EN ISO 11363-2:2010
(Main)Gas cylinders - 17E and 25E taper threads for connection of valves to gas cylinders - Part 2: Inspection gauges (ISO 11363-2:2010)
Gas cylinders - 17E and 25E taper threads for connection of valves to gas cylinders - Part 2: Inspection gauges (ISO 11363-2:2010)
ISO 11363-2:2010 specifies types, dimensions and principles of use of gauges, to be used in conjunction with the taper threads specified in ISO 11363-1 (i.e. 17E and 25E threads).
It provides examples of calculations for thread gauge dimensions on the large end diameter and draws attention to the limitations of the gauging system specified.
Gasflaschen - 17E und 25E kegeliges Gewinde zur Verbindung von Ventilen mit Gasflaschen - Teil 2: Prüflehren (ISO 11363-2:2010)
Dieser Teil der ISO 11363 legt Typen, Maße und Anwendungsgrundsätze von Lehren, die in Verbindung mit
den kegeligen Gewinden nach ISO 11363-1 (d. h. 17E- und 25E-Gewinde) angewendet werden, fest.
Er enthält Berechnungsbeispiele für die Abmaße von Gewindelehren für den großen Kegeldurchmesser
(Anhang A) und informiert über die Grenzen des in der vorliegenden Norm festgelegten Lehren-Systems
(Anhang B).
Bouteilles à gaz - Filetages coniques 17E et 25E pour le raccordement des robinets sur les bouteilles à gaz - Partie 2: Calibres de contrôle (ISO 11363-2:2010)
L'ISO 11363-2:2010 spécifie les types, les dimensions et les principes d'utilisation des calibres, à utiliser conjointement avec les cônes filetés spécifiés dans l'ISO 11363-1 (c'est-à-dire à filetages 17E et 25E).
Elle donne des exemples de calculs des dimensions de calibres filetés fondés sur le diamètre de la grosse extrémité et elle attire l'attention sur les limites du système de vérification par calibres spécifié.
Plinske jeklenke - Konična navoja 17E in 25E za priključitev ventila na plinsko jeklenko - 2. del: Kalibri za kontrolo (ISO 11363-2:2010)
Ta del ISO 11363 določa vrste, mere in načela uporabe kalibrov, ki se uporabljajo v povezavi s koničnimi navoji, določenimi v ISO 11363-1 (tj. navojema 17E in 25E). Podaja primere izračunov za mere kalibrov navojev na koncu z večjim premerom (Dodatek A) in opozarja na omejitve določenega kalibrskega sistema (Dodatek B).
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-oktober-2010
1DGRPHãþD
SIST EN 629-2:1999
SIST EN ISO 11116-2:2000
3OLQVNHMHNOHQNH.RQLþQDQDYRMD(LQ(]DSULNOMXþLWHYYHQWLODQDSOLQVNR
MHNOHQNRGHO .DOLEUL]DNRQWUROR ,62
Gas cylinders - 17E and 25E taper threads for connection of valves to gas cylinders -
Part 2: Inspection gauges (ISO 11363-2:2010)
Gasflaschen - 17E und 25E kegeliges Gewinde zur Verbindung von Ventilen mit
Gasflaschen - Teil 2: Lehrenprüfung (ISO 11363-2:2010)
Bouteilles à gaz - Filetages coniques 17E et 25E pour le raccordement des robinets sur
les bouteilles à gaz - Partie 2: Calibres de contrôle (ISO 11363-2:2010)
Ta slovenski standard je istoveten z: EN ISO 11363-2:2010
ICS:
21.040.30 Posebni navoji Special screw threads
23.020.30 7ODþQHSRVRGHSOLQVNH Pressure vessels, gas
MHNOHQNH cylinders
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 11363-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2010
ICS 23.020.30 Supersedes EN 629-2:1996, EN ISO 11116-2:1999
English Version
Gas cylinders - 17E and 25E taper threads for connection of
valves to gas cylinders - Part 2: Inspection gauges (ISO 11363-
2:2010)
Bouteilles à gaz - Filetages coniques 17E et 25E pour le Gasflaschen - 17E und 25E kegeliges Gewinde zur
raccordement des robinets sur les bouteilles à gaz - Partie Verbindung von Ventilen mit Gasflaschen - Teil 2:
2: Calibres de contrôle (ISO 11363-2:2010) Lehreninspektion (ISO 11363-2:2010)
This European Standard was approved by CEN on 23 January 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11363-2:2010: E
worldwide for CEN national Members.
