EN 13476-1:2018
(Main)Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 1:General requirements and performance characteristics
Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 1:General requirements and performance characteristics
This European Standard, together with EN 13476 2 and EN 13476 3, specifies the definitions and general requirements for pipes, fittings and the system based on unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) structured-wall piping systems that are to be used for non-pressure underground drainage and sewerage systems.
This standard is applicable to:
a) structured-wall pipes and fittings, which are to be used buried in the ground outside a building structure only; reflected by the marking of products by "U";
b) structured-wall pipes and fittings, which are to be used buried in ground both outside (application area code "U") and within a building structure (application area code "D"); reflected in the marking of products by "UD".
In conjunction with EN 13476 2 and EN 13476 3, it is applicable to structured-wall pipes and fittings with or without an integral socket with elastomeric ring seal joints, as well as welded and fused joints.
This part specifies general aspects and gives guidance concerning a national selection of requirement levels and classes where part 2 and part 3 of this standard provide options.
EN 13476 2 and EN 13476 3 specify material characteristics, dimensions and tolerances, test methods, test parameters and requirements for pipes with smooth internal and external surfaces, Type A, and pipes with smooth internal and profiled external surfaces, Type B.
This standard, together with EN 13476 2 and EN 13476 3, covers a range of pipe and fitting sizes, materials, pipe constructions, stiffness classes and tolerance classes and offers recommendations concerning colours.
NOTE 1 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
NOTE 2 Pipes, fittings and other components conforming to any plastic product standards referred to in Clause 2 can be used with pipes and fittings conforming to this standard, when they conform to the requirements for joint dimensions given in part 2 and part 3 of this standard and to the performance requirements given in Clause 9.
Kunststoff-Rohrleitungssysteme für erdverlegte drucklose Abwasserkanäle und -leitungen - Rohrleitungssysteme mit profilierter Wandung aus weichmacherfreiem Polyvinylchlorid (PVC-U), Polypropylen (PP) und Polyethylen (PE) - Teil 1: Allgemeine Anforderungen und Leistungsmerkmale
Diese Europäische Norm legt gemeinsam mit EN 13476-2 und EN 13476-3 Definitionen und allgemeine Anforderungen an Rohre, Formstücke und das Rohrleitungssystem aus weichmacherfreiem Polyvinylchlorid (PVC-U), Polypropylen (PP) und Polyethylen (PE) mit profilierter Wandung fest, die für erdverlegte, drucklos betriebene Abwasserkanäle und leitungen verwendet werden.
Diese Norm gilt für:
a) Rohre und Formstücke mit profilierter Wandung, die ausschließlich für erdverlegte Anwendungen außerhalb einer Gebäudestruktur vorgesehen sind; gekennzeichnet mit Anwendungs¬kennzeichen "U";
b) Rohre und Formstücke mit profilierter Wandung, die sowohl für erdverlegte Anwendungen außerhalb der Gebäudestruktur (Anwendungskennzeichen "U") als auch innerhalb einer Gebäudestruktur (Anwendungskennzeichen "D") vorgesehen sind; gekennzeichnet mit Anwendungs¬kennzeichen "UD".
Gemeinsam mit EN 13476-2 und EN 13476-3 gilt dieser Teil für Rohre und Formstücke mit profilierter Wandung sowohl mit glatten Enden als auch mit angeformter Muffe mit elastomeren Dichtringverbindungen bzw. Verbindung durch Heizelement-Stumpf-, Extrusions- oder Heizwendelschweißen.
Dieser Teil legt allgemeine Aspekte fest und enthält Empfehlungen zur Auswahl nationaler Anforderungsstufen und -klassen, wofür Teil 2 und Teil 3 dieser Norm die Optionen enthält.
EN 13476-2 und EN 13476-3 legen Werkstoffeigenschaften, Maße und Toleranzen, Prüfverfahren, Prüfparameter und Anforderungen für Rohre mit glatten Innen- und Außenflächen, Typ A, sowie Rohre mit glatten Innen- und profilierten Außenflächen, Typ B, fest.
