EN ISO 18274:2010
(Main)Welding consumables - Solid wire electrodes, solid strip electrodes, solid wires and solid rods for fusion welding of nickel and nickel alloys - Classification (ISO 18274:2010)
Welding consumables - Solid wire electrodes, solid strip electrodes, solid wires and solid rods for fusion welding of nickel and nickel alloys - Classification (ISO 18274:2010)
ISO 18274:2010 specifies requirements for classification of solid wire electrodes, solid strip electrodes or solid rods for fusion welding of nickel and nickel alloys. The classification of the solid wire electrodes, solid strip electrodes or solid rods is based on their chemical composition.
Schweißzusätze - Draht- und Bandelektroden, Massivdrähte und -stäbe zum Schmelzschweißen von Nickel und Nickellegierungen - Einteilung (ISO 18274:2010)
Diese Internationale Norm legt Anforderungen für die Einteilung von Drahtelektroden, Bandelektroden,
Massivdrähten und Massivstäben zum Schmelzschweißen von Nickel und Nickellegierungen fest. Die
Einteilung der Drahtelektroden, Bandelektroden, Massivdrähte und Massivstäbe erfolgt nach ihrer chemischen
Zusammensetzung.
Produits consommables pour le soudage - Fils-électrodes pleins, feuillards pleins, fils pleins et baguettes pleines pour le soudage par fusion du nickel et des alliages de nickel - Classification (ISO 18274:2010)
L'ISO 18274:2010 spécifie les exigences de classification des fils-électrodes pleins, feuillards pleins, fils pleins et baguettes pleines pour le soudage par fusion du nickel et des alliages de nickel. La classification des fils-électrodes pleins, feuillards pleins, fils pleins et baguettes pleines est basée sur leur composition chimique.
Dodajni materiali za varjenje - Žične in tračne elektrode, žice in palice za talilno varjenje niklja in nikljevih zlitin - Razvrstitev (ISO 18274:2010)
Ta mednarodni standard določa zahteve za razvrščanje žičnih elektrod, tračnih elektrod, žic in palic za talilno varjenje niklja in nikljevih zlitin. Razvrščanje žičnih elektrod, tračnih elektrod, žic in palic temelji na njihovi kemični sestavi.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-januar-2012
1DGRPHãþD
SIST EN ISO 18274:2004
SIST EN ISO 18274:2004/AC:2007
'RGDMQLPDWHULDOL]DYDUMHQMHäLþQHLQWUDþQHHOHNWURGHåLFHLQSDOLFH]DWDOLOQR
YDUMHQMHQLNOMDLQQLNOMHYLK]OLWLQ5D]YUVWLWHY ,62
Welding consumables - Wire and strip electrodes, wires and rods for fusion welding of
nickel and nickel alloys - Classification (ISO 18274:2010)
Schweißzusätze - Draht- und Bandelektroden, Massivdrähte und -stäbe zum
Schmelzschweißen von Nickel und Nickellegierungen - Einteilung (ISO 18274:2010)
Produits consommables pour le soudage - Fils-électrodes et feuillards, fils et baguettes
pour le soudage par fusion du nickel et des alliages de nickel - Classification (ISO
18274:2010)
Ta slovenski standard je istoveten z: EN ISO 18274:2010
ICS:
25.160.20 Potrošni material pri varjenju Welding consumables
77.120.40 Nikelj, krom in njune zlitine Nickel, chromium and their
alloys
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 18274
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2010
ICS 25.160.20 Supersedes EN ISO 18274:2004
English Version
Welding consumables - Solid wire electrodes, solid strip
electrodes, solid wires and solid rods for fusion welding of nickel
and nickel alloys - Classification (ISO 18274:2010)
Produits consommables pour le soudage - Fils-électrodes Schweißzusätze - Draht- und Bandelektroden,
pleins, feuillards pleins, fils pleins et baguettes pleines pour Massivdrähte und -stäbe zum Schmelzschweißen von
le soudage par fusion du nickel et des alliages de nickel - Nickel und Nickellegierungen - Einteilung (ISO 18274:2010)
Classification (ISO 18274:2010)
This European Standard was approved by CEN on 14 December 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 18274:2010: E
worldwide for CEN national Members.
