EN ISO 8130-6:2010

Coating Powders - Part 6: Determination of gel time of thermosetting coating powders at a given temperature (ISO 8130-6:1992, including Amd 1:1998)

The method is based on heating a test portion of a specified volume to a specified temperature, normally 180 °C, in a depression in an electrically heated steel block and determination of the time at which threads can no longer be pulled from the molten product.

Pulverlacke - Teil 6: Bestimmung der Gelzeit von wärmehärtenden Pulverlacken bei einer gegebenen Temperatur (ISO 8130-6:1992, einschließlich Amd 1:1998)

Dieser Teil von ISO 8130 legt ein Verfahren zum Bestimmen der Zeitdauer fest, die notwendig ist, damit ein
wärmehärtbarer Pulverlack bei einer festgelegten Temperatur, im Allgemeinen 180 °C, geliert.
ANMERKUNG 1 Die Bestimmung der Gelzeit ist ein sehr einfaches Verfahren zur Charakterisierung und Qualitätskontrolle
von Pulverlacken. Die nach diesem Verfahren bestimmte Gelzeit steht jedoch nicht in direktem Bezug zu der
Zeitspanne, die ein Pulverlack bei praktischen Anwendungen zum Härten benötigt.
Das Verfahren ist nicht anwendbar auf Pulverlacke mit Gelzeiten unter 15 s.

Poudres pour revêtement - Partie 6: Détermination du temps de gélification à une température donnée de poudres thermodurcissables (ISO 8130-6:1992, Amd 1:1998 inclus)

Cette partie de la CEI 60641 contient des définitions relatives à une classification des cartons comprimés et des papiers comprimés à usages électriques, ainsi que les exigences générales. Les principales modifications par rapport à l'édition précédente sont: le type de finition de surface ne doit plus être spécifié dans la norme, les épaisseurs nominales fixes ont été remplacées par des épaisseurs préférentielles, les types B.6 et P.6 ont été remplacés mais les désignations ont été conservées et les types B.7 et P.7 ont été supprimés.

Praškasti premazi - 6. del: Določanje časa želiranja termoreaktivnih praškastih premazov pri dani temperaturi (ISO 8130-6:1992, vključno z dopolnilom 1:1998)

Ta del standarda ISO 8130 določa metodo za določanje časa, ki je potreben, da se termoreaktivni praškasti premaz pri določeni temperaturi, običajno pri 180 °C, želira. OPOMBA 1 Določanja časa želiranja je zelo preprosta metoda za določanje značilnosti in nadzor kakovosti praškastih premazov. Vendar pa čas želiranja po tej metodi ni neposredno povezan s časom za sušenje praška pri praktičnih aplikacijah. Ta metoda se ne uporablja za praškaste premaze z zelo kratkim časom želiranja (krajšim od 15 s).

General Information

• Status: Withdrawn
• Publication Date: 09-Nov-2010
• Withdrawal Date: 13-Jul-2021
• ICS: 87.040 - Paints and varnishes
• Technical Committee: CEN/TC 139 - Paints and varnishes
• Drafting Committee: CEN/TC 139 - Paints and varnishes
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Due Date: 14-Jul-2021
• Completion Date: 14-Jul-2021
• Ref Project: SIST EN ISO 8130-6:2012 - Coating Powders - Part 6: Determination of gel time of thermosetting coating powders at a given temperature (ISO 8130-6:1992, including Amd 1:1998)

Relations

• Replaced By: EN ISO 8130-6:2021 - Coating powders - Part 6: Determination of gel time of thermosetting coating powders at a given temperature (ISO 8130-6:2021)
• Effective Date: 21-Jul-2021

Standards Content (Sample)

