iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN ISO 6149-1:2007

(Main)

Connections for hydraulic fluid power and general use - Ports and stud ends with ISO 261 metric threads and O-ring sealing - Part 1: Ports with truncated housing for O-ring seal (ISO 6149-1:2007)

Connections for hydraulic fluid power and general use - Ports and stud ends with ISO 261 metric threads and O-ring sealing - Part 1: Ports with truncated housing for O-ring seal (ISO 6149-1:2007)

ISO 6149-1:2006 specifies dimensions for metric ports for use with the adjustable and non-adjustable stud ends detailed in ISO 6149-2:2006 and ISO 6149-3:2006.
Ports in accordance with ISO 6149-1:2006 may be used at working pressures up to 63 MPa (630 bar) for non-adjustable stud ends and 40 MPa (400 bar) for adjustable stud ends. The permissible working pressure depends upon port size, materials, design, working conditions, application, etc. See ISO 6149-2:2006 and ISO 6149-3:2006 for pressure ratings.

Leitungsanschlüsse für Fluidtechnik und allgemeine Anwendung - Einschraublöcher und Einschraubzapfen mit metrischem Gewinde nach ISO 261 und O-Ring-Abdichtung - Teil 1: Einschraublöcher mit Ansenkung für O-Ring-Abdichtung (ISO 6149-1:2007)

Dieser Teil der ISO 6149 legt Maße für Einschraublöcher mit metrischem Gewinde für Einschraubzapfen und richtungseinstellbare Einschraubzapfen nach ISO 6149-2 und ISO 6149-3 fest.
Einschraublöcher nach diesem Teil der ISO 6149 dürfen bei Arbeitsdrücken bis 63 MPa (630 bar )) mit Einschraubzapfen und bis 40 MPa (400 bar) mit richtungseinstellbaren Einschraubzapfen verwendet werden. Der zulässige Arbeitsdruck ist abhängig von der Größe des Einschraubloches, den Werkstoffen, Konstruktion, Betriebsbedingungen, Anwendungsfall usw. Druckstufen siehe ISO 6149-2 und ISO 6149-3.
Die Anwender dieses Teils der ISO 6149 sollten sicherstellen, dass eine ausreichende Wandstärke am Einschraubloch vorhanden ist, um dem Druck standzuhalten.
ANMERKUNG   Die Einleitung zu diesem Teil der ISO 6149 enthält Empfehlungen für die bei Neukonstruktionen in
hydraulischen Anlagen der Fluidtechnik zu verwendenden Einschraublöcher und Einschraubzapfen.

Raccordements pour transmissions hydrauliques et applications générales - Orifices et éléments mâles à filetage métrique ISO 261 et joint torique - Partie 1: Orifices à joint torique dans un logement tronconique (ISO 6149-1:2007)

L'ISO 6149:2006 spécifie les dimensions des orifices métriques utilisables avec les éléments mâles orientables et non orientables faisant l'objet de l'ISO 6149-2:2006 et de l'ISO 6149-3:2006.
Les orifices conformes à l'ISO 6149:2006 peuvent être utilisés jusqu'à des pressions de travail de 63 MPa (630 bar) pour les éléments mâles non orientables et de 40 MPa (400 bar) pour les éléments mâles orientables. La pression de travail admissible dépend de la dimension de l'orifice, des matériaux, de la conception, des conditions de travail, de l'utilisation, etc. Voir l'ISO 6149-2:2006 et l'ISO 6149-3:2006 pour les pressions de travail.

Priključevanja v fluidni tehniki in splošna uporaba - Odprtine in priključki z navoji po ISO 261 in tesnilkami O - 1. del: Odprtine s tesnilko O v koničnem ohišju (ISO 6149-1:2006)

General Information

Status
Withdrawn
Publication Date
20-Feb-2007
Withdrawal Date
14-May-2019
ICS
23.100.40 - Piping and couplings
Technical Committee
ECISS/TC 110 - Steel tubes, and iron and steel fittings
Drafting Committee
ECISS/TC 29/SC 3 - Fittings
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
15-May-2019
Ref Project
SIST EN ISO 6149-1:2007 - Connections for hydraulic fluid power and general use - Ports and stud ends with ISO 261 metric threads and O-ring sealing - Part 1: Ports with truncated housing for O-ring seal (ISO 6149-1:2006)

