EN ISO 7823-2:2003

Plastics - Poly(methyl methacrylate) sheets - Types, dimensions and characteristics - Part 2: Extruded sheets (ISO 7823-2:2003)

ISO 7823-2:2003 specifies requirements for flat poly(methyl methacrylate) (PMMA) sheets extruded from colourless or coloured, transparent, translucent or opaque materials.
The thickness range of the sheets covered by this part of ISO 7823 is 1,5 mm to 20 mm.

Kunststoffe - Tafeln aus Polymethylmethacrylat - Typen, Maße und Eigenschaften - Teil 2: Extrudierte Tafeln (ISO 7823-2:2003)

Dieser Teil der ISO 7823 legt die Anforderungen an flache, extrudierte Polymethylmethacrylat (PMMA-)Tafeln aus farblosen und eingefärbten, durchsichtigen, durchscheinenden und undurchsichtigen Lieferformen dieses Materials, wie in 3.1 definiert, fest.
Der Dickenbereich der in diesem Teil der ISO 7823 behandelten Tafeln beträgt 1,5 mm bis 20 mm.

Plastiques - Plaques en poly(méthacrylate de méthyle) - Types, dimensions et caractéristiques - Partie 2: Plaques extrudées (ISO 7823-2:2003)

L'ISO 7823-2:2003 fixe des exigences relatives aux plaques extrudées en poly(méthacrylate de méthyle) (PMMA) planes, incolores ou colorées, transparentes, translucides ou opaques.
La plage de l'épaisseur des plaques relevant de cette partie de l'ISO 7823 est comprise entre 1,5 mm et 20 mm.

Polimerni materiali – Plošče iz polimetilmetakrilata – Vrste, mere in značilnosti – 2. del: Ekstrudirane plošče (ISO 7823-2:2003)

General Information

• Status: Published
• Publication Date: 31-May-2003
• Withdrawal Date: 30-Dec-2003
• ICS: 83.140.10 - Films and sheets
• Technical Committee: CEN/TC 249 - Plastics
• Drafting Committee: CEN/TC 249/WG 6 - Thermoplastics films, foils and sheets
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 01-Jun-2003
• Completion Date: 01-Jun-2003
• Ref Project: SIST EN ISO 7823-2:2003 - Plastics - Poly(methyl methacrylate) sheets - Types, dimensions and characteristics - Part 2: Extruded sheets (ISO 7823-2:2003)

Relations

• Replaces: EN ISO 7823-2:1996 - Plastics - Poly(methyl methacrylate) sheets - Types, dimensions and characteristics - Part 2: Melt-calendered extruded sheets (ISO 7823-2:1996)
• Effective Date: 22-Dec-2008

Standards Content (Sample)

SLOVENSKI STANDARD
01-december-2003
1DGRPHãþD
SIST EN ISO 7823-2:1999
3ROLPHUQLPDWHULDOL±3ORãþHL]SROLPHWLOPHWDNULODWD±9UVWHPHUHLQ]QDþLOQRVWL±
GHO(NVWUXGLUDQHSORãþH,62
Plastics - Poly(methyl methacrylate) sheets - Types, dimensions and characteristics -
Part 2: Extruded sheets (ISO 7823-2:2003)
Kunststoffe - Tafeln aus Polymethylmethacrylat - Typen, Maße und Eigenschaften - Teil
2: Extrudierte Tafeln (ISO 7823-2:2003)
Plastiques - Plaques en poly(méthacrylate de méthyle) - Types, dimensions et
caractéristiques - Partie 2: Plaques extrudées (ISO 7823-2:2003)
Ta slovenski standard je istoveten z: EN ISO 7823-2:2003
ICS:
83.140.10 Filmi in folije Films and sheets
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 7823-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2003
ICS 83.140.10 Supersedes EN ISO 7823-2:1996
English version
Plastics - Poly(methyl methacrylate) sheets - Types, dimensions
and characteristics - Part 2: Extruded sheets (ISO 7823-2:2003)
Plastiques - Plaques en poly(méthacrylate de méthyle) - Kunststoffe - Tafeln aus Polymethylmethacrylat - Typen,
Types, dimensions et caractéristiques - Partie 2: Plaques Maße und Eigenschaften - Teil 2: Extrudierte Tafeln (ISO
extrudées (ISO 7823-2:2003) 7823-2:2003)
This European Standard was approved by CEN on 5 May 2003.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2003 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 7823-2:2003 E
worldwide for CEN national Members.

