EN 18007-2:2024
(Main)Electromagnetic pulse welding - Part 2: Design of welded joints
Electromagnetic pulse welding - Part 2: Design of welded joints
This document specifies design requirements for electromagnetic pulse welds and provides design guidelines for electromagnetic pulse welding.
Elektromagnetisches Pulsschweißen - Teil 2: Ausführung der Schweißverbindungen
Dieses Dokument legt die Anforderungen an die Ausführung von elektromagnetischen Pulsschweißungen fest und enthält Leitlinien für die Ausführung von elektromagnetischen Pulsschweißungen.
Soudage par impulsion électromagnétique - Partie 2 : Conception des assemblages soudés
Le présent document spécifie les exigences de conception pour les soudures par impulsion électromagnétique et fournit des lignes directrices de conception pour le soudage par impulsion électromagnétique.
Elektromagnetno utripno varjenje - 2. del: Načrtovanje zvarnih spojev
Ta dokument določa zahteve za popis in kvalifikacijo varilnih postopkov za elektromagnetno utripno varjenje.
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2024
Elektromagnetno utripno varjenje - 2. del: Načrtovanje zvarnih spojev
Electromagnetic pulse welding - Part 2: Design of welded joints
Schweißen und verwandte Verfahren - Elektromagnetisches Pulsschweißen - Teil 2:
Ausführung der Schweißverbindungen
Soudage par impulsion électromagnétique - Partie 2 : Conception des assemblages
soudés
Ta slovenski standard je istoveten z: EN 18007-2:2024
ICS:
25.160.10 Varilni postopki in varjenje Welding processes
25.160.40 Varjeni spoji in vari Welded joints and welds
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN 18007-2
EUROPEAN STANDARD
NORME EUROPÉENNE
July 2024
EUROPÄISCHE NORM
ICS 25.160.10; 25.160.40
English Version
Electromagnetic pulse welding - Part 2: Design of welded
joints
Soudage par impulsion électromagnétique - Partie 2 : Elektromagnetisches Pulsschweißen - Teil 2:
Conception des assemblages soudés Ausführung der Schweißverbindungen
This European Standard was approved by CEN on 7 June 2024.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 18007-2:2024 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Design requirements . 5
4.1 Documentation . 5
4.2 Joint design . 5
4.2.1 General. 5
4.2.2 Welding of sheet metal parts . 6
4.2.3 Welding of cylindrical parts . 7
4.3 Additional information . 8
4.3.1 General specifications . 8
4.3.2 Weldment dimensions . 8
4.3.3 Welding operator qualification . 8
4.3.4 Welding procedure qualification . 8
4.3.5 Inspection . 8
European foreword
This document (EN 18007-2:2024) has been prepared by Technical Committee CEN/TC 121 “Welding
and allied processes”, the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by January 2025, and conflicting national standards shall
be withdrawn at the latest by January 2025.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
The EN 18007 series of standards, under the general title Electromagnetic pulse welding, consists of the
following parts:
— Part 1: Welding knowledge, terminology and vocabulary,
— Part 2: Design of welded joints,
— Part 3: Qualification of welding operators and weld setters,
— Part 4: Specification and qualification of welding procedures,
— Part 5: Quality and inspection requirements.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Ne
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.