iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 1761:1999

(Main)

Rubber hoses and hose assemblies for fuel truck delivery - Specification

Rubber hoses and hose assemblies for fuel truck delivery - Specification

This European Standard specifies the requirements for two types of rubber hoses and rubber hose assemblies for loading and discharge of liquid hydrocarbon fuels with a maximum working pressure of 10 bar. Both types of hose are designed for: a) use with hydrocarbon fuels, having an aromatic hydrocarbon content not exceeding 50 % by volume and containing oxygenated compounds up to 15 %; b) operation within the temperature range of -30°C to +70°C, undamaged by climatic conditions of -50°C to 70°C when stored in static conditions.

Gummischläuche und schlauchleitungen für Tankwagen - Spezifikation

Diese Europäische Norm legt die Anforderungen fest für zwei Typen von Gummischläuchen und Gummischlauchleitungen zum Beladen und Entladen von flüssigen Kohlenwasserstoff-Treibstoffen mit einem höchsten Arbeitsdruck von 10 bar. Beide Schlauchtypen sind bestimmt für: a) die Verwendung mit Kohlenwasserstoff-Treibstoffen, die einen Gehalt an aromatischen Kohlenwasserstoff haben, der 50 Volumen-% nicht überschreitet, und die bis zu 15% an sauerstoffhaltigen Bestandteilen enthalten;

Tuyaux et flexibles en caoutchouc pour la livraison d'hydrocarbures liquides par camions-citernes - Spécification

La présente norme européenne spécifie les prescriptions pour deux types de tuyaux et de flexibles en caoutchouc destinés au chargement et au déchargement des hydrocarbures liquides sous une pression maximale de service de 10 bar. Ces deux types de tuyaux sont conçus pour: a) être employés avec des carburants à base d'hydrocarbures ayant une teneur en hydrocarbures aromatiques ne dépassant pas 50% en volume et en mélanges oxygénés inférieure ou égale à 15%; b) être utilisés dans une plage de température se situant entre -30°C et +70°C, sans être endommagés par des conditions climatiques de -50°C à 70°C ...

Gumene cevi in cevni priključki za dostavo goriva s cisterno - Specifikacija

General Information

Status
Published
Publication Date
16-Feb-1999
Withdrawal Date
30-Aug-1999
ICS
23.040.70 - Hoses and hose assemblies
75.200 - Petroleum products and natural gas handling equipment
Technical Committee
CEN/TC 218 - Rubber and plastics hoses and hose assemblies
Drafting Committee
CEN/TC 218/WG 1 - Rubber and plastics hoses and hose assemblies for industrial, chemical and petrochemical applications
Current Stage
Ref Project
SIST EN 1761:2000 - Rubber hoses and hose assemblies for fuel truck delivery - Specification

Relations

Revised
prEN 1761 - Rubber hoses and hose assemblies for fuel truck delivery - Specification
Effective Date
08-Feb-2023

Buy Standard

EN 1761:2000EN 1761:2000
PreviousNext
Standard
EN 1761:2000
English language
16 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.HFLILNDFLMDGummischläuche und schlauchleitungen für Tankwagen - SpezifikationTuyaux et flexibles en caoutchouc pour la livraison d'hydrocarbures liquides par camions-citernes - SpécificationRubber hoses and hose assemblies for fuel truck delivery - Specification83.140.40Gumene ceviHoses75.200Petroleum products and natural gas handling equipmentICS:Ta sloven
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 13483:2022(Main)
Rubber and plastic hoses and hose assemblies with internal vapour recovery for measured fuel dispensing systems - Specification
SIST EN 13483:2022

This document specifies the requirements and test methods for verification for hose assemblies with vapour recovery for delivery systems on petrol filling stations.
Hoses can be constructed from rubber or thermoplastic elastomer (TPE) and this document specifies the requirements for three types of hoses in two grades and two classes of hose assemblies for measured fuel dispensing systems, including oxygenated fuels (≤15 % oxygenated compounds) with internal vapour recovery tubing or hose made out of rubber or thermoplastic elastomer (TPE).
The assemblies are intended for use at ambient temperatures between -30 °C and +55 °C for normal temperature class and -40 °C and +55 °C for low temperature class at a working pressure ≤ 16 bar.
This document is not applicable to multi chamber fuel dispensing hoses.
NOTE As part of the certification of a new dispenser, testing of fuel samples in accordance with EN 228 is carried out at least eight weeks after the first use of the equipment to avoid unrepresentative sulphur content results.
1 bar = 0,1 MPa.

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1765:2016(Main)
Rubber hose assemblies for oil suction and discharge services - Specification for the assemblies
SIST EN 1765:2016

This European Standard specifies the characteristics of four types of oil suction and discharge hose assemblies used for the conveyance of petroleum, including crude oils and other liquid petroleum products containing a maximum aromatics content of 50 % (v/v). It is not suitable for liquefied petroleum gas and natural gas.
Hose assemblies to this document can be used in the temperature range −20 °C to 82 °C.
The hoses specified are in the size range of nominal bore 50 to 500 and may be smooth bore, rough bore or armoured rough bore.
Hoses for use with petroleum products having an aromatic content greater than 50 % (v/v) are outside the scope of this document but the requirements may be used as a basis for such hoses on request to the manufacturer.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 6808:2014(Main)
Plastics hoses and hose assemblies for suction and low-pressure discharge of petroleum liquids - Specification (ISO 6808:2014)
SIST EN ISO 6808:2014