Diese Norm enthält, gemeinsam mit EN 13476-2 und EN 13476-3, Festlegungen für Maße von Rohren und Formstücken, für Werkstoffe, Rohrkonstruktionen, für Steifigkeitsklassen und Toleranzklassen und gibt Empfehlungen für die Einfärbung.
ANMERKUNG 1 Der Käufer bzw. Auftraggeber ist unter Berücksichtigung der eigenen Anforderungen sowie der geltenden nationalen Festlegungen und Verlegepraktiken oder -vorschriften für die entsprechende Auswahl dieser Kriterien verantwortlich.
ANMERKUNG 2 Rohre, Formstücke und andere Rohrleitungsteile, die einer der in Abschnitt 2 aufgeführten Anwendungs¬normen für Kunststoff-Rohrleitungssysteme entsprechen, können mit Rohren und Formstücken nach dieser Norm verwendet werden, sofern sie die Anforderungen an die Anschlussmaße nach Teil 2 und Teil 3 dieser Norm und die Anforderungen an die Gebrauchstauglichkeit nach Abschnitt 9 erfüllen.
Systèmes de canalisations en plastique pour les branchements et les collecteurs d'assainissements sans pression enterrés - Systèmes de canalisations à parois structurées en poly(chlorure de vinyle) non plastifié (PVC-U), polypropylène (PP) et polyéthylène (PE) - Partie 1: Exigences générales et caractéristiques de performance
La présente Norme européenne, conjointement à l'EN 13476 2 et l'EN 13476 3, spécifie les définitions et les exigences générales pour les tubes, les raccords et le système pour des systèmes de canalisations à parois structurées en poly(chlorure de vinyle) non plastifié (PVC U), polypropylène (PP) et polyéthylène (PE), destinés à être utilisés dans des systèmes de branchements et de collecteurs d’assainissement enterrés sans pression.
La présente norme s’applique aux :
a) tubes et raccords à parois structurées, destinés à être utilisés enterrés à l’extérieur du bâtiment uniquement ; ce qui est reflété au niveau du marquage des produits par « U » ;
b) tubes et raccords à parois structurées, destinés à être utilisés enterrés, aussi bien à l’extérieur (code de la zone d’application « U ») qu’à l’intérieur de la structure des bâtiments (code de la zone d’application « D ») ; ce qui est reflété au niveau du marquage des produits par « UD ».
Conjointement à l'EN 13476 2 et l'EN 13476 3, elle s’applique aux tubes et raccords à parois structurées avec ou sans emboîture intégrée avec des assemblages à bague d’étanchéité en élastomère ainsi que des assemblages soudés et les assemblages obtenus par fusion.
La présente partie spécifie des aspects généraux et fournit des préconisations concernant une sélection nationale des niveaux et classes d’exigences alors que la partie 2 et la partie 3 de la présente norme prévoient des options.
L'EN 13476 2 et l'EN 13476 3 spécifient les caractéristiques de la matière, les dimensions et les tolérances, les méthodes d’essai, les paramètres d’essai et les exigences applicables aux tubes avec une surface interne et une surface externe lisses, de Type A, et aux tubes avec une surface interne lisse et une surface externe profilée, de Type B.
La présente norme, conjointement à l'EN 13476 2 et l'EN 13476 3, couvre une gamme de dimensions de tubes et de raccords, de matières, de constructions de tube, de classes de rigidité et de classes de tolérance et donne des recommandations concernant les couleurs.
NOTE 1 Il est de la responsabilité de l’acheteur ou du concepteur du réseau de faire les sélections appropriées à partir de ces aspects, en tenant compte des exigences particulières et des règles nationales et des pratiques ou codes de pose pertinents.