SLOVENSKI STANDARD
01-november-2012
3UDãNDVWLSUHPD]LGHO'RORþDQMHþDVDåHOLUDQMDWHUPRUHDNWLYQLKSUDãNDVWLK
SUHPD]RYSULGDQLWHPSHUDWXUL,62YNOMXþQR]GRSROQLORP
Coating Powders - Part 6: Determination of gel time of thermosetting coating powders at
a given temperature (ISO 8130-6:1992, including Amd 1:1998)
Pulverlacke - Teil 6: Bestimmung der Gelzeit von wärmehärtenden Pulverlacken bei
einer gegebenen Temperatur (ISO 8130-6:1992, einschließlich Amd 1:1998)
Poudres pour revêtement - Partie 6: Détermination du temps de gélification à une
température donnée de poudres thermodurcissables (ISO 8130-6:1992, Amd 1:1998
inclus)
Ta slovenski standard je istoveten z: EN ISO 8130-6:2010
ICS:
87.040 Barve in laki Paints and varnishes
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 8130-6
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2010
ICS 87.040
English Version
Coating Powders - Part 6: Determination of gel time of
thermosetting coating powders at a given temperature (ISO
8130-6:1992, including Amd 1:1998)
Poudres pour revêtement - Partie 6: Détermination du Pulverlacke - Teil 6: Bestimmung der Gelzeit von
temps de gélification à une température donnée de wärmehärtenden Pulverlacken bei einer gegebenen
poudres thermodurcissables (ISO 8130-6:1992, Amd Temperatur (ISO 8130-6:1992, einschließlich Amd 1:1998)
1:1998 inclus)
This European Standard was approved by CEN on 16 October 2010.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 8130-6:2010: E
worldwide for CEN national Members.

Contents Page
Foreword .3

Foreword
The text of ISO 8130-6:1992, including Amd 1:1998 has been prepared by Technical Committee ISO/TC 35
“Paints and varnishes” of the International Organization for Standardization (ISO) and has been taken over as
held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by May 2011, and conflicting national standards shall be withdrawn at the
latest by May 2011.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 8130-6:1992, including Amd 1:1998 has been approved by CEN as a EN ISO 8130-6:2010
without any modification.
INTERNATIONAL
STANDARD 8130-6
First edition
1992-l 2-15
Coating powders -
Part 6:
Determination of gel time of thermosetting
coating powders at a given temperature
Poudres pour revetement -
Partie 6: Dktermination du temps de gMkation A une tern@ature
don&e de poudres thermodurcissables
~--
____________
___- --
Reference number
--
_--~
IS0 8130-6:1992(E)
________ -__----.
IS0 8130-6:1992(E)
Foreword
IS0 (the International Organization for Standardization) is a worldwide
federation of national standards bodies (IS0 member bodies). The work
of preparing International Standards is normally carried out through IS0
technical committees. Each member body interested in a subject for
which a technical committee has been established has the right to be
represented on that committee. International organizations, govern-
mental and non-governmental, in liaison with ISO, also take part in the
work. IS0 collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnicai standardization.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an Inter-
national Standard requires approval by at least 75 % of the member
bodies casting a vote.
International Standard IS0 8130-6 was prepared by Technical Committee
ISO/TC 35, Paints and varnishes, Sub-Committee SC 9, General test
methods for paints and varnishes.
IS0 8130 consists of the following parts, under the general title Coating
powders:
- Part 1: Determination of particle size distribution by sieving
- Part 2: Determination of density by gas comparison pyknometer
(referee method)
- Part 3: Determination of density by liquid displacement
pyknometer
- Part 4: Calculation of lower explosion limit
- Part 5: Determination of flow properties of a powder/air mixture
- Part 6: Determination of gel time of thermosetting coating po wders
at a given temperature
- Part 7: Determination of loss of mass on stoving
- Part 8: Assessment of the storage stability of thermosetting pow-
ders
0 IS0 1992
All rights reserved. No part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without
permission in writing from the publisher.
International Organization for Standardization
Case Postale 56 l CH-1211 GetWe 20 l Switzerland
Printed in Switzerland
ii
IS0 8130=6:1992(E)
-
Part 9: Sampling
This page intentionally left blank

INTERNATIONAL STANDARD IS0 8130-6:1992(E)
Coating powders -
Part 6:
Determination of ael time of thermosetting coating powders at
a given tempera&e
3.1 gel time: The time taken for a specified volume
1 Scope
of coating powder to become non-deformable, under
specified conditions, after melting.
This part of IS0 8130 specifies a method for the de-
termination of the time for a thermosetting coating
powder to gel at a specified temperature, normally
4 Principle
180 “C.
A test portion of a specified volume of coating pow-
The determination of the gel time is a very
NOTE 1
der is heated to a specified temperature in a de-
simple method for the characterization and quality control
pression in a heating block. The time at which
of coating powders. However, the gel time determined by
threads can no longer be pulled from the molten
this method is not directly related to the time for a
...