CORRECTED  2003-09-24
Foreword
This document (EN ISO 7823-2:2003) has been prepared by Technical Committee ISO/TC 61
"Plastics" in collaboration with Technical Committee CEN/TC 249 "Plastics", the secretariat of
which is held by IBN.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by December 2003, and conflicting national
standards shall be withdrawn at the latest by December 2003.
This document supersedes EN ISO 7823-2:1996.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium, Czech
Republic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and
the United Kingdom.
Endorsement notice
The text of ISO 7823-2:2003 has been approved by CEN as EN ISO 7823-2:2003 without any
modifications.
NOTE Normative references to International Standards are listed in Annex ZA (normative).
Annex ZA
(normative)
Normative references to international publications
with their relevant European publications
This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions of
any of these publications apply to this European Standard only when incorporated in it by
amendment or revision. For undated references the latest edition of the publication referred to
applies (including amendments).
NOTE Where an International Publication has been modified by common modifications, indicated
by (mod.), the relevant EN/HD applies.
Publication Year Title EN Year
ISO 62 1999 Plastics — Determination of water absorption EN ISO 62 1999
ISO 178 2001 Plastics — Determination of flexural EN ISO 178 1996
properties
ISO 179-1 2000 Plastics — Determination of Charpy impact EN ISO 179-1 2000
properties — Part 1: Non-instrumented
impact test
ISO 291 1997 Plastics — Standard atmospheres for EN ISO 291 1997
conditioning and testing
ISO 306 1994 Plastics — Thermoplastic materials — EN ISO 306 1996
Determina-tion of Vicat softening
temperature (VST)
ISO 489 1999 Plastics — Determination of the refractive EN ISO 489 1999
index
ISO 527-1 1993 Plastics — Determination of tensile EN ISO 527-1 1996
properties — Part 1: General principles
ISO 527-2 1993 Plastics — Determination of tensile EN ISO 527-2 1996
properties — Part 2: Test conditions for
moulding and extrusion plastics
ISO 877 1994 Plastics — Methods of exposure to direct EN ISO 877 1996
weathering, to weathering using glass-filtered
daylight, and to intensified weathering by
daylight using Fresnel mirrors
ISO 1133 1997 Plastics — Determination of the melt mass- EN ISO 1133 1999
flow rate (MFR) and the melt volume-flow
rate (MVR) of thermoplastics
ISO 2039-2 1987 Plastics — Determination of hardness — EN ISO 2039-2 1999
Part 2: Rockwell hardness
ISO 2818 1994 Plastics — Preparation of test specimens by EN ISO 2818 1996
machining
ISO 4892-2 1994 Plastics — Methods of exposure to EN ISO 4892-2 1999
laboratory light sources — Part 2: Xenon-arc
sources
ISO 13468-1 1996 Plastics — Determination of the total EN ISO 13468-1 1996
luminous transmittance of transparent
materials — Part 1: Single-beam instrument
INTERNATIONAL ISO
STANDARD 7823-2
Third edition
2003-06-01
Plastics — Poly(methyl methacrylate)
sheets ― Types, dimensions and
characteristics —
Part 2:
Extruded sheets
Plastiques — Plaques en poly(méthacrylate de méthyle) ― Types,
dimensions et caractéristiques —
Partie 2: Plaques extrudées
Reference number
ISO 7823-2:2003(E)
©
ISO 2003
ISO 7823-2:2003(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

©  ISO 2003
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
ii © ISO 2003 — All rights reserved

ISO 7823-2:2003(E)
Contents Page
Foreword. iv
1 Scope.1
2 Normative references .1
3 Terms and definitions. 2
4 General requirements . 3
5 Test methods. 6
6 Retest and rejection. 8
Annex A (normative) Determination of light transmittance at 420 nm. 9
Annex B (normative) Determination of dimensional change on heating (shrinkage).10

ISO 7823-2:2003(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 7823-2 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 11, Products.
This third edition cancels and replaces the second edition (ISO 7823-2:1996), which has been technically
revised.
ISO 7823 consists of the following parts, under the general title Plastics — Poly(methyl methacrylate)
sheets ― Types, dimensions and characteristics:
 Part 1: Cast sheets
 Part 2: Extruded sheets
 Part 3: Continuous cast sheets
iv © ISO 2003 — All rights reserved

INTERNATIONAL STANDARD ISO 7823-2:2003(E)

Plastics — Poly(methyl methacrylate) sheets ― Types,
dimensions and characteristics —
Part 2:
Extruded sheets
1 Scope
This part of ISO 7823 specifies requirements for flat poly(methyl methacrylate) (PMMA) sheets extruded from
colourless or coloured, transparent, translucent or opaque materials as defined in 3.1.
The thickness range of the sheets covered by this part of ISO 7823 is 1,5 mm to 20 mm.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 62:1999, Plastics — Determination of water absorption
1)
ISO 75-1:— , Plastics — Determination of temperature of deflection under load — Part 1: General test
method
2)
ISO 75-2:— , Plastics — Determination of temperature of deflection under load — Part 2: Plastics, ebonite
and long-fibre-reinforced composites
ISO 178:2001, Plastics — Determination of flexural properties
ISO 179-1:2000, Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact
test
ISO 291:1997, Plastics — Standard atmospheres for conditioning and testing
3)
ISO 306:— , Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST)
ISO 489:1999, Plastics — Determination of refractive index
ISO 527-1:1993, Plastics — Determination of tensile properties — Part 1: General principles

1) To be published. (Revision of ISO 75-1:1993)
2) To be published. (Revision of ISO 75-2:1993)
3) To be published. (Revision of ISO 306:1994)
ISO 7823-2:2003(E)
ISO 527-2:1993, Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and
extrusion plastics
ISO 877:1994, Plastics — Methods of exposure to direct weathering, to weathering using glass-filtered
daylight, and to intensified weathering by daylight using Fresnel mirrors
4)
ISO 1133:— , Plastics — Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate
(MVR) of thermoplastics
5)
ISO 1183-1:— , Plastics — Methods for determining the density of non-cellular plastics — Part 1: Immersion
method, liquid pyknometer method and titration method
5)
ISO 1183-2:— , Plastics — Methods for determining the density of non-cellular plastics — Part 2: Density
gradient column method
ISO 1628-6:1990, Plastics — Determination of viscosity number and limiting viscosity number — Part 6:
Methyl methacrylate polymers
ISO 2039-2:1987, Plastics — Determination of hardness — Part 2: Rockwell hardness
ISO 2818:1994, Plastics — Prep
...