prEN ISO 18563-2

Non-destructive testing - Characterization and verification of ultrasonic phased array equipment - Part 2: Array probes (ISO/DIS 18563-2:2023)

This document specifies the characterization tests performed at the end of the fabrication of an array probe. It defines both methodology and acceptance criteria.
This document is applicable to the following array probes used for ultrasonic non-destructive testing (phased array technique or signal processing technique, e.g. FMC-TFM) in contact technique (with or without a wedge or delay line) or in immersion technique, with centre frequencies in the range 0,5 MHz to 10 MHz:
a) array probes with elements in one direction:
—    1-D-linear array (linear array);
—    1-D-curved array;
—    annular array;
b) array probes with elements in two directions:
—    2-D-array (matrix array);
—    sectorial annular array;
—    partial sectorial annular array.
This document does not give methods and acceptance criteria to characterize the performance of an ultrasonic phased array instrument or the performance of a combined system. These are given in ISO 18563–1 and in ISO 18563–3.

Zerstörungsfreie Prüfung - Charakterisierung und Verifizierung der Ultraschall‑Prüfausrüstung mit Phased‑Arrays - Teil 2: Prüfköpfe (ISO/DIS 18563‑2:2023)

Essais non destructifs - Caractérisation et vérification de l'appareillage de contrôle par ultrasons en multiéléments - Partie 2: Traducteurs multiéléments (ISO/DIS 18563-2:2023)

ISO 18563-2:2017 spécifie les essais de caractérisation effectués à l'issue de la fabrication d'un traducteur multiélément. Il définit à la fois la méthodologie et les critères d'acceptation.
ISO 18563-2:2017 s'applique aux traducteurs multiéléments utilisés pour les essais non destructifs par ultrasons selon la technique par contact (avec ou sans sabot) ou selon la technique par immersion, ayant une fréquence centrale comprise entre 0,5 MHz et 10 MHz:
a) traducteurs non matriciels:
- linéaires;
- encerclants;
- sectoriels annulaires partiels (type «marguerite»);
b) traducteurs matriciels 2D.
ISO 18563-2:2017 ne fournit pas les méthodes et critères d'acceptation permettant de caractériser les performances d'un appareil de contrôle par ultrasons en multiéléments ni celles d'un système complet. Ces performances sont données dans l'ISO 18563‑1 et l'ISO 18563‑3.

Neporušitvene preiskave - Karakterizacija in preverjanje ultrazvočne opreme faznih sistemov - 2. del: Matrične sonde (ISO/DIS 18563-2:2023)

General Information

• Status: Not Published
• Publication Date: 22-Dec-2024
• ICS: 19.100 - Non-destructive testing
• Technical Committee: CEN/TC 138 - Non-destructive testing
• Current Stage: 4599 - Dispatch of FV draft to CMC - Finalization for Vote
• Start Date: 22-Apr-2024
• Completion Date: 22-Apr-2024
• Ref Project: oSIST prEN ISO 18563-2:2024 - Non-destructive testing - Characterization and verification of ultrasonic phased array equipment - Part 2: Array probes (ISO/DIS 18563-2:2023)

Relations

• Revises: EN ISO 18563-2:2017 - Non-destructive testing - Characterization and verification of ultrasonic phased array equipment - Part 2: Probes (ISO 18563-2:2017)
• Effective Date: 22-Feb-2023

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN ISO 18563-2:2024
01-januar-2024
Neporušitvene preiskave - Karakterizacija in preverjanje ultrazvočne opreme
faznih sistemov - 2. del: Matrične sonde (ISO/DIS 18563-2:2023)
Non-destructive testing - Characterization and verification of ultrasonic phased array
equipment - Part 2: Array probes (ISO/DIS 18563-2:2023)
Zerstörungsfreie Prüfung - Charakterisierung und Verifizierung der Ultraschall-
Prüfausrüstung mit Phased-Arrays - Teil 2: Prüfköpfe (ISO/DIS 18563-2:2023)
Essais non destructifs - Caractérisation et vérification de l'appareillage de contrôle par
ultrasons en multiéléments - Partie 2: Traducteurs multiéléments (ISO/DIS 18563-
2:2023)
Ta slovenski standard je istoveten z: prEN ISO 18563-2
ICS:
19.100 Neporušitveno preskušanje Non-destructive testing
oSIST prEN ISO 18563-2:2024 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 18563-2:2024

---------------------- Page: 2 ----------------------
oSIST prEN ISO 18563-2:2024
DRAFT INTERNATIONAL STANDARD
ISO/DIS 18563-2
ISO/TC 135/SC 3 Secretariat: DIN
Voting begins on: Voting terminates on:
2023-11-17 2024-02-09
Non-destructive testing — Characterization and
verification of ultrasonic phased array equipment —
Part 2:
Array probes
ICS: 19.100
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 18563-2:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023

---------------------- Page: 3 ----------------------
oSIST prEN ISO 18563-2:2024
ISO/DIS 18563-2:2023(E)
DRAFT INTERNATIONAL STANDARD
ISO/DIS 18563-2
ISO/TC 135/SC 3 Secretariat: DIN
Voting begins on: Voting terminates on:

Non-destructive testing — Characterization and
verification of ultrasonic phased array equipment —
Part 2:
Array probes
ICS: 19.100
This document is circulated as received from the committee secretariat.
COPYRIGHT PROTECTED DOCUMENT
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
© ISO 2023
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
NOT BE REFERRED TO AS AN INTERNATIONAL
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on STANDARD UNTIL PUBLISHED AS SUCH.
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
IN ADDITION TO THEIR EVALUATION AS
or ISO’s member body in the country of the requester. BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
ISO copyright office
USER PURPOSES, DRAFT INTERNATIONAL
CP 401 • Ch. de Blandonnet 8
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
CH-1214 Vernier, Geneva
POTENTIAL TO BECOME STANDARDS TO
Phone: [phone]
WHICH REFERENCE MAY BE MADE IN
Reference number
Email: [e-mail]
NATIONAL REGULATIONS.
Website: www.iso.org ISO/DIS 18563-2:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
Published in Switzerland
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
ii
  © ISO 2023 – All rights reserved
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023

---------------------- Page: 4 ----------------------
oSIST prEN ISO 18563-2:2024
ISO/DIS 18563-2:2023(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions .
...