NOTE 2 Les tubes, raccords et autres composants conformes aux normes de produits plastiques indiquées à l’Article 2 peuvent être utilisés avec des tubes et des raccords conformes à la présente norme, lorsqu’ils satisfont aux exigences dimensionnelles des assemblages indiquées dans la partie 2 et la partie 3 de la présente norme et aux exigences de performance indiquées à l’Article 9.
Cevni sistemi iz polimernih materialov za odvodnjavanje in kanalizacijo, ki delujejo po težnostnem principu in so položeni v zemljo - Cevni sistemi s strukturirano steno iz nemehčanega polivinilklorida (PVC-U), polipropilena (PP) in polietilena (PE) - 1. del: Splošne zahteve in zahtevane lastnosti
Ta evropski standard skupaj s standardoma EN 13476 2 in EN 13476 3 določa definicije in splošne zahteve za cevi, fitinge in sistem, ki temelji na nemehčanih cevnih sistemih iz polivinilklorida (PVC-U), polipropilena (PP) ter polietilena (PE) v strukturiranih stenah, ki se uporabljajo za podzemne sisteme za odvodnjavanje in kanalizacijo, ki delujejo brez tlaka.
Ta standard se uporablja za:
a) cevi in fitinge v strukturiranih stenah, ki se bodo uporabljali izključno zakopani v tla zunaj zgradbe; na proizvodu je oznaka »U«;
b) cevi in fitinge v strukturiranih stenah, ki se bodo uporabljali zakopani v tla tako zunaj (koda območja uporabe »U«) kot znotraj zgradbe (koda območja uporabe »D«); na proizvodu je oznaka »UD«.
Skupaj s standardoma EN 13476 2 in EN 13476 3 se uporablja za cevi in fitinge v strukturiranih stenah z oglavkom ali brez njega s spoji elastomernih tesnilnih obročev ter varjenimi in fuzijskimi spoji.
Ta del določa splošne vidike in podaja smernice v zvezi z nacionalno izbiro ravni in razredov zahtev, pri čemer 2. in 3. del tega standarda podajata možnosti.
Standarda EN 13476 2 in EN 13476 3 določata značilnosti materiala, mere in tolerance, preskusne metode, preskusne parametre ter zahteve za cevi z gladkimi notranjimi in zunanjimi površinami (tip A) ter cevi z gladkimi notranjimi in profiliranimi zunanjimi površinami (tip B).
Ta standard skupaj s standardoma EN 13476 2 in EN 13476 3 zajema razpon velikosti cevi in fitingov, materiale, cevne konstrukcije, razrede togosti in razrede tolerance ter ponuja priporočila v zvezi z barvami.
OPOMBA 1: Za ustrezno izbiro teh vidikov je odgovoren kupec ali projektant, pri čemer mora upoštevati posebne zahteve ter vse pomembne nacionalne predpise in prakse ali kodekse vgradnje.
