EN ISO 7963:2022
(Main)Non-destructive testing - Ultrasonic testing - Specification for calibration block No. 2 (ISO 7963:2022)
Non-destructive testing - Ultrasonic testing - Specification for calibration block No. 2 (ISO 7963:2022)
This document specifies the requirements for the dimensions, material, manufacture and methods of use for calibration block No. 2 for setting and checking ultrasonic test equipment.
Zerstörungsfreie Prüfung - Ultraschallprüfung - Beschreibung des Kalibrierkörpers Nr. 2 (ISO 7963:2022)
Dieses Dokument legt die Anforderungen an die Maße, den Werkstoff, die Herstellung und die Verfahren zur Verwendung des Kalibrierkörpers Nr. 2 zum Einstellen und zur Überprüfung von Ultraschallprüfausrüstung fest.
Essais non destructifs - Contrôle par ultrasons - Spécifications relatives au bloc d’étalonnage n° 2 (ISO 7963:2022)
Le présent document spécifie les exigences relatives aux dimensions, au matériau et à la fabrication et les méthodes d’utilisation du bloc d’étalonnage n° 2 pour le réglage et la vérification de l’équipement de contrôle par ultrasons.
Neporušitveno preskušanje - Ultrazvočno preskušanje - Specifikacije za umeritveni vzorec št. 2 (ISO 7963:2022)
Ta dokument določa zahteve glede mer, materialov in izdelave ter metode uporabe za umeritveni vzorec št. 2 za nastavitev in preverjanje ultrazvočne preskusne opreme.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-januar-2023
Nadomešča:
SIST EN ISO 7963:2011
Neporušitveno preskušanje - Ultrazvočno preskušanje - Specifikacije za
umeritveni vzorec št. 2 (ISO 7963:2022)
Non-destructive testing - Ultrasonic testing - Specification for calibration block No. 2 (ISO
7963:2022)
Zerstörungsfreie Prüfung – Ultraschallprüfung – Beschreibung des Kalibrierkörpers Nr.2
(ISO 7963:2022)
Essais non destructifs - Contrôle par ultrasons - Spécifications relatives au bloc
d’étalonnage n° 2 (ISO 7963:2022)
Ta slovenski standard je istoveten z: EN ISO 7963:2022
ICS:
19.100 Neporušitveno preskušanje Non-destructive testing
25.160.40 Varjeni spoji in vari Welded joints and welds
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 7963
EUROPEAN STANDARD
NORME EUROPÉENNE
November 2022
EUROPÄISCHE NORM
ICS 25.160.40 Supersedes EN ISO 7963:2010
English Version
Non-destructive testing - Ultrasonic testing - Specification
for calibration block No. 2 (ISO 7963:2022)
Essais non destructifs - Contrôle par ultrasons - Zerstörungsfreie Prüfung - Ultraschallprüfung -
Spécifications relatives au bloc d'étalonnage n° 2 (ISO Beschreibung des Kalibrierkörpers Nr.2 (ISO
7963:2022) 7963:2022)
This European Standard was approved by CEN on 31 August 2022.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 7963:2022 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 7963:2022) has been prepared by Technical Committee ISO/TC 135 "Non-
destructive testing" in collaboration with Technical Committee CEN/TC 138 “Non-destructive testing”
the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by May 2023, and conflicting national standards shall be
withdrawn at the latest by May 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 7963:2010.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 7963:2022 has been approved by CEN as EN ISO 7963:2022 without any modification.
INTERNATIONAL ISO
STANDARD 7963
Third edition
2022-10
Non-destructive testing — Ultrasonic
testing — Specification for calibration
block No. 2
Essais non destructifs — Contrôle par ultrasons — Spécifications
relatives au bloc d’étalonnage n° 2
Reference number
ISO 7963:2022(E)
ISO 7963:2022(E)
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 7963:2022(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Manufacture . 1
4.1 Steel . 1
4.2 Dimensions . 1
4.3 Machining, heat treatment and surface finish . 2
4.4 Reference marks . 3
5 Methods of use .4
5.1 Setting of the time base . 4
5.1.1 General . 4
5.1.2 Setting of the time base up to 125 mm steel with a straight-beam probe . 4
5.1.3 Setting of the time base for 100 mm or 125 mm steel with a miniature
angle-beam probe . 4
5.2 Sensitivity setting and probe checking . 5
5.2.1 General . 5
5.2.2 Sensitivity setting with a straight-beam probe . 5
5.2.3 Miniature angle-beam probes . 6
6 Declaration of conformity . 7
Bibliography . 9
iii
ISO 7963:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 135, Non-destructive testing,
Subcommittee SC 3, Ultrasonic testing in collaboration with the European Committee for Standardization
(CEN) Technical Committee CEN/TC 138, Non-destructive testing, in accordance with the Agreement on
technical cooperation between ISO and CEN (Vienna Agreement).
This third edition cancels and replaces the second edition (ISO 7963:2006), which has been technically
revised.
The main changes are as follows:
— document structure aligned with ISO 2400;
— normative references updated;
— wording updated;
— Annex A deleted and the relevant information shifted to the main text;
— Figures 1, 3 and 6 corrected;
— tempering aligned with ISO 2400.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
ISO 7963:2022(E)
Introduction
Calibration block No. 2 is made of steel and may be used for all ultrasonic testing, as calibration
block No. 1 described in ISO 2400.
Calibration block No. 2 differs in size and shape from calibration block No.1 but is made from the same
material.
Calibration block No. 2 is much smaller and lighter, and its geometry is much simpler than block No 1.
Calibration block No. 2 does not offer as much scope as the larger block No.1; in particular it is not
meant to check an ultrasonic instrument completely.
However, calibration block No. 2 makes it possible, during practical testing, to check simply, from time
to time, the setting of the time base and the sensitivity of the ultrasonic instrument. Moreover, it is
suited to check the beam angle and the probe index point of miniature angle-beam probes.
The International Institute of Welding (IIW) and its members developed the designs of steel calibration
blocks in the 1950s and 1960s which were originally indicated as “IIW calibration block 1” and
“IIW calibration block 2”. These designs have been adopted widely and they form the basis of many
blocks currently available.
The smaller type block is sometimes indicated as “Rompas block” or “miniature angle-beam block
(MAB)”, respectively named after the original Dutch designer or the intended use.
Some commercially available blocks look similar to calibration block No. 2, however
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.