Contents Page
Foreword .3
Foreword
This document (EN ISO 11363-2:2010) has been prepared by Technical Committee ISO/TC 58 "Gas
cylinders" in collaboration with Technical Committee CEN/TC 23 “Transportable gas cylinders” the secretariat
of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by November 2010, and conflicting national standards shall be withdrawn
at the latest by November 2010.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 629-2:1996, EN ISO 11116-2:1999.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 11363-2:2010 has been approved by CEN as a EN ISO 11363-2:2010 without any
modification.
INTERNATIONAL ISO
STANDARD 11363-2
First edition
2010-05-15
Gas cylinders — 17E and 25E taper
threads for connection of valves to gas
cylinders —
Part 2:
Inspection gauges
Bouteilles à gaz — Filetages coniques 17E et 25E pour le raccordement
des robinets sur les bouteilles à gaz —
Partie 2: Calibres de contrôle
Reference number
ISO 11363-2:2010(E)
©
ISO 2010
ISO 11363-2:2010(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2010
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2010 – All rights reserved
ISO 11363-2:2010(E)
Contents Page
Foreword .iv
Introduction.v
1 Scope.1
2 Normative references.1
3 Terms and definitions .1
4 Requirements.2
4.1 Materials .2
4.2 Thread profile.2
4.3 Thread handedness.4
4.4 Taper.4
4.5 Pitch, P.4
5 Gauge dimensions .4
6 Inspection gauges .5
6.1 Gauges for cylinder neck thread .5
6.2 Gauges for valve stem thread .7
7 Check gauges .9
8 Use of inspection gauges.9
8.1 Plain gauges .9
8.2 Threaded plug gauges .9
8.3 Accept or reject criteria using plug gauges .9
8.4 Accept or reject criteria using ring gauges .10
9 Verification of inspection gauges.11
9.1 General .11
9.2 Plug gauges .12
9.3 Ring gauges .12
9.4 Use of check plug gauges .12
10 Identification .12
10.1 Inspection gauges .12
10.2 Check gauges .13
Annex A (informative) Examples of calculation for thread gauge dimensions on the large end
diameter.14
Annex B (informative) Limitation of gauging system.16
Bibliography.18
ISO 11363-2:2010(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 11363-2 was prepared by Technical Committee ISO/TC 58, Gas cylinders, Subcommittee SC 2, Cylinder
fittings.
This first edition of ISO 11363-2 cancels and replaces ISO 11116-2:1999 and ISO 11191:1997.
ISO 11363 consists of the following parts, under the general title Gas cylinders — 17E and 25E taper threads
for connection of valves to gas cylinders:
⎯ Part 1: Specifications
⎯ Part 2: Inspection gauges
iv © ISO 2010 – All rights reserved
ISO 11363-2:2010(E)
Introduction
Gas cylinders intended to contain compressed, liquefied or dissolved gas under pressure are fitted with
accessories to allow release and refilling of gas. Hereinafter, the term “valve” will apply to such accessories.
The connection between cylinder and valve is obtained by assembly of two taper-threads (an external one on
the valve stem and an internal one in the cylinder neck), both having the same nominal taper, thread pitch and
thread profile.
INTERNATIONAL STANDARD ISO 11363-2:2010(E)
Gas cylinders — 17E and 25E taper threads for connection o
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.