OPOMBA 2: Cevi, fitingi in drugi sestavni deli, ki so skladni s katerim koli standardom za plastični proizvod iz točke 2, se lahko uporabljajo s cevmi in fitingi, ki so skladni s tem standardom, če izpolnjujejo zahteve v zvezi z velikostmi spojev iz 2. in 3. dela tega standarda ter zahteve glede zmogljivosti iz točke 9.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.VWUXNWXULUDQRKunststoff-Rohrleitungssysteme für erdverlegte drucklose Abwasserkanäle und -leitungen - Rohrleitungssysteme mit profilierter Wandung aus weichmacherfreiem Polyvinylchlorid (PVC-U), Polypropylen (PP) und Polyethylen (PE) - Teil 1: Allgemeine Anforderungen und LeistungsmerkmalePlastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 1:General requirements and performance characteristics01-junij-2018SIST EN 13476-1:2018SLOVENSKI
STANDARDSIST EN 13476-1:20071DGRPHãþD
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Systèmes de canalisations en plastiques pour les branchements et les collecteurs d'assainissements sans pression enterrés - Systèmes de canalisation à parois structurées en poly(chlorure de vinyle) non plastifié (PVC-U), polypropylène (PP) et polyéthylène (PE) - Partie 1 : Exigences générales et caractéristiques de performance93.030Zunanji sistemi za odpadno vodoExternal sewage systems23.040.05Cevovodi
za zunanje sisteme za odpadno vodo in njihovi deliPipeline and its parts for external sewage systemsICS:SIST EN 13476-1:2018en,fr,deTa slovenski standard je istoveten z:EN 13476-1:2018SIST EN 13476-1:2018
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13476-1
April
t r s z ICS
t uä r v rä r sâ
{ uä r u r Supersedes EN
s u v y xæ sã t r r yEnglish Version
Plastics piping systems for nonæpressure underground drainage and sewerage æ Structuredæwall piping systems of and performance characteristics Systèmes de canalisations en plastique pour les branchements et les collecteurs d 5assainissements sans pression enterrés æ Systèmes de canalisations à parois Partie
sã Exigences générales et caractéristiques de performance
KunststoffæRohrleitungssysteme für erdverlegte drucklose Abwasserkanäle und æleitungen æ Rohrleitungssysteme mit profilierter Wandung aus Allgemeine Anforderungen und Leistungsmerkmale This European Standard was approved by CEN on
z February
t r s zä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Rue de la Science 23,
B-1040 Brussels
t r s z CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s u v y xæ sã t r s z ESIST EN 13476-1:2018
Characteristics of PVC-U, PP and PE pipes and fittings . 18 A.1 General . 18 A.2 Material characteristics . 18 A.3 Chemical resistance . 18 A.4 Abrasion resistance . 19 A.5 Hydraulic roughness . 19 Annex B (informative)
Structural design . 20 Annex C (informative)
Designation of pipes and corresponding fittings . 21 Annex D (informative)
Guidance in cleaning plastics pipes . 22 D.1 Introduction . 22 SIST EN 13476-1:2018
Note 1 to entry: For Type B constructions, see EN 13476-3. SIST EN 13476-1:2018
nominal angle of fitting DN nominal size DN/ID nominal size related to inside diameter DN/OD nominal size related to outside diameter PE polyethylene PP polypropylene SIST EN 13476-1:2018
...
Frequently Asked Questions
EN 13476-1:2018 is a standard published by the European Committee for Standardization (CEN). Its full title is "Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 1:General requirements and performance characteristics". This standard covers: This European Standard, together with EN 13476 2 and EN 13476 3, specifies the definitions and general requirements for pipes, fittings and the system based on unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) structured-wall piping systems that are to be used for non-pressure underground drainage and sewerage systems. This standard is applicable to: a) structured-wall pipes and fittings, which are to be used buried in the ground outside a building structure only; reflected by the marking of products by "U"; b) structured-wall pipes and fittings, which are to be used buried in ground both outside (application area code "U") and within a building structure (application area code "D"); reflected in the marking of products by "UD". In conjunction with EN 13476 2 and EN 13476 3, it is applicable to structured-wall pipes and fittings with or without an integral socket with elastomeric ring seal joints, as well as welded and fused joints. This part specifies general aspects and gives guidance concerning a national selection of requirement levels and classes where part 2 and part 3 of this standard provide options. EN 13476 2 and EN 13476 3 specify material characteristics, dimensions and tolerances, test methods, test parameters and requirements for pipes with smooth internal and external surfaces, Type A, and pipes with smooth internal and profiled external surfaces, Type B. This standard, together with EN 13476 2 and EN 13476 3, covers a range of pipe and fitting sizes, materials, pipe constructions, stiffness classes and tolerance classes and offers recommendations concerning colours. NOTE 1 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes. NOTE 2 Pipes, fittings and other components conforming to any plastic product standards referred to in Clause 2 can be used with pipes and fittings conforming to this standard, when they conform to the requirements for joint dimensions given in part 2 and part 3 of this standard and to the performance requirements given in Clause 9.