Relations

Replaced By
EN ISO 6149-1:2019 - Connections for hydraulic fluid power and general use - Ports and stud ends with ISO 261 metric threads and O-ring sealing - Part 1: Ports with truncated housing for O-ring seal (ISO 6149-1:2019)
Effective Date
09-Dec-2015

Buy Standard

EN ISO 6149-1:2007EN ISO 6149-1:2007
PreviousNext
Standard
EN ISO 6149-1:2007
English language
12 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 6149-1:2007
01-maj-2007
3ULNOMXþHYDQMDYIOXLGQLWHKQLNLLQVSORãQDXSRUDED2GSUWLQHLQSULNOMXþNL]QDYRML
SR,62LQWHVQLONDPL2GHO2GSUWLQHVWHVQLONR2YNRQLþQHPRKLãMX ,62

Connections for hydraulic fluid power and general use - Ports and stud ends with ISO
261 metric threads and O-ring sealing - Part 1: Ports with truncated housing for O-ring
seal (ISO 6149-1:2006)
Leitungsanschlüsse für Fluidtechnik und allgemeine Anwendung - Einschraublöcher und
Einschraubzapfen mit metrischem Gewinde nach ISO 261 und O-Ring-Abdichtung - Teil
1: Einschraublöcher mit Ansenkung für O-Ring-Abdichtung (ISO 6149-1:2006)
Raccordements pour transmissions hydrauliques et applications générales - Orifices et
éléments mâles a filetage métrique ISO 261 et joint torique - Partie 1: Orifices a joint
torique dans un logement tronconique (ISO 6149-1:2006)
Ta slovenski standard je istoveten z: EN ISO 6149-1:2007
ICS:
23.100.40 Cevna napeljava in sklopke Piping and couplings
SIST EN ISO 6149-1:2007 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

EUROPEAN STANDARD
EN ISO 6149-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2007
ICS 23.100.40

English Version
Connections for hydraulic fluid power and general use - Ports
and stud ends with ISO 261 metric threads and O-ring sealing -
Part 1: Ports with truncated housing for O-ring seal (ISO 6149-
1:2006)
Raccordements pour transmissions hydrauliques et Leitungsanschlüsse für Fluidtechnik und allgemeine
applications générales - Orifices et éléments mâles à Anwendung - Einschraublöcher und Einschraubzapfen mit
filetage métrique ISO 261 et joint torique - Partie 1: Orifices metrischem Gewinde nach ISO 261 und O-Ring-
à joint torique dans un logement tronconique (ISO 6149- Abdichtung - Teil 1: Einschraublöcher mit Ansenkung für O-
1:2006) Ring-Abdichtung (ISO 6149-1:2006)
This European Standard was approved by CEN on 4 February 2007.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2007 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 6149-1:2007: E
worldwide for CEN national Members.

---------------------- Page: 2 ----------------------

EN ISO 6149-1:2007 (E)






Foreword



The text of ISO 6149-1:2006 has been prepared by Technical Committee ISO/TC 131 "Fluid
power systems” of the International Organization for Standardization (ISO) and has been taken
over as EN ISO 6149-1:2007 by Technical Committee ECISS/TC 29 "Steel tubes and fittings for
steel tubes", the secretariat of which is held by UNI.

This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by August 2007, and conflicting national
standards shall be withdrawn at the latest by August 2007.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United
Kingdom.


Endorsement notice

The text of ISO 6149-1:2006 has been approved by CEN as EN ISO 6149-1:2007 without any
modifications.

2

---------------------- Page: 3 ----------------------

INTERNATIONAL ISO
STANDARD 6149-1
Second edition
2006-02-15

Connections for hydraulic fluid power
and general use — Ports and stud ends
with ISO 261 metric threads and O-ring
sealing —
Part 1:
Ports with truncated housing for O-ring
seal
Raccordements pour transmissions hyd
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 1179-2:2022(Main)
Connections for general use and fluid power - Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing - Part 2: Heavy-duty (S series) and light-duty (L series) stud ends with elastomeric sealing (type E) (ISO 1179-2:2022)
SIST EN ISO 1179-2:2023

