EN 1360:2005

Rubber and plastic hoses and hose assemblies for measured fuel dispensing systems - Specification

This European Standard specifies minimum requirements for three types of hoses in two categories and two classes of hose assemblies used for measured fuel dispensing, including oxygenated fuels (up to a maximum of 15 % oxygenated compounds).
The assemblies are intended for use at ambient temperatures between -30 °C and +55 °C for normal temperature class and -40 °C and +55 °C for low temperature class at a working pressure £ 16 bar ) .

Zapfstellenschläuche und -schlauchleitungen aus Gummi und Kunststoff - Anforderungen

Diese Europäische Norm legt für drei Typen von Zapfstellenschläuchen für Kraftstoffe, die in zwei Kategorien
und zwei Klassen  unterteilt  werden, die Mindestanforderungen fest, wobei mit sauerstoffhaltigen
Verbindungen  angereicherte  Kraftstoffe (bis  zu einem maximalen Anteil  von 15 %  sauerstoffhaltigen
Verbindungen) einbezogen sind.
Die Anwendung  von Schlauchleitungen der  Normaltemperaturklasse  ist bei Umgebungstemperaturen
zwischen  . 30 °C  bis  + 55 °C  und  von  Schlauchleitungen der Tieftemperaturklasse zwischen  . 40 °C  und
+ 55 °C bei einem Arbeitsdruck von 16 bar1) vorgesehen.

Tuyaux et flexibles en caoutchouc pour distribution mesurée de carburants - Spécification

La présente Norme européenne spécifie les exigences minimales pour trois types de tuyaux dans deux
catégories et deux classes de flexibles utilisés pour la distribution mesurée des carburants, y compris les
carburants oxygénés (comprenant jusqu�à 15 % maximum de composants oxygénés).
Les flexibles sont destinés à être utilisés à température ambiante comprise entre - 30 °C et + 55 °C pour une
classe de température normale et - 40 °C à + 55 °C pour la classe basse température à une pression de
travail £ 16 bar1).

Gumene in polimerne cevi in cevni priključki za merjeno točenje goriv - Specifikacija

General Information

• Status: Withdrawn
• Publication Date: 03-May-2005
• Withdrawal Date: 18-Jun-2013
• ICS: 23.040.70 - Hoses and hose assemblies
• ICS: 75.200 - Petroleum products and natural gas handling equipment
• Technical Committee: CEN/TC 218 - Rubber and plastics hoses and hose assemblies
• Drafting Committee: CEN/TC 218/WG 1 - Rubber and plastics hoses and hose assemblies for industrial, chemical and petrochemical applications
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 19-Jun-2013
• Completion Date: 19-Jun-2013
• Ref Project: SIST EN 1360:2005 - Rubber and plastic hoses and hose assemblies for measured fuel dispensing systems - Specification

Relations

• Replaces: EN 1360:1996 - Rubber hoses and hose assemblies for measured fuel dispensing - Specification
• Effective Date: 22-Dec-2008
• Replaced By: EN 1360:2013 - Rubber and plastic hoses and hose assemblies for measured fuel dispensing systems - Specification
• Effective Date: 03-Jul-2010

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.6SHFLILNDFLMDZapfstellenschläuche und -schlauchleitungen aus Gummi und Kunststoff - AnforderungenTuyaux et flexibles en caoutchouc pour distribution mesurée de carburants - SpécificationRubber and plastic hoses and hose assemblies for measured fuel dispensing systems - Specification83.140.40Gumene ceviHoses75.200Petroleum products and natural gas handling equipmentICS:Ta slovenski standard je istoveten z:EN 1360:2005SIST EN 1360:2005en01-julij-2005SIST EN 1360:2005SLOVENSKI
STANDARDSIST EN 1360:20001DGRPHãþD

EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 1360
May 2005 ICS 75.200; 23.040.70
Supersedes EN 1360:1996
English version
Rubber and plastic hoses and hose assemblies for measured fuel dispensing systems - Specification
Tuyaux et flexibles en caoutchouc pour distribution mesurée de carburants - Spécification
Zapfstellenschläuche und -schlauchleitungen aus Gummi und Kunststoff - Anforderungen This European Standard was approved by CEN on 15 March 2005.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36
B-1050 Brussels © 2005 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1360:2005: ESIST EN 1360:2005