This European Standard, together with EN 13476 2 and EN 13476 3, specifies the definitions and general requirements for pipes, fittings and the system based on unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) structured-wall piping systems that are to be used for non-pressure underground drainage and sewerage systems. This standard is applicable to: a) structured-wall pipes and fittings, which are to be used buried in the ground outside a building structure only; reflected by the marking of products by "U"; b) structured-wall pipes and fittings, which are to be used buried in ground both outside (application area code "U") and within a building structure (application area code "D"); reflected in the marking of products by "UD". In conjunction with EN 13476 2 and EN 13476 3, it is applicable to structured-wall pipes and fittings with or without an integral socket with elastomeric ring seal joints, as well as welded and fused joints. This part specifies general aspects and gives guidance concerning a national selection of requirement levels and classes where part 2 and part 3 of this standard provide options. EN 13476 2 and EN 13476 3 specify material characteristics, dimensions and tolerances, test methods, test parameters and requirements for pipes with smooth internal and external surfaces, Type A, and pipes with smooth internal and profiled external surfaces, Type B. This standard, together with EN 13476 2 and EN 13476 3, covers a range of pipe and fitting sizes, materials, pipe constructions, stiffness classes and tolerance classes and offers recommendations concerning colours. NOTE 1 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes. NOTE 2 Pipes, fittings and other components conforming to any plastic product standards referred to in Clause 2 can be used with pipes and fittings conforming to this standard, when they conform to the requirements for joint dimensions given in part 2 and part 3 of this standard and to the performance requirements given in Clause 9.
EN 13476-1:2018 is classified under the following ICS (International Classification for Standards) categories: 23.040.01 - Pipeline components and pipelines in general; 93.030 - External sewage systems. The ICS classification helps identify the subject area and facilitates finding related standards.
EN 13476-1:2018 has the following relationships with other standards: It is inter standard links to EN 13476-1:2007, EN 13476-1:2025. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
You can purchase EN 13476-1:2018 directly from iTeh Standards. The document is available in PDF format and is delivered instantly after payment. Add the standard to your cart and complete the secure checkout process. iTeh Standards is an authorized distributor of CEN standards.
The article discusses the European Standard EN 13476-1:2018, which provides requirements for structured-wall piping systems made of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) for non-pressure underground drainage and sewerage systems. The standard applies to both buried pipes and fittings used outside buildings (marked as "U") and those used both outside and within buildings (marked as "UD"). It covers various types of joints, including elastomeric ring seal joints, welded joints, and fused joints. The standard provides general guidance and advice on requirement levels and classes, while EN 13476-2 and EN 13476-3 specify material characteristics, dimensions, test methods, and other specific requirements for different types of pipes. The standard also covers a range of sizes, materials, constructions, stiffness classes, tolerance classes, and color recommendations. It is the responsibility of the purchaser or specifier to consider their specific requirements and national regulations when selecting the appropriate components. Other plastic product standards can also be used in conjunction with EN 13476-1, as long as they meet the required joint dimensions and performance requirements.
