EN ISO 16321-1:2022/A1:2024
(Amendment)Eye and face protection for occupational use - Part 1: General requirements - Amendment 1 (ISO 16321-1:2021/FDAM 1:2024)
Eye and face protection for occupational use - Part 1: General requirements - Amendment 1 (ISO 16321-1:2021/FDAM 1:2024)
Augen- und Gesichtsschutz für berufliche Anwendungen - Teil 1: Allgemeine Anforderungen - Änderung 1 (ISO 16321-1:2021/FDAM 1:2024)
No scope available
Protection des yeux et du visage à usage professionnel - Partie 1: Exigences générales - Amendement 1 (ISO 16321-1:2021/FDAM 1:2024)
Zaščita za oči in obraz za poklicno uporabo - 1. del: Splošne zahteve - Dopolnilo A1 (ISO 16321-1:2021/FDAM 1:2024)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 16321-1:2022/oprA1:2023
01-marec-2023
Zaščita za oči in obraz za poklicno uporabo - 1. del: Splošne zahteve - Dopolnilo
A1 (ISO 16321-1:2021/DAM 1:2023)
Eye and face protection for occupational use - Part 1: General requirements -
Amendment 1 (ISO 16321-1:2021/DAM 1:2023)
Protection des yeux et du visage à usage professionnel - Partie 1 : Exigences générales
- Amendement 1 (ISO 16321-1:2021/DAM 1:2023)
Ta slovenski standard je istoveten z: EN ISO 16321-1:2022/prA1
ICS:
13.340.20 Varovalna oprema za glavo Head protective equipment
SIST EN ISO 16321-1:2022/oprA1:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
SIST EN ISO 16321-1:2022/oprA1:2023
SIST EN ISO 16321-1:2022/oprA1:2023
DRAFT AMENDMENT
ISO 16321-1:2021/DAM 1
ISO/TC 94/SC 6 Secretariat: BSI
Voting begins on: Voting terminates on:
2023-01-10 2023-04-04
Eye and face protection for occupational use —
Part 1:
General requirements
AMENDMENT 1
Protection des yeux et du visage à usage professionnel —
Partie 1: Exigences générales
AMENDEMENT 1
ICS: 13.340.20
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO 16321-1:2021/DAM 1:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023
SIST EN ISO 16321-1:2022/oprA1:2023
ISO 16321-1:2021/DAM 1:2023(E)
DRAFT AMENDMENT
ISO 16321-1:2021/DAM 1
ISO/TC 94/SC 6 Secretariat: BSI
Voting begins on: Voting terminates on:
Eye and face protection for occupational use —
Part 1:
General requirements
AMENDMENT 1
Protection des yeux et du visage à usage professionnel —
Partie 1: Exigences générales
AMENDEMENT 1
ICS: 13.340.20
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
© ISO 2023
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
NOT BE REFERRED TO AS AN INTERNATIONAL
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on STANDARD UNTIL PUBLISHED AS SUCH.
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
IN ADDITION TO THEIR EVALUATION AS
or ISO’s member body in the country of the requester. BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
ISO copyright office
USER PURPOSES, DRAFT INTERNATIONAL
CP 401 • Ch. de Blandonnet 8
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
CH-1214 Vernier, Geneva
POTENTIAL TO BECOME STANDARDS TO
Phone: +41 22 749 01 11
WHICH REFERENCE MAY BE MADE IN
Reference number
Email: copyright@iso.org
NATIONAL REGULATIONS.
Website: www.iso.org ISO 16321-1:2021/DAM 1:2022(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
Published in Switzerland
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
ii
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2022
SIST EN ISO 16321-1:2022/oprA1:2023
ISO 16321-1:2021/DAM 1:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see the following
URL: www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 94, Personal safety — Personal protective
equipment, Subcommittee SC 6, Eye and face protection.
A list of all parts in the ISO 16321 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iii
SIST EN ISO 16321-1:2022/oprA1:2023
SIST EN ISO 16321-1:2022/oprA1:2023
ISO 16321-1:2021/DAM 1:2022(E)
Eye and face protection for occupational use —
Part 1:
General requirements
AMENDMENT 1
Scope
Add at the end of the second paragraph:
Part 4 provides requirements and guidance on protectors against biological hazards .
With the footnote:
In preparation.
Field of view
5.1
Replace the two paragraphs with:
Excluding face shields and eye shields mounted on another item of PPE that restricts the field of view,
e.g., a protective helmet, protectors, when in the as-worn position and measured at the corneal apices
of the headform in accordance with ISO 18526-3:2020, 6.2, shall have a minimum unobstructed field of
view in front of each eye of 30° temporally and nasally in the horizontal meridian, and 30° superiorly
and inferiorly in the vertical meridian.
Face shields and eye shields mounted on another item of PPE that restricts the field of view, when
in the as-worn position and measured at the corneal apices of the headform in accordance with
ISO 18526-3:2020, 6.2, shall have a minimum unobstructed field of view in front of each eye of 30°
temporally and nasally in the horizontal meridian, and
— a minimum field of view in the superior direction of no less than 1° smaller than that provided by
any field of view requirements for the helmet or other PPE, and
— a minimum field of view in the inferior direction of 30°, and
— a minimum field of view in the vertical direction (superior and inferior combined) of 60°.
Protectors used for driving shall have a minimum unobstructed field of view in front of each eye of 60°
temporally and 30° nasally in the horizontal meridian and 30° superiorly and inferiorly in the vertical
meridian, when measured at the corneal apices of the headform in accordance with ISO 18526-3:2020,
6.2.
Luminous and spectral transmittance and scale numbers – Table 1
6.3.3.2 – Headers in Table 1 – Amend the headers in columns 3 and 4, row 4
SIST EN ISO 16321-1:2022/oprA1:2023
ISO 16321-1:2021/DAM 1:2022(E)
Optional
Scale Visible
Wavelength range from 280 nm to 400 nm infrared spec-
number spectral range
tral range
Maximum Maximum Maximum Luminous Maximum
solar UV-B solar UV-A trans- mean 380 nm to transmittance solar IR
transmittance mittance 400 nm trans- transmit-
mittance tance
τ τ τ τ τ
SUVB SUVA 380 m380-400 v,D65 SIR
280 nm ≤ λ 315 nm ≤ λ 380 nm ≤ λ 380 nm ≤ λ 780 nm ≤ λ
≤ 315 nm ≤ 380 nm ≤ 400 nm ≤ 780 nm ≤ 2 000 nm
(%) (%) (%) (%) (%)
Marking of sunglare filters
6.3.3.3
Replace the text with:
Sunglare filters that meet the mandatory transmittance requirements given in Table 8 shall be marked
by code letter G. Sunglare filters of shade numbers 0, 1, 2 or 3 shall compl
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.