ISO 6808:2014 specifies the requirements for two types of polymer-reinforced thermoplastics hose and hose assembly for suction and discharge applications with kerosene, heating oil, diesel fuel, and lubricating oils in the temperature range -10 °C to +45 °C.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1360:2013(Main)
Rubber and plastic hoses and hose assemblies for measured fuel dispensing systems - Specification
SIST EN 1360:2013

This European Standard specifies minimum requirements and test methods for verification for three types of hoses in two grades and two classes of hose assemblies used for measured fuel dispensing, including oxygenated fuels (up to a maximum of 15 % oxygenated compounds).
The assemblies are intended for use at ambient temperatures between –30 °C and +55 °C for normal temperature class and –40 °C and +55 °C for low temperature class at a working pressure  16 bar ).
As part of the certification of a new dispenser, testing of fuel samples in accordance with EN 228 and EN 590 should be carried out at least eight weeks after the first use of the equipment to avoid unrepresentative sulphur content results.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
prEN 1761(Main)
Rubber hoses and hose assemblies for fuel truck delivery - Specification
oSIST prEN 1761:2024

This document specifies the requirements for two types of rubber hoses and rubber hose assemblies for loading and discharge of liquid hydrocarbon fuels with a maximum working pressure of 10 bar (1,0 MPa).
Both types of hose are designed for:
a)   use with hydrocarbon fuels, having an aromatic hydrocarbon content not exceeding 50 % by volume and containing oxygenated compounds up to 15 %;
b)   operation within the temperature range of −30 °C to +70 °C, undamaged by climatic conditions of −50 °C to 70 °C when stored in static conditions.
This document is not applicable to hoses and hose assemblies for LPG, aviation fuel systems, fuel station systems and marine applications.

  • Draft
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13483:2022(Main)
Rubber and plastic hoses and hose assemblies with internal vapour recovery for measured fuel dispensing systems - Specification
SIST EN 13483:2022

This document specifies the requirements and test methods for verification for hose assemblies with vapour recovery for delivery systems on petrol filling stations.
Hoses can be constructed from rubber or thermoplastic elastomer (TPE) and this document specifies the requirements for three types of hoses in two grades and two classes of hose assemblies for measured fuel dispensing systems, including oxygenated fuels (≤15 % oxygenated compounds) with internal vapour recovery tubing or hose made out of rubber or thermoplastic elastomer (TPE).
The assemblies are intended for use at ambient temperatures between -30 °C and +55 °C for normal temperature class and -40 °C and +55 °C for low temperature class at a working pressure ≤ 16 bar.
This document is not applicable to multi chamber fuel dispensing hoses.
NOTE As part of the certification of a new dispenser, testing of fuel samples in accordance with EN 228 is carried out at least eight weeks after the first use of the equipment to avoid unrepresentative sulphur content results.
1 bar = 0,1 MPa.

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1765:2016(Main)
Rubber hose assemblies for oil suction and discharge services - Specification for the assemblies
SIST EN 1765:2016

This European Standard specifies the characteristics of four types of oil suction and discharge hose assemblies used for the conveyance of petroleum, including crude oils and other liquid petroleum products containing a maximum aromatics content of 50 % (v/v). It is not suitable for liquefied petroleum gas and natural gas.
Hose assemblies to this document can be used in the temperature range −20 °C to 82 °C.
The hoses specified are in the size range of nominal bore 50 to 500 and may be smooth bore, rough bore or armoured rough bore.
Hoses for use with petroleum products having an aromatic content greater than 50 % (v/v) are outside the scope of this document but the requirements may be used as a basis for such hoses on request to the manufacturer.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 6808:2014(Main)
Plastics hoses and hose assemblies for suction and low-pressure discharge of petroleum liquids - Specification (ISO 6808:2014)
SIST EN ISO 6808:2014

ISO 6808:2014 specifies the requirements for two types of polymer-reinforced thermoplastics hose and hose assembly for suction and discharge applications with kerosene, heating oil, diesel fuel, and lubricating oils in the temperature range -10 °C to +45 °C.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1360:2013(Main)
Rubber and plastic hoses and hose assemblies for measured fuel dispensing systems - Specification
SIST EN 1360:2013

This European Standard specifies minimum requirements and test methods for verification for three types of hoses in two grades and two classes of hose assemblies used for measured fuel dispensing, including oxygenated fuels (up to a maximum of 15 % oxygenated compounds).
The assemblies are intended for use at ambient temperatures between –30 °C and +55 °C for normal temperature class and –40 °C and +55 °C for low temperature class at a working pressure  16 bar ).
As part of the certification of a new dispenser, testing of fuel samples in accordance with EN 228 and EN 590 should be carried out at least eight weeks after the first use of the equipment to avoid unrepresentative sulphur content results.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
prEN 1761(Main)
Rubber hoses and hose assemblies for fuel truck delivery - Specification
oSIST prEN 1761:2024

This document specifies the requirements for two types of rubber hoses and rubber hose assemblies for loading and discharge of liquid hydrocarbon fuels with a maximum working pressure of 10 bar (1,0 MPa).
Both types of hose are designed for:
a)   use with hydrocarbon fuels, having an aromatic hydrocarbon content not exceeding 50 % by volume and containing oxygenated compounds up to 15 %;
b)   operation within the temperature range of −30 °C to +70 °C, undamaged by climatic conditions of −50 °C to 70 °C when stored in static conditions.
This document is not applicable to hoses and hose assemblies for LPG, aviation fuel systems, fuel station systems and marine applications.

  • Draft
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day