제목: EN 13476-1:2018 - 비압력 지하 배수 및 하수용 비구조 폴리(vinyl chloride) (PVC-U), 폴리프로필렌 (PP) 및 폴리에틸렌 (PE) 단열 벽 파이프 시스템 - 일반 요구 사항 및 성능 특성 내용: 이 유럽 표준은 EN 13476-2 및 EN 13476-3과 함께 사용되어, 비압력 지하 배수 및 하수용 시스템에 사용되는 폴리(vinyl chloride) (PVC-U), 폴리프로필렌 (PP) 및 폴리에틸렌 (PE) 단열 벽 파이프 및 피팅에 대한 정의 및 일반 요구 사항을 규정합니다. 이 표준은 다음과 같은 경우에 적용됩니다: a) 건축물 구조 외부에만 묻히는 구조 벽 파이프 및 피팅. 표시에 "U"가 있는 제품; b) 건축물 구조 내외부에 묻히는 구조 벽 파이프 및 피팅. 표시에 "UD"가 있는 제품. EN 13476-2 및 EN 13476-3과 함께 사용되며, 실리콘 고무 링 실 쥐어질 링 문질러 연결부와 용접 및 용해 연결부가 있는 구조 벽 파이프 및 피팅에 적용됩니다. 이 부분은 일반적인 측면을 규정하고, 이 표준의 파트 2 및 파트 3에서 옵션을 제공하는 국가 선택 요구 수준 및 클래스에 대한 지침을 제공합니다. EN 13476-2 및 EN 13476-3은 내부와 외부 표면이 부드러운 파이프 유형 A와 내부는 부드럽고 외부는 프로파일링 된 파이프 유형 B에 대한 소재 특성, 치수 및 허용오차, 시험 방법, 시험 매개변수 및 요구 사항을 규정합니다. 이 표준은 다양한 파이프 및 피팅 크기, 소재, 파이프 구조, 강성 등급 및 허용오차 등을 다루며, 색깔에 관한 권고사항도 제공합니다. 참고 1: 특정 요구 사항 및 관련 국가 규정 및 설치 관행 또는 규정을 고려하여 구매자 또는 제시자가 이러한 측면 중 적절한 선택을 해야 합니다. 참고 2: 절 2에서 언급된 모든 플라스틱 제품 표준에 해당하는 파이프, 피팅 및 기타 구성 요소는 이 표준의 파트 2 및 파트 3의 결합 부 관련 요구 사항 및 절 9의 성능 요구 사항을 따를 경우 사용할 수 있습니다.
記事タイトル：EN 13476-1:2018 - 圧力のない地下排水および下水道用のプラスチック配管システム - 無塗膜ポリ塩化ビニル(PVC-U)、ポリプロピレン(PP)、およびポリエチレン(PE)の構造壁配管システム - 第1部：一般要件および性能特性 記事内容：この欧州規格は、EN 13476-2およびEN 13476-3とともに、非圧力地下排水および下水道システムに使用される無塗膜ポリ塩化ビニル(PVC-U)、ポリプロピレン(PP)、およびポリエチレン(PE)の構造壁配管システムに関する定義と一般要件を規定しています。 この規格は次の適用範囲があります： a) 建物構造の外部に埋設される構造壁管および継手。製品のマーキングに「U」が付いています。 b) 建物構造の外部および内部に埋設される構造壁管および継手。製品のマーキングに「UD」が付いています。 EN 13476-2およびEN 13476-3と組み合わせて使用され、エラストマリングシールジョイント付きの統合ソケットを持つ構造壁管および継手、および溶接および溶着継手に適用されます。 この部分は一般的な側面を規定し、この規格のパート2およびパート3がオプションを提供する要件レベルおよびクラスの国内選択に関するガイダンスを提供します。 EN 13476-2およびEN 13476-3は、内部および外部表面が滑らかなタイプAのパイプと、内部が滑らかで外部がプロファイル化されたタイプBのパイプの材料特性、寸法と許容差、試験方法、試験パラメーターおよび要件を規定します。 この規格は、異なるサイズ、材料、パイプ構造、剛性クラス、許容クラスをカバーし、色に関する推奨事項も提供します。 注1：特定の要件および関連する国内規制、取り付け規則またはコードを考慮して、購入者または仕様者がこれらの側面から適切な選択を行う責任があります。 注2：第2節で言及される他のプラスチック製品規格に準拠するパイプ、継手、およびその他の部品は、本規格のパート2およびパート3で示される共結合寸法の要件および第9節で示される性能要件を満たす場合に、本規格と組み合わせて使用できます。
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...