Industrial valves - Multi-turn valve actuator attachments (ISO 5210:2017)

ISO 5210:2017 specifies the requirements for the attachment of multi-turn actuators to valves.
Throughout this document, "actuator" may be understood as "actuator and/or gearbox" providing a multi-turn and/or linear output.
ISO 5210:2017  specifies:
-      flange dimensions necessary for the attachment of actuators to industrial valves [see Figure 1 a)] or to intermediate supports [see Figure 1 b)];
-      those driving component dimensions of actuators which are necessary to attach them to the driven components;
-      reference values for torque and thrust for flanges having the dimensions specified in this document.

Industriearmaturen - Anschlüsse von Drehantrieben für Armaturen (ISO 5210:2017)

Dieses Dokument legt die Anforderungen für den Anschluss von Drehantrieben an Armaturen fest.
In diesem Dokument darf "Stellantrieb" als "Stellantrieb und/oder Getriebe" betrachtet werden, sofern es sich um einen Dreh- und/oder Linearantrieb handelt.
Es legt Folgendes fest:
-   die Maße der Flansche, die für den Anschluss von Stellantrieben an Industriearmaturen [siehe Bild 1a)] oder an Zwischenstücke [siehe Bild 1b)] notwendig sind;
-   die Maße der antreibenden Teile von Stellantrieben, die notwendig sind, um diese mit den angetriebenen Teilen zu verbinden;
-   die Bezugswerte für Drehmoment und Schubkraft für Flansche mit den in diesem Dokument festgelegten Abmessungen.
ANMERKUNG 1   In diesem Dokument kann der Begriff "Armatur" auch als "Armatur mit einem Zwischenstück" [siehe Bild 1b)] verstanden werden.
ANMERKUNG 2   Wenn eine Kombination aus einem Drehantrieb und einem seperaten Dreh-/Lineargetriebe zu einem Stellantrieb gekoppelt wird, dann stimmt der Anschluss des Drehantriebs an das Getriebe mit diesem Dokument [siehe Bilder 1c) und 1d)] überein. Eine Kombination aus einem Drehantrieb mit einem integrierten Dreh-/Lineargetriebe, die als Stellantrieb bereitgestellt wird, stimmt  mit den Bildern 1a) und 1b) überein.

Robinetterie industrielle - Raccordement des actionneurs multitours aux appareils de robinetterie (ISO 5210:2017)

ISO 5210:2017 prescrit les exigences de raccordement des actionneurs multitours aux appareils de robinetterie.
Tout au long du présent document, le terme «actionneur» peut être compris comme «actionneur et/ou réducteur» fournissant une sortie multitours et/ou linéaire.
ISO 5210:2017 prescrit:
-      les dimensions des brides nécessaires pour le raccordement des actionneurs aux appareils de robinetterie industrielle [voir Figure 1 a)] ou aux supports intermédiaires [voir Figure 1 b)];
-      les dimensions des éléments d'entraînement des actionneurs nécessaires à leur accouplement aux éléments entraînés;
-      les valeurs de référence du couple et de la poussée pour les brides ayant les dimensions spécifiées dans le présent document.

Industrijski ventili - Priključki vrtilnih pogonov na ventilih (ISO 5210:2017)

Ta dokument določa zahteve za priključitev vrtilnih pogonov na ventile. Izraz »pogon« v tem dokumentu lahko pomeni »pogon in/ali menjalnik«, ki omogoča vrtilni in/ali linearni izhod.
Določa:
– dimenzije prirobnic, ki so potrebne za pritrditev pogona na industrijske ventile [glej sliko 1 a)] ali
vmesne podpornike [glej sliko 1 b)];
– dimenzije pogonskih komponent pogonov, ki so potrebne za pritrditev pogonov na pogonske
komponente;
– referenčne vrednosti za navor in potisk za prirobnice z merami, določenimi v tem dokumentu.
OPOMBA 1: Izraz »ventil« v tem dokumentu lahko pomeni »ventil z vmesnim podpornikom« [glej sliko 1 b)].
OPOMBA 2: Ko je kombinacija vrtilnega pogona in ločenega vrtilnega/linearnega menjalnika sklopljena, tako da tvori pogon, mora biti priključek vrtilnega pogona na menjalnik v skladu s tem dokumentom [glej sliki 1 c) in 1 d)]. Kombinacija vrtilnega pogona z integriranim vrtilnim/linearnim menjalnikom, ki je dobavljena kot pogon, je v skladu s slikama 1 a) in 1 b).