Test method for determination of low temperature resistance at –30 °C (for normal temperature class) and –40 °C (for low temperature class).13 A.1 Test piece.13 A.2 Apparatus.13 A.3 Test method.13 Annex B (normative)
Method for the determination of adhesion between components.15 B.1 Dry adhesion.15 B.2 Adhesion after contact with fuel.15 Annex C (normative)
Test method for the determination of low temperature flexibility.16 C.1 Test piece.16 C.2 Apparatus.16 C.3 Test method.16 Annex D (normative)
Test method for the determination of fuel permeation.18 D.1 Test piece.18 D.2 Apparatus.18 SIST EN 1360:2005

Test method for flammability.19 E.1 Test pieces.19 E.2 Apparatus.19 E.3 Test method.19 Annex F (normative)
End-fitting pull-off test.21 F.1 Test piece.21 F.2 Apparatus.21 F.3 Test method.21 Annex G (normative)
Test method for the determination of leakage (leak test).22 Annex H (normative)
Test method for fatigue strength under reversed bending stress (flex test).23 H.1 Apparatus and test pieces.23 H.2 Test method.24 H.3 Test observations and report.24 Annex I (normative)
Test frequency for type tests and routine tests.25 Annex J (informative)
Test frequency for production acceptance tests.27
1 Scope This European Standard specifies minimum requirements for three types of hoses in two categories and two classes of hose assemblies used for measured fuel dispensing, including oxygenated fuels (up to a maximum of 15 % oxygenated compounds). The assemblies are intended for use at ambient temperatures between –30 °C and +55 °C for normal temperature class and –40 °C and +55 °C for low temperature class at a working pressure ≤ 16 bar1). 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 26801, Rubber or plastics hoses — Determination of volumetric expansion (ISO 6801:1983). EN 27326, Rubber and plastics hoses — Assessment of ozone resistance under static conditions (ISO 7326:1991). EN 28033, Rubber and plastics hose — Determination of adhesion between components (ISO 8033:1991). EN ISO 1307, Rubber and plastics hoses for general-purpose industrial applications — Bore diameters and tolerances, and tolerances on length (ISO 1307:1992). EN ISO 1402, Rubber and plastics hoses and hose assemblies — Hydrostatic testing (ISO 1402:1994). EN ISO 1746, Rubber or plastics hoses and tubing - Bending tests (ISO 1746:1998, including technical corrigendum 1:1999). EN ISO 4671, Rubber and plastics hose and hose assemblies — Methods of measurement of dimensions (ISO 4671:1999). EN ISO 8031, Rubber and plastics hoses and hose assemblies — Determination of electrical resistance (ISO 8031:1993). EN ISO 8330:2000, Rubber and plastics hoses and hose assemblies — Vocabulary (ISO 8330:1998). ISO 37, Rubber, vulcanised or thermoplastic — Determination of tensile stress-strain properties. ISO 188, Rubber, vulcanised or thermoplastic — Accelerated ageing and heat-resistance tests. ISO 554, Standard atmospheres for conditioning and/or testing — Specifications. ISO 1817, Rubber, vulcanised — Determination of the effect of liquids. ISO 4649, Rubber, vulcanised or thermoplastic — Determination of abrasion resistance using a rotating cylindrical drum device.
1) 1 bar = 0,1 MPa SIST EN 1360:2005

c) Type 3: fine wire reinforced. Hoses for this application shall be divided into two categories: d) Category M: electrically bonded e) Category Ω: electrically conductive Hoses for this application shall be divided into two temperature classes: Normal temperature class with an ambient working temperature of −30 °C to +55 °C Low temperature class (LT) with an ambient working temperature of −40 °C to +55 °C 5 Materials and construction The hose shall consist of the following: - a smooth, fuel resistant lining of rubber or thermoplastic elastomer (TPE); - a suitable reinforcement; related to type; - a non-corrugated, fuel and weather-resistant rubber or TPE cover. Hose assemblies shall be capable of conducting an electrical charge from coupling to couplin
...