EN ISO 11363-1:2010

Gas cylinders - 17E and 25E taper threads for connection of valves to gas cylinders - Part 1: Specifications (ISO 11363-1:2010)

ISO 11363-1:2010 specifies dimensions and tolerances for taper screw threads of nominal diameter 17,4 mm (designated 17E) and 25,8 mm (designated 25E) used for the connection of valves to gas cylinders.
It does not cover the connection requirements for:
mechanical strength;
gas tightness;
capability of repeated assembly and dismounting operations.
Gauge inspection is covered by ISO 11363-2.

Gasflaschen - 17E und 25E kegeliges Gewinde zur Verbindung von Ventilen mit Gasflaschen - Teil 1: Spezifikationen (ISO 11363-1:2010)

Dieser Teil der ISO 11363 legt Maße und Grenzabmaße für kegelige Schraubengewinde mit einem Nenndurchmesser
von 17,4 mm (als 17E bezeichnet) und 25,8 mm (als 25E bezeichnet) für die Verbindung von
Ventilen mit Gasflaschen fest.
Er enthält keine Anforderungen an die Verbindung hinsichtlich:
⎯ der mechanischen Festigkeit;
⎯ der Gasdichtheit;
⎯ der Fähigkeit, wiederholtes Zusammenfügen und Lösen zu überstehen.
Die Lehrenprüfung ist in ISO 11363-2 beschrieben.

Bouteilles à gaz - Filetages coniques 17E et 25E pour le raccordement des robinets sur les bouteilles à gaz - Partie 1: Spécifications (ISO 11363-1:2010)

L'ISO 11363-1:2010 spécifie les dimensions et tolérances des filetages coniques à vis, de diamètre nominal 17,4 mm (désigné 17E) et 25,8 mm (désigné 25E), utilisés pour raccorder les robinets sur les bouteilles à gaz.
Elle ne comporte pas les exigences de raccordement suivantes:
résistance mécanique;
étanchéité au gaz;
capacité à répéter les opérations de montage et de démontage.
Les calibres de contrôle font l'objet de l'ISO 11363-2.

Plinske jeklenke - Konična navoja 17E in 25E za priključitev ventila na plinsko jeklenko - 1. del: Specifikacije (ISO 11363-1:2010)

Ta del ISO 11363 določa dimenzije in tolerance za konična navoja vijakov z nominalnim premerom 17,4 mm (oznaka 17E) in 25,8 mm (oznaka 25E), ki se uporabljata za priključitev ventila na plinsko jeklenko. Ne zajema zahtev za priključitev za: – mehansko trdnost; - nepropustnost za pline; - sposobnost večkratnih operacij sestavljanja in razstavljanja. Pregled merilnika je zajet v ISO 11363-2.

General Information

• Status: Withdrawn
• Publication Date: 14-May-2010
• Withdrawal Date: 20-Feb-2018
• ICS: 21.040.30 - Special screw threads
• ICS: 23.020.30 - Pressure vessels, gas cylinders
• ICS: 23.020.35 - Gas cylinders
• Technical Committee: CEN/TC 23 - Transportable gas cylinders
• Drafting Committee: CEN/TC 23 - Transportable gas cylinders
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 21-Feb-2018
• Directive: 97/23/EC - Directive 97/23/EC of the European Parliament and of the Council of 29 May 1997 on the approximation of the laws of the Member States concerning pressure equipment
• Ref Project: SIST EN ISO 11363-1:2010 - Gas cylinders - 17E and 25E taper threads for connection of valves to gas cylinders - Part 1: Specifications (ISO 11363-1:2010)