Contents Page
Foreword .3
Foreword
This document (EN ISO 18274:2010) has been prepared by Technical Committee ISO/TC 44 "Welding and
allied processes" in collaboration with Technical Committee CEN/TC 121 “Welding” the secretariat of which is
held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by June 2011, and conflicting national standards shall be withdrawn at
the latest by June 2011.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 18274:2004.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 18274:2010 has been approved by CEN as a EN ISO 18274:2010 without any modification.
INTERNATIONAL ISO
STANDARD 18274
Second edition
2010-12-15
Welding consumables — Solid wire
electrodes, solid strip electrodes, solid
wires and solid rods for fusion welding of
nickel and nickel alloys — Classification
Produits consommables pour le soudage — Fils-électrodes pleins,
feuillards pleins, fils pleins et baguettes pleines pour le soudage
par fusion du nickel et des alliages de nickel — Classification
Reference number
ISO 18274:2010(E)
©
ISO 2010
ISO 18274:2010(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2010
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2010 – All rights reserved
ISO 18274:2010(E)
Contents Page
Foreword .iv
Introduction.v
1 Scope.1
2 Normative references.1
3 Classification .1
4 Symbols and requirements .1
4.1 Symbols for the product form.1
4.2 Symbol for the chemical composition .2
5 Mechanical properties of the weld metal .9
6 Chemical analysis .9
7 Rounding procedure .9
8 Retest.9
9 Technical delivery conditions .9
10 Designation .9
Annex A (informative) Description of consumables classes .11
Annex B (informative) System for designation of welding filler metals.18
Annex C (informative) Corresponding national classifications and typical weld metal tensile
strengths .19
Bibliography.24
ISO 18274:2010(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 18274 was prepared by Technical Committee ISO/TC 44, Welding and allied processes, Subcommittee
SC 3, Welding consumables.
This second edition cancels and replaces the first edition (ISO 18274:2004), of which it constitutes a
technical revision. It also incorporates the Technical Corrigenda ISO 18274:2004/Cor.1:2005 and
ISO 18274:2004/Cor.2:2006.
Requests for official interpretation of any aspect of this International Standard should be directed to the
Secretariat of ISO/TC 44/SC 3 via your national standards body. A complete listing of these bodies can be
found at www.iso.org.
iv © ISO 2010 – All rights reserved
ISO 18274:2010(E)
Introduction
For nickel welding consumables, there is no unique relationship between the product form (solid wire
electrode, solid strip electrode, solid wire or solid rod) and the welding process used (e.g. gas shielded metal
arc welding, gas tungsten arc welding, plasma arc welding, submerged arc welding, strip overlay welding,
laser welding or other welding processes). For this reason, the solid wire electrode, solid strip electrode, solid
wire or solid rod may be classified on the basis of any of the above product forms and can be used as
appropriate, for more than one of the above processes.
INTERNATIONAL STANDARD ISO 18274:2010(E)
Welding consumables — Solid wire electrodes, solid strip
electrodes, solid wires and solid rods for fusion welding
of nickel and nickel alloys — Classification
1 Scope
This International Standard specifies requirements for classification of solid wire electrodes, solid strip
electrodes, solid wires and solid rods for fusion welding of nickel and nickel alloys. The classification of the
solid wire electrodes, solid strip electrodes, solid wires and solid rods is based on their chemical composition.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 544, Welding consumables — Technical delivery conditions for filler materials and fluxes — Type of
product, dimensions, tolerances and markings
ISO 14344, Welding consumables — Procurement of filler materials and fluxes
ISO 80000-1:2009, Quantities and units — Part 1:General
3 Classification
The classification is divided into two parts:
a) the first part indicates the product form, being solid wire electrode, solid strip electrode, solid wire or solid
rod, see 4.1;
b) the second part gives a numerical symbol indicating the chemical composition of the solid wire electrode,
solid strip electrode, solid wire or solid rod, see Table 1.
4 Symbols and requirements
4.1 Symbols for the product form
The symbol for the solid wire electrode, solid wire or solid rod shall be “S”. The symbol for the solid strip
electrode shall be “B”.
NOTE One product form can be used for more than one weld
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.