EN 16602-60-14:2014
(Main)Space product assurance - Relifing procedure - EEE components
Space product assurance - Relifing procedure - EEE components
This standard specifies the requirements, also known as “relifing requirements”, for the planned, intentional storage, control, and removal from storage of electronic, electrical and electromechanical parts which are intended to be used for space applications.
The relifing process is a lot quality control activity. The inspections and tests defined do not constitute an up-screening or up-grading of components to a higher level of quality than procured to.
This standard is applicable to all EEE parts covered by ECSS-Q-ST-60 and used in space programmes.
This standard is not applicable to naked dice.
This standard does not cover the relifing of commercial parts.
Raumfahrtproduktsicherung - Wiederbelebungsprozeduren für EEE-Komponenten
Assurance produit des projets spatiaux - Procédure de déstockage - Composants EEE
Zagotavljanje varnih proizvodov v vesoljski tehniki - Postopek oživljanja komponent EEE
Ta standard določa zahteve, znane tudi kot »zahteve za oživljanje«, za načrtovano, namerno shranjevanje, nadzor in prekinitev shranjevanja elektronskih, električnih in elektromehanskih delov, ki so namenjeni vesoljskim uporabam. Postopek oživljanja je dejavnost nadzora kakovosti serije. Opredeljeni pregledi in preskusi ne predstavljajo presejanja ali izboljšanja komponent, da se doseže višja raven kakovosti od naročene. Ta standard velja za vse dele EEE iz standarda ECSS-Q-ST-60, ki se uporabljajo v vesoljskih programih. Ta standard se ne uporablja za elemente, ki se dobavljajo brez ovoja oziroma ohišja. Ta standard ne obravnava oživljanja komercialnih delov.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-januar-2015
Zagotavljanje varnih proizvodov v vesoljski tehniki - Postopek oživljanja
komponent EEE
Space product assurance - Relifing procedure - EEE components
Raumfahrtproduktsicherung - Wiederbelebungsprozeduren für EEE-Komponenten
Assurance produit des projets spatiaux - Procédure de déstockage - Composants EEE
Ta slovenski standard je istoveten z: EN 16602-60-14:2014
ICS:
49.140 Vesoljski sistemi in operacije Space systems and
operations
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN 16602-60-14
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2014
ICS 49.140
English version
Space product assurance - Relifing procedure - EEE
components
Assurance produit des projets spatiaux - Procédure de Raumfahrtproduktsicherung - Wiederbelebungsprozeduren
déstockage - Composants EEE für EEE-Komponenten
This European Standard was approved by CEN on 13 March 2014.
CEN and CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving
this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning
such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN and CENELEC
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN and CENELEC member into its own language and notified to the CEN-CENELEC Management Centre
has the same status as the official versions.
CEN and CENELEC members are the national standards bodies and national electrotechnical committees of Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia,
Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
CEN-CENELEC Management Centre:
Avenue Marnix 17, B-1000 Brussels
© 2014 CEN/CENELEC All rights of exploitation in any form and by any means reserved Ref. No. EN 16602-60-14:2014 E
worldwide for CEN national Members and for CENELEC
Members.
Table of contents
Foreword . 4
1 Scope . 5
2 Normative references . 6
3 Terms, definitions and abbreviated terms . 7
3.1 Terms from other standards . 7
3.2 Terms and definitions specific to the present standard . 7
3.3 Abbreviated terms. 11
3.4 Symbols . 11
4 Environmental parameters for storage . 12
4.1 General rules and requirements. 12
4.1.1 Introduction . 12
4.1.2 Procedures . 12
4.1.3 Storage area and storage zone . 12
4.1.4 Cleanliness . 12
4.1.5 ESD protection . 13
4.1.6 Packing – Packaging – Handling . 13
4.1.7 Quality assurance requirements for storage areas . 13
4.2 Storage conditions . 13
4.2.1 Air . 13
4.2.2 Temperature . 13
4.2.3 Relative humidity (RH) . 14
4.2.4 Package . 14
5 Timing parameters . 15
6 Control parameters . 16
6.1 Test requirements . 16
6.1.1 General requirements per EEE parts family: . 16
6.1.2 Specific requirements per EEE parts family:. 16
6.1.3 Electrical testing . 18
6.1.4 External visual inspection . 18
6.1.5 Seal test . 18
6.2 Nonconformance . 18
6.3 Relifing datecode . 19
6.4 Relifing report . 19
6.5 Certificate of Conformity . 19
Annex A (normative) Relifing report - DRD . 22
Annex B (informative) ESD . 25
Bibliography . 28
Figures
Figure 3-1: Timing parameters . 10
Figure A-1 : Example of a relifing traveller sheet . 24
Tables
Table 5-1: Timing parameters. 15
Table 6-1: Control parameters and detailed application of categories . 19
Table B-1 : ESD classes . 27
Foreword
This document (EN 16602-60-14:2014) has been prepared by Technical Committee
CEN/CLC/TC 5 “Space”, the secretariat of which is held by DIN.
