EN 930:1997/A1:2004

Footwear, leather and imitation leather goods manufacturing machines - Roughing, scouring, polishing and trimming machines - Safety requirements

This standard applies to the following machines which are intended to work material for the manufacture of footwear:
   - automatic and manual roughing, scouring and polishing machines
   - automatic and manual edge contour trimming machines
1.2 This standard does not apply to modular shoe repair machines.
1.3 This standard specifies safety requirements for design, construction and operation.
It takes account of intended use, foreseeable misuse, component and system failure.
1.4 This standard covers all hazards relevant to the footwear, leather and imitation leather goods manufacturing industries.
The use of machines within the scope of this standard in different industries may give rise to hazards which were not taken into account at the time of its preparation.
1.5 This standard applies to machines manufactured after its date of issue.

Maschinen zur Herstellung von Schuhen, Leder- und Kunstlederwaren - Aufrau-, Ausglas- Polier- und Kantenbearbeitungsmachinen - Sicherheitsanforderungen

Machines pour la fabrication de chaussures et d'articles en cuir et matériaux similaires - Machines à carder, à verrer, à polir et à fraiser - Prescriptions de sécurité

Le présent code d'essai acoustique complète l'EN 12545 dans la détermination et la déclaration de l'émission sonore des machines à carder et à verrer. L'EN 12545 et la présente Annexe doivent toujours être utilisées conjointement.

Stroji za izdelavo obutve ter izdelkov iz usnja in njegovih imitacij – Stroji za grobo obdelavo, brušenje, loščenje in robljenje – Varnostne zahteve

General Information

• Status: Withdrawn
• Publication Date: 26-Oct-2004
• Withdrawal Date: 11-Aug-2009
• ICS: 59.140.40 - Machines and equipment for leather and fur production
• ICS: 61.060 - Footwear
• Technical Committee: CEN/TC 201 - Leather and imitation leather goods and footwear manufacturing machinery - Safety
• Drafting Committee: CEN/TC 201 - Leather and imitation leather goods and footwear manufacturing machinery - Safety
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 12-Aug-2009
• Completion Date: 12-Aug-2009
• Directive: 98/37/EC - Machinery
• Mandate: M/079 - Mandate to CEN and CENELEC for standardization in the field of machines
• Ref Project: SIST EN 930:2000/A1:2005 - Footwear, leather and imitation leather goods manufacturing machines - Roughing, scouring, polishing and trimming machines - Safety requirements

Relations

• Merged Into: EN 930:1997+A2:2009 - Footwear, leather and imitation leather goods manufacturing machines - Roughing, scouring, polishing and trimming machines - Safety requirements
• Effective Date: 19-Jan-2023
• Amends: EN 930:1997 - Footwear, leather and imitation leather goods manufacturing machines - Roughing, scouring, polishing and trimming machines - Safety requirements
• Effective Date: 22-Dec-2008

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 930:2000/A1:2005
01-marec-2005
6WURML]DL]GHODYRREXWYHWHUL]GHONRYL]XVQMDLQQMHJRYLKLPLWDFLM±6WURML]DJURER
REGHODYREUXãHQMHORãþHQMHLQUREOMHQMH±9DUQRVWQH]DKWHYH
Footwear, leather and imitation leather goods manufacturing machines - Roughing,
scouring, polishing and trimming machines - Safety requirements
Maschinen zur Herstellung von Schuhen, Leder- und Kunstlederwaren - Aufrau-, Ausglas
- Polier- und Kantenbearbeitungsmachinen - Sicherheitsanforderungen
Machines pour la fabrication de chaussures et d'articles en cuir et matériaux similaires -
Machines a carder, a verrer, a polir et a fraiser - Prescriptions de sécurité
Ta slovenski standard je istoveten z: EN 930:1997/A1:2004
ICS:
59.140.40 Stroji in oprema za Machines and equipment for
proizvodnjo usnja in krzna leather and fur production
61.060 Obuvala Footwear
SIST EN 930:2000/A1:2005 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

EUROPEAN STANDARD
EN 930:1997/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2004
ICS 59.140.40; 61.060
English version
Footwear, leather and imitation leather goods manufacturing
machines - Roughing, scouring, polishing and trimming
machines - Safety requirements
Machines pour la fabrication de chaussures et articles en Schuhmaschinenwaren, Leder- und
cuir et similicuir - Machines à carder, verrer, polir et fraiser - Kunstlederwarenmaschinen - Aufrauh-, Ausglas- und
Exigences de sécurité Kantenbearbeitungsmachinen - Sicherheitsanforderungen
This amendment A1 modifies the European Standard EN 930:1997; it was approved by CEN on 16 August 2004.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references concerning such
national standards may be obtained on application to the Central Secretariat or to any CEN member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 930:1997/A1:2004: E
worldwide for CEN national Members.

---------------------- Page: 2 ----------------------

EN 930:1997/A1:2004 (E)
Foreword
This document (EN 930:1997/A1:2004) has been prepared by Technical Committee CEN/TC 201 “Leather
and imitation leather goods and footwear manufacturing machinery - Safety”, the secretariat of which is held
by UNI.
This Amendment to the European Standard EN 930:1997 shall be given the status of a national standard,
either by publication of an identical text or by endorsement, at the latest by April 2005, and conflicting national
standards shall be withdrawn at the latest by April 2005.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA of EN 930:1997.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland
and United Kingdom.
2

---------------------- Page: 3 ----------------------

EN 930:1997/A1:2004 (E)
Annex E
(normative)

Noise Test Code for roughing and scouring machines
E.1 Scope
This noise test code complements EN 12545 for the determination and declaration of the noise emission from
roughing and scouring machines. EN 12545 and this Annex shall always be used jointly.
E.2 Normative references
See EN 12545:2000, Clause 2.
E.3 Definitions
E.3.1 Test Tool
An abrasive band or pad, for roughing and scouring footwear components, mounted on a wheel or on a belt,
of specified material, dimensions and form.
E.3.2 Test Workpiece
For shoe upper roughing and scouring machines, a shoe upper, together with insole
...