EN ISO 11681-2:2006

Machinery for forestry - Portable chain-saw safety requirements and testing - Part 2: Chain-saws for tree service (ISO 11681-2:2006)

This part of ISO 11681 specifies safety requirements and their verification for the design and construction of portable combustion-engine, hand-held chain-saws for tree service, having a maximum mass, without guide bar or saw chain and with tanks empty, equal to 4,3 kg, and designed for use by a trained operator for pruning and dismantling standing tree crowns. It gives methods for the elimination or reduction of hazards arising from the use of the chain-saws. In addition, it specifies the type of information on safe working practices to be provided by the manufacturer. It deals with all significant hazards. The environmental aspects, except for noise, have not been considered. Chain-saws covered by this part of ISO 11681 are designed to be operated with the right hand on the rear handle and the left hand on the front handle by persons having read and understood the safety requirements in the instruction handbook and using the appropriate personal protective equipment (PPE). This part of ISO 11681 is not applicable to chain-saws manufactured before its date of publication.

Forstmaschinen - Sicherheitstechnische Anforderungen und Prüfungen für tragbare Kettensägen - Teil 2: Kettensägen für die Baumpflege (ISO 11681-2:2006)

Dieser Teil von ISO 11681 spezifiziert die signifikanten Gefährdungen und sicherheitstechnischen Anforderungen und deren Feststellung der Übereinstimmung für die Gestaltung und die Konstruktion von tragbaren, handgehaltenen Kettensägen mit Antrieb durch Verbrennungsmotor für die Baumpflege mit einer maximalen Masse ohne Führungsschiene und Kette und mit leeren Tanks bis 4,3 kg einschließlich, die für einen in der Anwendung ausgebildeten Benutzer zum Entasten und Absägen stehender Baumkronen ausgelegt sind.
Er legt Verfahren zur Vermeidung oder Verminderung der sich aus dem Gebrauch der Kettensägen ergebenden Gefährdungen fest. Außerdem enthält er Informationen über sicheres Arbeiten, die vom Hersteller zur Verfügung zu stellen sind.
Er behandelt alle signifikanten Gefährdungen. Die Gefährdung der Umwelt wird nicht in Betracht gezogen.
Die von diesem Teil der ISO 11681 erfassten Kettensägen sind bestimmt für Arbeiten mit der rechten Hand am hinteren Handgriff und der linken Hand am vorderen Handgriff durch Personen, die die Sicherheitsanweisungen in der Betriebsanleitung gelesen und verstanden haben und entsprechende persönliche Schutzkleidung (PSA) tragen.
Dieser Teil der ISO 11681 gilt nicht für Kettensägen, die vor dem Ausgabedatum dieses Teils hergestellt wurden.

Matériel forestier - Exigences de sécurité et essais des scies à chaîne portatives - Partie 2: Scies à chaîne pour l'élagage des arbres (ISO 11681-2:2006)

Gozdarski stroji - Zahteve za prenosne motorne verižne žage in preskušanje - 2. del: Žage za nego dreves (ISO/DIS 11681-2:2004)

General Information

• Status: Withdrawn
• Publication Date: 30-Jun-2006
• Withdrawal Date: 04-Nov-2008
• ICS: 65.060.80 - Forestry equipment
• Technical Committee: CEN/TC 144 - Tractors and machinery for agriculture and forestry
• Drafting Committee: CEN/TC 144 - Tractors and machinery for agriculture and forestry
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 05-Nov-2008
• Completion Date: 05-Nov-2008
• Directive: 98/37/EC - Machinery
• Mandate: M/079 - Mandate to CEN and CENELEC for standardization in the field of machines
• Ref Project: SIST EN ISO 11681-2:2007 - Machinery for forestry - Portable chain-saw safety requirements and testing - Part 2: Chain-saws for tree service (ISO 11681-2:2006)

Relations

• Replaces: EN ISO 11681-2:1998 - Machinery for forestry - Portable chain-saws - Safety requirements and testing - Part 2: Chain-saws for tree service (ISO 11681-2:1998)
• Effective Date: 22-Dec-2008
• Replaces: EN ISO 11681-2:1998/A1:2003 - Machinery for forestry - Portable chain-saws - Safety requirements and testing - Part 2: Chain-saws for tree service - Amendment 1 (ISO 11681-2:1998/AM 1:2003)
• Effective Date: 22-Dec-2008
• Replaced By: EN ISO 11681-2:2008 - Machinery for forestry - Portable chain-saw safety requirements and testing - Part 2: Chain-saws for tree service (ISO 11681-2:2006)
• Effective Date: 22-Dec-2008

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 11681-2:2007
01-januar-2007
1DGRPHãþD
SIST EN ISO 11681-2:1999
SIST EN ISO 11681-2:1999/A1:2004
Gozdarski stroji - Zahteve za prenosne motorne verižne žage in preskušanje - 2.
del: Žage za nego dreves (ISO/DIS 11681-2:2004)
Machinery for forestry - Portable chain-saw safety requirements and testing - Part 2:
Chain-saws for tree service (ISO 11681-2:2006)
Forstmaschinen - Sicherheitstechnische Anforderungen und Prüfungen für tragbare
Kettensägen - Teil 2: Kettensägen für die Baumpflege (ISO 11681-2:2006)
Matériel forestier - Exigences de sécurité et essais des scies a chaîne portatives - Partie
2: Scies a chaîne pour l'élagage des arbres (ISO 11681-2:2006)
Ta slovenski standard je istoveten z: EN ISO 11681-2:2006
ICS:
65.060.80
SIST EN ISO 11681-2:2007 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

EUROPEAN STANDARD
EN ISO 11681-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2006
ICS 65.060.80 Supersedes EN ISO 11681-2:1998
English Version
Machinery for forestry - Portable chain-saw safety requirements
and testing - Part 2: Chain-saws for tree service (ISO 11681-
2:2006)
Matériel forestier - Exigences de sécurité et essais des Forstmaschinen - Sicherheitstechnische Anforderungen
scies à chaîne portatives - Partie 2: Scies à chaîne pour und Prüfungen für tragbare Kettensägen - Teil 2:
l'élagage des arbres (ISO 11681-2:2006) Kettensägen für die Baumpflege (ISO 11681-2:2006)
This European Standard was approved by CEN on 12 June 2006.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2006 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11681-2:2006: E
worldwide for CEN national Members.

---------------------- Page: 2 ----------------------

EN ISO 11681-2:2006 (E)





Foreword


This document (EN ISO 11681-2:2006) has been prepared by Technical Committee ISO/TC 23
"Tractors and machinery for agriculture and forestry" in collaboration with Technical Committee
CEN/TC 144 "Tractors and machinery for agriculture and forestry", the secretariat of which is held
by AFNOR.

This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by January 2007, and conflicting national standards
shall be withdrawn at the latest by January 2007.

This document supersedes EN ISO 11681-2:1998.

This document has been prepared under a mandate given to CEN by the European Commission
and the European Free Trade Association, and supports essential requirements of EU Directive(s).

For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this
document.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Cyprus,
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.


Endorsement notice

The text of ISO 11681-2:2006 has been approved by CEN as EN ISO 11681-2:2006 without any
modifications.

2

---------------------- Page: 3 ----------------------

EN ISO 11681-2:2006 (E)



ANNEX ZA
(informative)

Relationship between this European Standard and the Essential
Requirements of EU Directive 98/37/EC, amended by Directive 98/79/EC



This European Standard has been prepared under a mandate given to CEN by the European
Commission and the European Free Trade Association to provide a means of conforming to
Essential Requirements of the New Approach Directive 98/37/EC, amended
...