Relations

• Replaces: EN 629-1:1996 - Transportable gas cylinders - 25E taper thread for connection of valves to gas cylinders - Part 1: Specification
• Effective Date: 22-May-2010
• Replaces: EN ISO 11116-1:1999 - Gas cylinders - 17E taper thread for connection of valves to gas cylinders - Part 1: Specifications (ISO 11116-1:1999)
• Effective Date: 22-Dec-2008
• Replaced By: EN ISO 11363-1:2018 - Gas cylinders - 17E and 25E taper threads for connection of valves to gas cylinders - Part 1: Specifications (ISO 11363-1:2018)
• Effective Date: 28-Feb-2018
• Corrected By: EN ISO 11363-1:2010/AC:2011 - Gas cylinders - 17E and 25E taper threads for connection of valves to gas cylinders - Part 1: Specifications - Technical Corrigendum 1 (ISO 11363-1:2010/Cor 1:2011)
• Effective Date: 08-Jun-2022
• Corrected By: EN ISO 11363-1:2010/AC:2012 - Gas cylinders - 17E and 25E taper threads for connection of valves to gas cylinders - Part 1: Specifications - Technical Corrigendum 2 (ISO 11363-1:2010/Cor 2:2012)
• Effective Date: 08-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
01-november-2010
1DGRPHãþD
SIST EN 629-1:1999
SIST EN ISO 11116-1:1999
3OLQVNHMHNOHQNH.RQLþQDQDYRMD(LQ(]DSULNOMXþLWHYYHQWLODQDSOLQVNR
MHNOHQNRGHO6SHFLILNDFLMH,62
Gas cylinders - 17E and 25E taper threads for connection of valves to gas cylinders -
Part 1: Specifications (ISO 11363-1:2010)
Gasflaschen - 17E und 25E kegeliges Gewinde zur Verbindung von Ventilen mit
Gasflaschen - Teil 1: Anforderungen (ISO 11363-1:2010)
Bouteilles à gaz - Filetages coniques 17E et 25E pour le raccordement des robinets sur
les bouteilles à gaz - Partie 1: Spécifications (ISO 11363-1:2010)
Ta slovenski standard je istoveten z: EN ISO 11363-1:2010
ICS:
21.040.30 Posebni navoji Special screw threads
23.020.30 7ODþQHSRVRGHSOLQVNH Pressure vessels, gas
MHNOHQNH cylinders
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 11363-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2010
ICS 23.020.30 Supersedes EN 629-1:1996, EN ISO 11116-1:1999
English Version
Gas cylinders - 17E and 25E taper threads for connection of
valves to gas cylinders - Part 1: Specifications (ISO 11363-
1:2010)
Bouteilles à gaz - Filetages coniques 17E et 25E pour le Gasflaschen - 17E und 25E kegeliges Gewinde zur
raccordement des robinets sur les bouteilles à gaz - Partie Verbindung von Ventilen mit Gasflaschen - Teil 1:
1: Spécifications (ISO 11363-1:2010) Spezifikationen (ISO 11363-1:2010)
This European Standard was approved by CEN on 23 January 2010.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11363-1:2010: E
worldwide for CEN national Members.

Contents Page
Foreword .3

Foreword
This document (EN ISO 11363-1:2010) has been prepared by Technical Committee ISO/TC 58 "Gas
cylinders" in collaboration with Technical Committee CEN/TC 23 “Transportable gas cylinders” the secretariat
of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by November 2010, and conflicting national standards shall be withdrawn
at the latest by November 2010.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 629-1:1996, EN ISO 11116-1:1999.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 11363-1:2010 has been approved by CEN as a EN ISO 11363-1:2010 without any
modification.
INTERNATIONAL ISO
STANDARD 11363-1
First edition
2010-05-15
Gas cylinders — 17E and 25E taper
threads for connection of valves to gas
cylinders —
Part 1:
Specifications
Bouteilles à gaz — Filetages coniques 17E et 25E pour le raccordement
des robinets sur les bouteilles à gaz —
Partie 1: Spécifications
Reference number
ISO 11363-1:2010(E)
©
ISO 2010
ISO 11363-1:2010(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

©  ISO 2010
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
ii © ISO 2010 – All rights reserved

ISO 11363-1:2010(E)
Contents Page
Foreword .iv
Introduction.v
1 Scope.1
2 Terms and definitions .1
2.1 General .1
2.2 Terms relating to cones.2
2.3 Terms relating to diameter .2
2.4 Terms relating to reference .3
3 Requirements.4
3.1 Thread handedness.4
3.2 Taper.4
3.3 Thread profile.4
3.4 Pitch, P.4
3.5 Dimensions .4
4 Thread end finish.7
5 Marking.8
Bibliography.9

ISO 11363-1:2010(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to
...