -
pression - Conditions techniques de livraison - Partie 2: Technische Lieferbedingungen - Teil 2: Rohre aus
Tubes en acier non allié et allié avec caractéristiques unlegierten und legierten Stählen mit festgelegten
spécifiées à température élevée Eigenschaften bei erhöhten Temperaturen
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 459/SC 10.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 10216-2:2023 E
worldwide for CEN national Members.

oSIST prEN 10216-2:2023
prEN 10216-2:2023 (E)
Contents Page
European foreword . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 6
4 Symbols . 7
5 Classification and designation . 7
5.1 Classification . 7
5.2 Designation. 7
6 Information to be supplied by the purchaser . 8
6.1 Mandatory information . 8
6.2 Options . 8
6.3 Examples of an order . 9
7 Manufacturing process . 9
7.1 Steel making process . 9
7.2 Tube manufacture and delivery conditions . 9
8 Requirements . 11
8.1 General . 11
8.2 Chemical composition . 11
8.3 Mechanical properties . 16
8.4 Appearance and internal soundness. 21
8.5 Straightness . 21
8.6 Preparation of ends . 21
8.7 Dimensions, masses and tolerances . 22
9 Inspection . 29
9.1 Types of inspection . 29
9.2 Inspection documents . 29
9.3 Summary of inspection and verification testing . 29
10 Sampling . 31
10.1 Frequency of tests . 31
10.2 Preparation of samples and test pieces . 32
11 Verification test methods . 33
11.1 Chemical analysis . 33
11.2 Tensile test . 33
11.3 Flattening test . 33
11.4 Ring tensile test . 35
11.5 Drift expanding test . 35
11.6 Ring expanding test . 37
11.7 Impact test . 37
11.8 Leak tightness test . 38
11.9 Dimensional inspection . 38
11.10 Visual examination . 38
oSIST prEN 10216-2:2023
prEN 10216-2:2023 (E)
11.11 Non-destructive testing .38
11.12 Material identification .39
11.13 Retests, sorting and reprocessing .39
12 Marking .39
12.1 Marking to be applied .39
12.2 Additional marking .40
13 Protection .40
Annex A (informative) Creep rupture strength values .41
Annex B (informative) Technical changes from the previous edition .51
B.1 Introduction .51
B.2 Technical changes .51
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of Directive 2014/68/EU aimed to be covered .52
Bibliography .53

oSIST prEN 10216-2:2023
prEN 10216-2:2023 (E)
European foreword
This document (prEN 10216-2:2023) has been prepared by Technical Committee CEN/TC 459 “ECISS –
European Committee for Iron and Steel Standardization” , the secretariat of which is held by AFNOR.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 10216-2:2013+A1:2020.
For the list of the most significant technical changes that were made in prEN 10216-2:2023, see Annex B.
This document has been prepared under a Standardization Request given to CEN by the European
Commission and the European Free Trade Association, and supports essential requirements of
EU Directive(s) / Regulation(s).
For relationship with EU Directive(s) / Regulation(s), see informative Annex ZA, which is an integral part
of this document.
EN 10216 consists of the following parts, under the general title "Seamless steel tubes for pressure
purposes – Technical delivery conditions":
— Part 1: Non-alloy steel tubes with specified room temperature properties
— Part 2: Non-alloy and alloy steel tubes with specified elevated temperature properties (the present
document)
— Part 3: Alloy fine grain steel tubes
— Part 4: Non-alloy and alloy steel tubes with specified low temperature properties
— Part 5: Stainless steel tubes
Another European Standard series covering tubes for pressure purposes is:
EN 10217 series, Welded steel tubes for pressure purposes – Technical delivery conditions

Through its sub-committee SC 10 “Steel tubes, and iron and steel fittings” (secretariat: UNI).
oSIST prEN 10216-2:2023
prEN 10216-2:2023 (E)
1 Scope
This document specifies the technical delivery conditions in two test categories for seamless tubes of
circular cross section, with specified elevated temperature properties, made of non-alloy and alloy
steel.
This Part of EN 10216 can also be applied for tubes of non-circular cross section; necessary modification
will be
...