EN ISO 23277:2009
(Main)Non-destructive testing of welds - Penetrant testing of welds - Acceptance levels (ISO 23277:2006)
Non-destructive testing of welds - Penetrant testing of welds - Acceptance levels (ISO 23277:2006)
ISO 23277:2006 specifies acceptance levels for indications from surface breaking imperfections in metallic welds detected by penetrant testing.
The acceptance levels in ISO 23277:2006 are primarily intended for use during manufacture examination, but where appropriate they can be used for in-service inspection.
These acceptance levels can be related to welding standards, application standards, specifications or codes.
Zerstörungsfreie Prüfung von Schweißverbindungen - Eindringprüfung von Schweißverbindungen - Zulässigkeitsgrenzen (ISO 23277:2006)
Dieses Dokument legt Zulässigkeitsgrenzen für Anzeigen von Oberflächenunregelmäßigkeiten in metallischen Schweißverbindungen fest, die mit der Eindringprüfung nachgewiesen werden.
Die Zulässigkeitsgrenzen sind hauptsächlich für die Anwendung während der Herstellung vorgesehen, können aber auch bei der Betriebsprüfung angewendet werden, wenn es angemessen ist.
Die Zulässigkeitsgrenzen in diesem Dokument beruhen auf der Auffindbarkeit, die erwartet werden kann, wenn die Techniken nach ISO 3452 und die im Anhang A empfohlenen Prüfparameter verwendet werden. Die Zulässigkeitsgrenzen können sich auf Schweißnormen, Anwendungsnormen, Spezifikationen oder Codes beziehen. Eine solche Beziehung ist für ISO 5817 und ISO 10042 in ISO 17635 aufgezeigt.
Contrôle non destructif des assemblages soudés - Contrôle par ressuage des soudures - Niveaux d'acceptation (ISO 23277:2006)
L'ISO 23277:2006 spécifie les niveaux d'acceptation pour les indications des défauts débouchants observés sur des soudures sur matériaux métalliques lors du contrôle par ressuage.
Les niveaux d'acceptation de l'ISO 23277:2006 sont essentiellement destinés à être utilisés pour le contrôle de fabrication, mais ils peuvent également, le cas échéant, servir pour le contrôle en service.
Ces niveaux d'acceptation peuvent être reliés à des normes de soudage, des normes d'application, des spécifications ou des codes.
Neporušitveno preskušanje zvarnih spojev - Preskušanje zvarnih spojev s penetranti - Stopnje sprejemljivosti (ISO 23277:2006)
Ta mednarodni standard določa stopnje sprejemljivosti za indikacije nepravilnosti z razpokami na površini v kovinskih zvarih, ki se detektirajo s preskušanjem s penetranti. Stopnje sprejemljivosti so namenjene predvsem uporabi pri proizvodnih pregledih, po potrebi pa se lahko uporabijo tudi za nadzor med obratovanjem. Stopnje sprejemljivosti v tem mednarodnem standardu temeljijo na detekcijskih zmogljivostih, ki jih lahko pričakujemo pri uporabi tehnik, navedenih v ISO 3452, in parametrov, ki jih priporoča Dodatek A. Stopnje sprejemljivosti se lahko nanašajo na standarde varjenja, standarde uporabe, specifikacije ali šifre. Takšen odnos je prikazan v ISO 17635 za ISO 5817 in ISO 10042.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-april-2010
1DGRPHãþD
SIST EN 1289:1999
SIST EN 1289:1999/A1:2003
SIST EN 1289:1999/A2:2004
Neporušitveno preskušanje zvarnih spojev - Preskušanje zvarnih spojev s
penetranti - Stopnje sprejemljivosti (ISO 23277:2006)
Non-destructive testing of welds - Penetrant testing of welds - Acceptance levels (ISO
23277:2006)
Zerstörungsfreie Prüfung von Schweißverbindungen - Eindringprüfung von
Schweißverbindungen - Zulässigkeitsgrenzen (ISO 23277:2006)
Contrôle non destructif des assemblages soudés - Contrôle par ressuage des soudures -
Niveaux d'acceptation (ISO 23277:2006)
Ta slovenski standard je istoveten z: EN ISO 23277:2009
ICS:
25.160.40 Varjeni spoji in vari Welded joints
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 23277
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2009
ICS 25.160.40 Supersedes EN 1289:1998
English Version
Non-destructive testing of welds - Penetrant testing of welds -
Acceptance levels (ISO 23277:2006)
Contrôle non destructif des assemblages soudés - Contrôle Zerstörungsfreie Prüfung von Schweißverbindungen -
par ressuage des soudures - Niveaux d'acceptation (ISO Eindringprüfung von Schweißverbindungen -
23277:2006) Zulässigkeitsgrenzen (ISO 23277:2006)
This European Standard was approved by CEN on 24 October 2009.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 23277:2009: E
worldwide for CEN national Members.
Contents Page
Foreword .3
Foreword
The text of ISO 23277:2006 has been prepared by Technical Committee ISO/TC 44 “Welding and allied
processes” of the International Organization for Standardization (ISO) and has been taken over as EN ISO
23277:2009 by Technical Committee CEN/TC 121 “Welding” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by May 2010, and conflicting national standards shall be withdrawn at the
latest by May 2010.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 1289:1998.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 23277:2006 has been approved by CEN as a EN ISO 23277:2009 without any modification.
INTERNATIONAL ISO
STANDARD 23277
First edition
2006-10-01
Non-destructive testing of welds —
Penetrant testing of welds — Acceptance
levels
Contrôle non destructif des assemblages soudés — Contrôle par
ressuage des soudures — Niveaux d'acceptation
Reference number
ISO 23277:2006(E)
©
ISO 2006
ISO 23277:2006(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2006
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2006 – All rights reserved
ISO 23277:2006(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 23277 was prepared by the European Committee for Standardization (CEN) Technical Committee
CEN/TC 121, Welding (as EN 1289:1998 and its Amd.1:2002 and Amd.2:2003), and was adopted,
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.