This document specifies the dimensions, performance requirements and test procedures for heavy-duty (S series) and light-duty (L series) stud ends with threads, and the elastomeric sealing (type E) that is used with them as defined in ISO 228-1.
Heavy-duty (S series) stud ends with type E sealing in accordance with this document can be used at working pressures up to 63 MPa (630 bar). Light-duty (L series) stud ends with type E sealing in accordance with this document can be used at working pressures up to 25 MPa (250 bar). The permissible working pressure depends upon size, materials, design, working conditions, application, etc.
This document is applicable to connectors detailed in ISO 8434-1, ISO 8434-2 and ISO 8434-6.
NOTE      The Introduction gives recommendations for ports and stud ends to be used for new designs in hydraulic and pneumatic fluid power applications.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 6149-1:2022(Main)
Connections for hydraulic fluid power and general use - Ports and stud ends with ISO 261 metric threads and O-ring sealing - Part 1: Ports with truncated housing for O-ring seal (ISO 6149-1:2022)
SIST EN ISO 6149-1:2022

This document specifies dimensions for metric ports for use with the adjustable and non-adjustable stud ends as described in ISO 6149‑2 and ISO 6149‑3.
Ports in accordance with this document can be used at working pressures up to 63 MPa (630 bar[1]) for non-adjustable stud ends and 40 MPa (400 bar) for adjustable stud ends. The permissible working pressure depends upon port size, materials, design, working conditions, application, etc. See ISO 6149‑2 and ISO 6149‑3 for pressure ratings.
NOTE      The Introduction of this document gives recommendations for ports and stud ends to be used for new designs in hydraulic fluid power applications.
[1] 1 bar = 0,1 MPa = 105 Pa; 1 MPa = 1 N/mm2.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 19879:2021(Main)
Metallic tube connections for fluid power and general use - Test methods for hydraulic fluid power connections (ISO 19879:2021)
SIST EN ISO 19879:2021

This document specifies uniform methods for the testing and performance evaluation of metallic tube connections, stud ends for ports and flange connections for use in hydraulic fluid power applications. This document does not apply to the testing of hydraulic quick-action couplings, which is covered by ISO 18869.
Tests outlined in this document are independent of each other and document the method to follow for each test. See the appropriate component International Standard for indications of which tests to conduct and for performance criteria.
For qualification of the connector, the minimum number of samples specified in this document is tested, unless otherwise specified in the relevant connector standard or as agreed upon by the manufacturer and the user.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 8434-1:2018(Main)
Metallic tube connections for fluid power and general use - Part 1: 24° cone connectors (ISO 8434-1:2018, Corrected version 2018-10)
SIST EN ISO 8434-1:2018

This document specifies the general and dimensional requirements for 24° cone connectors using cutting ring and O‑ring seal cone (referred to as DKO) suitable for use with ferrous and non‑ferrous tubes with outside diameters from 4 mm to 42 mm inclusive. These connectors are for use in fluid power and general applications within the limits of pressure and temperature specified in this document.
They are intended for the connection of plain end tubes and hose fittings to ports in accordance with ISO 6149‑1, ISO 1179‑1 and ISO 9974‑1. (See ISO 12151‑2 for a related hose fitting specification.)
These connectors provide full-flow connections in hydraulic systems operating to the working pressures shown in Table 1. Because many factors influence the pressure at which a system performs satisfactorily, these values are not intended to be understood as guaranteed minimums. For every application, sufficient testing is meant to be conducted and reviewed by both the user and manufacturer to ensure that required performance levels are met.
NOTE 1    For new designs in hydraulic fluid power applications, see the requirements given in 9.6. Where the requirements of the application allow for the use of elastomeric seals, connector designs that conform to International Standards and incorporate elastomeric sealing are preferred.
NOTE 2    For use under conditions outside the pressure and/or temperature limits specified, see 5.4.
This document also specifies a performance and qualification test for these connectors.