General Information

Status
Published
Publication Date
25-Apr-2017
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Due Date
26-Apr-2017
Completion Date
26-Apr-2017

RELATIONS

Buy Standard

Standard
EN ISO 5210:2017
English language
23 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (sample)

SLOVENSKI STANDARD
SIST EN ISO 5210:2017
01-julij-2017
1DGRPHãþD
SIST EN ISO 5210:2000
,QGXVWULMVNLYHQWLOL3ULNOMXþNLYUWLOQLKSRJRQRYQDYHQWLOLK ,62
Industrial valves - Multi-turn valve actuator attachments (ISO 5210:2017)
Industriearmaturen - Anschlüsse von Drehantrieben für Armaturen (ISO 5210:2017)

Robinetterie industrielle - Raccordement des actionneurs multitours aux appareils de

robinetterie (ISO 5210:2017)
Ta slovenski standard je istoveten z: EN ISO 5210:2017
ICS:
23.060.01 Ventili na splošno Valves in general
SIST EN ISO 5210:2017 en

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 5210:2017
---------------------- Page: 2 ----------------------
SIST EN ISO 5210:2017
EN ISO 5210
EUROPEAN STANDARD
NORME EUROPÉENNE
April 2017
EUROPÄISCHE NORM
ICS 23.060.01 Supersedes EN ISO 5210:1996
English Version
Industrial valves - Multi-turn valve actuator attachments
(ISO 5210:2017)

Robinetterie industrielle - Raccordement des Industriearmaturen - Anschlüsse von Drehantrieben

actionneurs multitours aux appareils de robinetterie für Armaturen (ISO 5210:2017)

(ISO 5210:2017)
This European Standard was approved by CEN on 1 March 2017.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this

European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references

concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN

member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by

translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management

Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,

Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,

Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,

Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels

© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 5210:2017 E

worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 5210:2017
EN ISO 5210:2017 (E)
Contents Page

European foreword ....................................................................................................................................................... 3

---------------------- Page: 4 ----------------------
SIST EN ISO 5210:2017
EN ISO 5210:2017 (E)
European foreword

This document (EN ISO 5210:2017) has been prepared by Technical Committee ISO/TC 153 “Valves” in

collaboration with Technical Committee CEN/TC 69 “Industrial valves” the secretariat of which is held

by AFNOR.

This European Standard shall be given the status of a national standard, either by publication of an

identical text or by endorsement, at the latest by October 2017, and conflicting national standards shall

be withdrawn at the latest by October 2017.

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent

rights.
This document supersedes EN ISO 5210:1996.

According to the CEN-CENELEC Internal Regulations, the national standards organizations of the

following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,

Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,

France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,

Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,

Turkey and the United Kingdom.
Endorsement notice

The text of ISO 5210:2017 has been approved by CEN as EN ISO 5210:2017 without any modification.

---------------------- Page: 5 ----------------------
SIST EN ISO 5210:2017
---------------------- Page: 6 ----------------------
SIST EN ISO 5210:2017
INTERNATIONAL ISO
STANDARD 5210
Second edition
2017-03
Industrial valves — Multi-turn valve
actuator attachments
Robinetterie industrielle — Raccordement des actionneurs multitours
aux appareils de robinetterie
Reference number
ISO 5210:2017(E)
ISO 2017
---------------------- Page: 7 ----------------------
SIST EN ISO 5210:2017
ISO 5210:2017(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2017, Published in Switzerland

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form

or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior

written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of

the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 5210:2017
ISO 5210:2017(E)
Contents Page

Foreword ........................................................................................................................................................................................................................................iv

Introduction ..................................................................................................................................................................................................................................v

1 Scope ................................................................................................................................................................................................................................. 1

2 Normative references ...................................................................................................................................................................................... 2

3 Terms and definitions ..................................................................................................................................................................................... 2

4 Maximum torques and thrusts ............................................................................................................................................................... 3

5 Flange dimensions .............................................................................................................................................................................................. 4

6 Designation ................................................................................................................................................................................................................ 6

7 Dimensions of driving and driven components ................................................................................................................... 6

7.1 General ........................................................................................................................................................................................................... 6

7.2 Dimensions for assemblies capable of transmitting both torque and thrust: Group A ............ 6

7.3 Dimensions for assemblies capable of transmitting torque only: Group B ........................................ 8

7.4 Dimensions for assemblies capable of transmitting torque only: Group C ......................................... 9

7.5 Dimensions for assemblies capable of transmitting torque only: Group D .....................................10

7.6 Dimensions for assemblies capable of transmitting thrust only: Group Linear actuators .11

Annex A (informative) Explanation of calculations ...........................................................................................................................13

Bibliography .............................................................................................................................................................................................................................15

© ISO 2017 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 5210:2017
ISO 5210:2017(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of

any patent rights identified during the development of the document will be in the Introduction and/or

on the ISO list of patent declarations received (see www .iso .org/ patents).