This standard (EN 16602-60-14:2014) originates from ECSS-Q-ST-60-14C.
This European Standard shall be given the status of a national standard, either by
publication of an identical text or by endorsement, at the latest by March 2015,
and conflicting national standards shall be withdrawn at the latest by March
2015.
Attention is drawn to the possibility that some of the elements of this document
may be the subject of patent rights. CEN [and/or CENELEC] shall not be held
responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CEN by the
European Commission and the European Free Trade Association.
This document has been developed to cover specifically space systems and has
therefore precedence over any EN covering the same scope but with a wider
domain of applicability (e.g. : aerospace).
According to the CEN-CENELEC Internal Regulations, the national standards
organizations of the following countries are bound to implement this European
Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia,
Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Scope
This standard specifies the requirements, also known as “relifing requirements”,
for the planned, intentional storage, control, and removal from storage of
electronic, electrical and electromechanical parts which are intended to be used
for space applications.
The relifing process is a lot quality control activity. The inspections and tests
defined do not constitute an up-screening or up-grading of components to a
higher level of quality than procured to.
This standard is applicable to all EEE parts covered by ECSS-Q-ST-60 and used in
space programmes.
This standard is not applicable to naked dice.
This standard does not cover the relifing of commercial parts.
Normative references
The following normative documents contain provisions which, through reference
in this text, constitute provisions of this ECSS Standard. For dated references,
subsequent amendments to, or revision of any of these publications do not apply,
However, parties to agreements based on this ECSS Standard are encouraged to
investigate the possibility of applying the more recent editions of the normative
documents indicated below. For undated references, the latest edition of the
publication referred to applies.
EN reference Reference in text Title
EN 16601-00-01 ECSS-S-ST-00-01 ECSS system – Glossary of terms
EN 16602-10-09 ECSS-Q-ST-10-09 Space product assurance – Nonconformance control
system
EN 16602-60 ECSS-Q-ST-60 Space product assurance – Electrical, electronic and
electromechanical (EEE) components
EN 16602-70-01 ECSS-Q-ST-70-01 Space product assurance – Cleanliness and
contamination control
ESCC 24900 Minimum Requirements for Controlling
Environmental Contamination of Components
IPC/JEDEC J-STD-033 Standard for Handling, Packing, Shipping and Use of
Moisture/ re-flow Sensitive Surface Mount Devices
July 2002 version A
ESCC 20600 Preservation, Packaging and dispatch of SCC
Electronic Components
Terms, definitions and abbreviated terms
3.1 Terms from other standards
For the purpose of this Standard, the terms and definitions from ECSS-S-ST-00-01
and ECSS-Q-ST-60 apply.
For the purposed of this Standard the following terms from ECSS-Q-ST-70-01
apply:
clean area
cleanroom
3.2 Terms and definitions specific to the present standard
3.2.1 antistatic material
material that minimizes the generation of static charges
NOTE 1 This term refers to the reduction of triboelectric
charge generation.
NOTE 2 This property is not dependent upon material
resistivity.
3.2.2 conductive material
material with the following characteristics:
surface conductive type: materials with a surface resistivity less than
10 Ω/.
volume conductive type: materials with a volume resistivity less
than 10 Ω-cm.
3.2.3 contaminant
unwanted molecular or particulate matter (including microbiological matter) on
the surface or in the environment of interest that can affect or degrade the
relevant performance or life time
3.2.4 container
receptacle which holds, restrains or encloses an item
3.2.5 (original) date code
code used by the EEE part manufacturer at assembly step that indicates the
production date
NOTE 1 Generally four-figure codes; two for the year and
two for the week.
NOTE 2 Special lot number can also identify the date
code.
3.2.6 (relifing) date code:
code indicating the date an item is submitted to relifing
NOTE Four-figure code, two for the year and two for
the week.
3.2.7 dissipative material
material with the following characteristics:
surface conductive type: materials with a surface resistivity equal to
5 12
or greater than 10 Ω/ but less than 10 Ω/.
volume conductive type: materials with a volume resistivity equal to
4 11
or greater than 10 Ω-cm but less than 10 Ω-cm.
3.2.8 electrostatic charge
negative or positive electrical charge present on the material or item surface, at
rest
3.2.9 electrostatic discharge (ESD)
transfer of electrostatic charge between objects at different potentials caused by
direct contact or induced by an electrostatic field
3.2.10 electrostatic discharge sensitive (ESDS)
tendency of the performance of EEE parts to be affected or damaged by an ESD
event
3.2.11 ESD protected area
area which is constructed and equipped with the necessary ESD protective
materials, equipment, and procedures, to limit ESD voltages below the sensitivity
level of ESDS items handled therein
3.2.12 ESD protective material
material with one or more of the following properties: limits the generation of
electrostatic charge, dissipates electrostatic charge, and provides shielding from
electric fields
3.2.13 ESD protective packaging
packaging with ESD protective materials to prevent ESD damage to ESDS items
3.2.14 electrostatic shield
barrier or enclosure that prevents or attenuates the penetration of an electric field
E
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.