  • Standard
    60 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    60 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 6149-4:2017(Main)
Connections for fluid power and general use - Ports and stud ends with ISO 261 metric threads and O-ring sealing - Part 4: Dimensions, design, test methods and requirements for external hex and internal hex port plugs (ISO 6149-4:2017)
SIST EN ISO 6149-4:2017

ISO 6149-4:2017 specifies dimensions and performance requirements for external hex and internal hex port plugs for use with ISO 6149‑1 ports.
Port plugs in accordance with this document can be used at working pressures up to 63 MPa (630 bar[1]). The permissible working pressure depends upon the plug end size, materials, design, working conditions, application, etc.
Conformance to the dimensional information in this document does not guarantee rated performance. Each manufacturer is expected to perform testing according to the specification contained in this document to assure that components comply with the performance ratings.
WARNING: The use of stud ends conforming to this document with ports conforming to the relevant parts of ISO 1179, ISO 9974 and ISO 11926 could lead to a hazardous situation.
[1] 1 bar = 0,1 MPa = 105 Pa; 1 MPa = 1 N/mm2.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 1179-1:2013(Main)
Connections for general use and fluid power - Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing - Part 1: Threaded ports (ISO 1179-1:2013)
SIST EN ISO 1179-1:2014

ISO 1179-1:2013 specifies dimensions for ports with ISO 228‑1 threads for use with non-adjustable stud ends described in ISO 1179‑2, ISO 1179‑3 and ISO 1179‑4 and with adjustable stud ends described in ISO 1179‑3.
Ports in accordance with ISO 1179-1:2013 are applicable for use with ISO 1179‑2 heavy-duty (S series) stud ends with type E sealing at working pressures up to 63 MPa (630 bar) and light-duty (L series) stud ends at working pressures up to 25 MPa (250 bar), ISO 1179‑3 light-duty (L series) stud ends with type G sealing at working pressures up to 31,5 MPa (315 bar), and with ISO 1179‑3 light-duty (L series) adjustable stud ends with type H sealing at working pressures up to 20 MPa (200 bar), and ISO 1179‑4 stud ends with type B sealing at working pressures up to 40 MPa (400 bar) for the S series, up to 25 MPa (250 bar) for the L series, and up to 10 MPa (100 bar) for the LL series, except for the G2 size port, which in hydraulic fluid power systems is used mainly with accumulators and for which ISO 1179‑3 and ISO 1179‑4 do not specify stud ends. The permissible working pressure depends upon size, materials, design, working conditions, application, etc.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 1179-3:2008(Main)
Connections for general use and fluid power - Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing - Part 3: Light-duty (L series) stud ends with sealing by O-ring with retaining ring (types G and H) (ISO 1179-3:2007)
SIST EN ISO 1179-3:2008

ISO 1179-3:2007 specifies dimensions, performance requirements and test procedures for non-adjustable and adjustable light-duty (L series) stud ends with ISO 228-1 threads with sealing by O-ring with retaining ring (types G and H, respectively).

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 1179-4:2008(Main)
Connections for general use and fluid power - Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing - Part 4: Stud ends for general use only with metal-to-metal sealing (type B) (ISO 1179-4:2007)
SIST EN ISO 1179-4:2008

ISO 1179-4:2007 specifies dimensions, performance requirements and test procedures for stud ends with ISO 228-1 threads and metal-to-metal sealing for general use only. These stud ends should not be used for leak-free hydraulic fluid power applications.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 6149-3:2007(Main)
Connections for hydraulic fluid power and general use - Ports and stud ends with ISO 261 metric threads and O-ring sealing - Part 3: Dimensions, design, test methods and requirements for light-duty (L series) stud ends (ISO 6149-3:2006)
SIST EN ISO 6149-3:2007

ISO 6149-3:2006 specifies dimensions, performance requirements and test procedures for metric adjustable and non-adjustable light-duty (L series) stud ends and O-rings.
Stud ends in accordance with ISO 6149-3:2006 may be used at working pressures up to 40 MPa (400 bar) for non-adjustable stud ends and 31,5 MPa (315 bar) for adjustable stud ends. The permissible working pressure depends upon the stud end size, materials, design, working conditions, application, etc.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 6149-2:2007(Main)
Connections for hydraulic fluid power and general use - Ports and stud ends with ISO 261 metric threads and O-ring sealing - Part 2: Dimensions, design, test methods and requirements for heavy-duty (S series) stud ends (ISO 6149-2:2007)
SIST EN ISO 6149-2:2007

ISO 6149-2:2006 specifies dimensions, performance requirements and test procedures for metric adjustable and non-adjustable heavy-duty (S series) stud ends and O-rings.
Stud ends in accordance with ISO 6149-2:2006 may be used at working pressures up to 63 MPa (630 bar) for non-adjustable stud ends and 40 MPa (400 bar) for adjustable stud ends. The permissible working pressure depends upon the stud end size, materials, design, working conditions, application, etc.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day