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and

expressions related to conformity assessment, as well as information about ISO’s adherence to the

World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following

URL: w w w . i s o .org/ iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 153, Valves.

This second edition cancels and replaces the first edition (ISO 5210:1991), which has been technically

revised with the following changes:
a) extension of flange sizes;

b) introduction of groups C and D for assemblies capable of transmitting torque, in 7.4 and 7.5;

c) introduction of linear actuator in 7.6.
iv © ISO 2017 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 5210:2017
ISO 5210:2017(E)
Introduction

The purpose of this document is to establish certain basic requirements for the attachment of multi-

turn actuators, in order to define the interface between actuator and valve.

This document has, in general, to be considered in conjunction with the specific requirements which

may be agreed between the parties concerned.
© ISO 2017 – All rights reserved v
---------------------- Page: 11 ----------------------
SIST EN ISO 5210:2017
---------------------- Page: 12 ----------------------
SIST EN ISO 5210:2017
INTERNATIONAL STANDARD ISO 5210:2017(E)
Industrial valves — Multi-turn valve actuator attachments
1 Scope

This document specifies the requirements for the attachment of multi-turn actuators to valves.

Throughout this document, “actuator” may be understood as “actuator and/or gearbox” providing a

multi-turn and/or linear output.
It specifies:

— flange dimensions necessary for the attachment of actuators to industrial valves [see Figure 1 a)] or

to intermediate supports [see Figure 1 b)];

— those driving component dimensions of actuators which are necessary to attach them to the driven

components;

— reference values for torque and thrust for flanges having the dimensions specified in this document.

NOTE 1 In this document, the term “valve” may also be understood to include “valve with an intermediate

support” [see Figure 1 b)].

NOTE 2 When a combination of a multi-turn actuator and separate multi-turn/linear gearbox is coupled to

form an actuator, the multi-turn attachment to the gearbox is in accordance with this document [see Figures 1 c)

and 1 d)]. A combination of a multi-turn actuator with integral multi-turn/linear gearbox supplied as an actuator

is in accordance with Figures 1 a) and 1 b).
© ISO 2017 – All rights reserved 1
---------------------- Page: 13 ----------------------
SIST EN ISO 5210:2017
ISO 5210:2017(E)

a) Direct interface b) Intermediate c) Direct interface d) Intermediate support

support interface (when combination interface (when
of a multi-turn combination of a multi-
actuator and multi- turn actuator and a
turn/linear multi-turn/linear
gearbox) gearbox)
Key
1 multi-turn/linear actuator 5 gearbox
2 interface (see ISO 5210) 6 interface (see ISO 5210)
3 valve 7 multi-turn actuator
4 intermediate support
Figure 1 — Interface between multi-turn/linear actuator and valve
2 Normative references

The following documents are referred to in the text in such a way that some or all of their content

constitutes requirements of this document. For dated references, only the edition cited applies. For

undated references, the latest edition of the referenced document (including any amendments) applies.

ISO 273, Fasteners — Clearance holes for bolts and screws
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.

ISO and IEC maintain terminological databases for use in standardization at the following addresses:

— IEC Electropedia: available at http:// www .electropedia .org/
— ISO Online browsing platform: available at http:// www .iso .org/ obp
2 © ISO 2017 – All rights reserved
---------------------- Page: 14 ----------------------
SIST EN ISO 5210:2017
ISO 5210:2017(E)
3.1
actuator

any device designed for attachment to a general purpose industrial valve in order to provide for the

operation of the valve

Note 1 to entry: The device is designed to operate using motive energy which may be electrical, pneumatic,

hydraulic, manual, etc., or a combination of these. Movement is limited by travel, torque and/or thrust.

3.2
multi-turn actuator

actuator which transmits torque to the valve for at least one revolution and may be capable of

withstanding thrust

Note 1 to entry: An actuator may be a combination of a multi-turn actuator and multi-turn

...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.