CEN/TS 17307:2019

Material derived from End-of-Life tyres - Granulates and powders - Elastomers identification: Gas-chromatography and mass-spectrometric detection of pyrolysis products in solution

This document specifies a method for the identification of the elastomers in granulates or powder derived from End-of-Life Tyres.
The method specified is a qualitative method only.

Material aus Altreifen - Granulat und Mehle - Identifizierung von Elastomeren: Gaschromatographie und massenspektrometrische Detektion von Pyrolyseprodukten in Lösung

Dieses Dokument legt ein Verfahren zur Identifikation von Elastomeren in Granulaten oder Mehl aus Altreifen fest.
Das festgelegte Verfahren stellt lediglich ein qualitatives Verfahren dar.

Matériaux obtenus à partir de pneumatiques en fin de vie - Granulats et poudrette - Identification des élastomères : Détection par chromatographie en phase gazeuse et spectrométrie de masse des produits de pyrolyse en solution

Le présent document spécifie une méthode pour l'identification des élastomères dans les granulats ou la poudrette provenant de pneumatiques usagés non réutilisables.
La méthode spécifiée est uniquement qualitative.

Snov iz izrabljenih avtomobilskih gum - Granulati in praški - Identifikacija elastomerov: odkrivanje piroliznih produktov v raztopinah z uporabo plinske kromatografije in masne spektrometrije

Ta dokument določa metodo za identifikacijo elastomerov v granulatih ali prašku iz izrabljenih avtomobilskih gum.
Določena je zgolj kvalitativna metoda.

General Information

• Status: Published
• Publication Date: 26-Mar-2019
• ICS: 83.160.01 - Tyres in general
• Technical Committee: CEN/TC 366 - Project Committe - Tyre recycling
• Drafting Committee: CEN/TC 366/WG 3 - Composition characteristics
• Current Stage: 9060 - Closure of 2 Year Review Enquiry - Review Enquiry
• Start Date: 02-Sep-2022
• Completion Date: 02-Sep-2022
• Ref Project: SIST-TS CEN/TS 17307:2019 - Material derived from End-of-Life tyres - Granulates and powders - Elastomers identification: Gas-chromatography and mass-spectrometric detection of pyrolysis products in solution

Standards Content (Sample)

SLOVENSKI STANDARD
01-junij-2019
Snov iz izrabljenih avtomobilskih gum - Granulati in praški - Identifikacija
elastomerov: odkrivanje piroliznih produktov v raztopinah z uporabo plinske
kromatografije in masne spektrometrije
Material derived from End-of-Life tyres - Granulates and powders - Elastomers
identification: Gas-chromatography and mass-spectrometric detection of pyrolysis
products in solution
Material aus Altreifen - Granulat und Mehle - Identifizierung von Elastomeren:
Gaschromatographie und massenspektrometrische Detektion von Pyrolyseprodukten in
Lösung
Matériaux obtenus à partir de pneumatiques en fin de vie - Granulats et poudrette -
Identification des élastomères : Détection par chromatographie en phase gazeuse et
spectrométrie de masse des produits de pyrolyse en solution
Ta slovenski standard je istoveten z: CEN/TS 17307:2019
ICS:
71.040.50 Fizikalnokemijske analitske Physicochemical methods of
metode analysis
83.160.01 Avtomobilske pnevmatike na Tyres in general
splošno
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

CEN/TS 17307
TECHNICAL SPECIFICATION
SPÉCIFICATION TECHNIQUE
March 2019
TECHNISCHE SPEZIFIKATION
ICS 83.160.01
English Version
Material derived from End-of-Life tyres - Granulates and
powders - Elastomers identification: Gas-chromatography
and mass-spectrometric detection of pyrolysis products in
solution
Matériaux obtenus à partir de pneumatiques en fin de Material aus Altreifen - Granulat und Mehle -
vie - Granulats et poudrette - Identification des Identifizierung von Elastomeren: Gaschromatographie
élastomères : Détection par chromatographie en phase und massenspektrometrische Detektion von
gazeuse et spectrométrie de masse des produits de Pyrolyseprodukten in Lösung
pyrolyse en solution
This Technical Specification (CEN/TS) was approved by CEN on 14 January 2019 for provisional application.

The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to
submit their comments, particularly on the question whether the CEN/TS can be converted into a European Standard.

CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS
available promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in
parallel to the CEN/TS) until the final decision about the possible conversion of the CEN/TS into an EN is reached.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TS 17307:2019 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Principle . 5
5 Reagents . 5
6 Apparatus . 5
7 Procedure. 7
8 Interpretation of the GC/MS data . 8

European foreword
This document (CEN/TS 17307:2019) has been prepared by Technical Committee CEN/TC 366
“Materials obtained from End-of-Life Tyres (ELT)”, the secretariat of which is held by UNI.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN/CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to announce this Technical Specification: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Introduction
WARNING — Persons using this Euopean Standard should be familiar with normal laboratory
practice. This standard does not purport to address all of the safety problems, if any, associated
with its use. It is the responsibility of the user to establish appropriate safety and health
practices and to ensure compliance with any national regulatory conditions.
1 Scope
This document specifies a method for the identification of the elastomers in granulates or powder
derived from End-of-Life Tyres.
The method specified is a qualitative method only.
2 Normative references
The following documents are referred
...