EN 15085-3:2022
(Main)Railway applications - Welding of railway vehicles and components - Part 3: Design requirements
Railway applications - Welding of railway vehicles and components - Part 3: Design requirements
This document applies to welding of metallic materials in the manufacture and maintenance of railway vehicles and their components.
This document specifies applicable design and classification rules.
This document does not define parameters for the dimensioning.
NOTE Requirements on structures can be found in other standards like EN 12663.
Bahnanwendungen - Schweißen von Schienenfahrzeugen und -fahrzeugteilen - Teil 3: Konstruktionsvorgaben
Dieses Dokument gilt für das Schweißen metallischer Werkstoffe bei der Herstellung und Instandsetzung von Schienenfahrzeugen und fahrzeugteilen.
Dieses Dokument legt anwendbare Konstruktions- und Klassifizierungsregeln fest.
Dieses Dokument legt keine Parameter für die Dimensionierung fest.
ANMERKUNG Anforderungen an Strukturen finden sich in anderen Normen (z. B. EN 12663).
Applications ferroviaires - Soudage des véhicules ferroviaires et des pièces - Partie 3 : Exigences de conception
Le présent document s'applique au soudage de matériaux métalliques réalisé dans le cadre de la fabrication et de la maintenance des véhicules et des composants ferroviaires.
Le présent document spécifie les règles de conception et de classification applicables.
Le présent document ne spécifie pas les paramètres de dimensionnement.
NOTE Les exigences relatives aux structures peuvent être trouvées dans d'autres normes (par exemple, l'EN 12663).
Železniške naprave - Varjenje železniških vozil in elementov - 3. del: Zahteve za projektiranje
Ta dokument se uporablja za varjenje kovinskih materialov pri izdelavi in vzdrževanju železniških vozil ter njihovih elementov.
Dokument določa zahteve za projektiranje in pravila za klasifikacijo.
Ta dokument ne določa parametrov za dimenzioniranje.
OPOMBA: Zahteve za konstrukcije je mogoče najti v drugih standardih, kot je EN 12663.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 15085-3:2023
01-januar-2023
Nadomešča:
SIST EN 15085-3:2008
SIST EN 15085-3:2008/AC:2010
Železniške naprave - Varjenje železniških vozil in elementov - 3. del: Zahteve za
projektiranje
Railway applications - Welding of railway vehicles and components - Part 3: Design
requirements
Bahnanwendungen - Schweißen von Schienenfahrzeugen und -fahrzeugteilen - Teil 3:
Konstruktionsvorgaben
Applications ferroviaires - Soudage des véhicules et des composants ferroviaires - Partie
3 : Exigences de conception
Ta slovenski standard je istoveten z: EN 15085-3:2022
ICS:
25.160.10 Varilni postopki in varjenje Welding processes
45.060.01 Železniška vozila na splošno Railway rolling stock in
general
SIST EN 15085-3:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 15085-3:2023
---------------------- Page: 2 ----------------------
SIST EN 15085-3:2023
EN 15085-3
EUROPEAN STANDARD
NORME EUROPÉENNE
November 2022
EUROPÄISCHE NORM
ICS 25.160.10; 45.060.01 Supersedes EN 15085-3:2007
English Version
Railway applications - Welding of railway vehicles and
components - Part 3: Design requirements
Applications ferroviaires - Soudage des véhicules Bahnanwendungen - Schweißen von
ferroviaires et des pièces - Partie 3 : Exigences de Schienenfahrzeugen und -fahrzeugteilen - Teil 3:
conception Konstruktionsvorgaben
This European Standard was approved by CEN on 5 September 2022.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 15085-3:2022 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 15085-3:2023
EN 15085-3:2022 (E)
Contents
European foreword . 4
Introduction . 6
1 Scope . 7
2 Normative references . 7
3 Terms and definitions . 9
4 Design requirements . 9
4.1 General. 9
4.2 Dimensioning of welded joints . 10
4.3 Stress categories and stress factors . 10
4.4 Safety categories . 10
4.5 Weld performance classes . 10
4.6 Weld inspection classes . 11
5 Quality levels for imperfections .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.