iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 16728:2016/prA1

(Amendment)

LPG equipment and accessories - Transportable refillable LPG cylinders other than traditional welded and brazed steel cylinders - Periodic inspection

LPG equipment and accessories - Transportable refillable LPG cylinders other than traditional welded and brazed steel cylinders - Periodic inspection

This European Standard specifies procedures for periodic inspection and testing, for transportable refillable LPG cylinders with a water capacity from 0,5 l up to and including 150 l.
This European Standard is applicable to the following:
-   welded steel LPG cylinders manufactured to an alternative design and construction, see EN 14140 or equivalent standard;
-   welded aluminium LPG cylinders, see EN 13110 or equivalent standard;
-   composite LPG cylinders, see EN 14427 or equivalent standard;
-   over-moulded cylinders designed and manufactured according to EN 1442 or EN 14140, see Annex F.
NOTE   The requirements of RID/ADR take precedence over those of this Standard in the case of cylinders complying with that regulation, including pi marked cylinders.
This European Standard does not apply to cylinders permanently installed in vehicles.

Flüssiggas-Geräte und Ausrüstungsteile - Ortsbewegliche, wiederbefüllbare Flaschen für Flüssiggas (LPG), ausgenommen geschweißte und hartgelötete Stahlflaschen - Wiederkehrende Inspektion

Équipements pour GPL et leurs accessoires - Bouteilles transportables et rechargeables pour GPL autres que celles en acier soudé et brasé - Contrôle périodique

Oprema in pribor za utekočinjeni naftni plin (UNP) - Premične, ponovno polnljive plinske jeklenke za UNP, ki niso varjene ali trdo spajkane - Periodična kontrola - Dopolnilo A1

General Information

Status
Not Published
ICS
23.020.35 - Gas cylinders
Technical Committee
CEN/TC 286 - Liquefied petroleum gas equipment and accessories
Drafting Committee
CEN/TC 286/WG 7 - Operational requirements - Transportable LPG cylinders and static LPG tanks
Current Stage
4060 - Closure of enquiry - Enquiry
Start Date
07-Dec-2017
Due Date
05-Dec-2017
Completion Date
07-Dec-2017
Directive
2008/68/EC - Directve 2008/68/EC of the European Parliament and of the council of 24 September 2008 on the inland transport of the dangerous goods
Mandate
M/086 - Mandate to CEN for standardization in the field of transport of dangerous goods
Ref Project
SIST EN 16728:2016/oprA1:2017 - LPG equipment and accessories - Transportable refillable LPG cylinders other than traditional welded and brazed steel cylinders - Periodic inspection

Relations

Merged Into
EN 16728:2016+A1:2018 - LPG equipment and accessories - Transportable refillable LPG cylinders other than traditional welded and brazed steel cylinders - Periodic inspection
Effective Date
18-Jan-2023
Amends
EN 16728:2016 - LPG equipment and accessories - Transportable refillable LPG cylinders other than traditional welded and brazed steel cylinders - Periodic inspection
Effective Date
09-Nov-2016

Buy Standard

EN 16728:2016/oprA1:2017EN 16728:2016/oprA1:2017
PreviousNext
Draft
EN 16728:2016/oprA1:2017
English language
6 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 16728:2016/oprA1:2017
01-november-2017
2SUHPDLQSULERU]DXWHNRþLQMHQLQDIWQLSOLQ 813 3UHPLþQHSRQRYQRSROQOMLYH
SOLQVNHMHNOHQNH]D813NLQLVRYDUMHQHLQWUGRVSDMNDQH3HULRGLþQDNRQWUROD
'RSROQLOR$
LPG equipment and accessories - Transportable refillable LPG cylinders other than
traditional welded and brazed steel cylinders - Periodic inspection
Flüssiggas-Geräte und Ausrüstungsteile - Ortsbewegliche, wiederbefüllbare Flaschen für
Flüssiggas (LPG), ausgenommen geschweißte und hartgelötete Stahlflaschen -
Wiederkehrende Inspektion
Équipements pour GPL et leurs accessoires - Bouteilles transportables et rechargeables
pour GPL autres que celles en acier soudé et brasé - Contrôle périodique
Ta slovenski standard je istoveten z: EN 16728:2016/prA1
ICS:
23.020.35 Plinske jeklenke Gas cylinders
SIST EN 16728:2016/oprA1:2017 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 16728:2016/oprA1:2017

---------------------- Page: 2 ----------------------

SIST EN 16728:2016/oprA1:2017


DRAFT
EUROPEAN STANDARD
EN 16728:2016
NORME EUROPÉENNE

EUROPÄISCHE NORM
prA1
September 2017
ICS 23.020.35
English Version

LPG equipment and accessories - Transportable refillable
LPG cylinders other than traditional welded and brazed
steel cylinders - Periodic inspection
Équipements pour GPL et leurs accessoires - Bouteilles Flüssiggas-Geräte und Ausrüstungsteile -
transportables et rechargeables pour GPL autres que Ortsbewegliche, wiederbefüllbare Flaschen für
celles en acier soudé et brasé - Contrôle périodique Flüssiggas (LPG), ausgenommen geschweißte und
hartgelötete Stahlflaschen - Wiederkehrende
Inspektion
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 286.

This draft amendment A1, if approved, will modify the European Standard EN 16728:2016. If this draft becomes an amendment,
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration.

This draft amendment was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 16728:2016/prA1:2017 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 16728:2016/oprA1:2017
EN 16728:2016/prA1:2017 (E)
Contents Page
European foreword . 3
1 Modification to Clause 3. 4
2 Modification to 4.1 . 4
3 Modification to 5.3.1 . 4
4 Modification to 5.3.2.4 . 4
5 Modification to 5.3.3.2.1 . 4
6 Modification to 5.3.3.2.2 . 5
7 Modification to 6.2 .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 13110:2022(Main)
LPG equipment and accessories - Transportable refillable welded aluminium cylinders for liquefied petroleum gas (LPG) - Design and construction
SIST EN 13110:2023

This document specifies minimum requirements for material, design, construction and workmanship, testing and examination during the manufacture of transportable refillable welded aluminium liquefied petroleum gas (LPG) cylinders, having a water capacity from 0,5 l up to and including 150 l, exposed to ambient temperature.

  • Standard
    47 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14427:2022(Main)
LPG equipment and accessories - Transportable refillable composite cylinders for LPG - Design and construction
SIST EN 14427:2022

This document:
—   specifies minimum requirements for materials, design, construction, prototype testing and routine manufacturing inspections of fully wrapped composite cylinders with a water capacity from 0,5 litre up to and including 150 litres for liquefied petroleum gases (LPG) exposed to ambient temperatures, with a test pressure of at least 30 bar;
—   is only applicable to cylinders which are fitted with a pressure relief valve (see 4.1.3);
—   is applicable to cylinders with a liner of metallic material (welded or seamless) or non-metallic material (or a mixture thereof), reinforced by fibres of glass, carbon or aramid (or a mixture thereof);
—   is also applicable to composite cylinders without liners.
Cylinders manufactured to this document are suitable for temperatures down to −40 °C.
This document does not address the design, fitting and performance of removable protective sleeves. Where these are fitted, the choice of material and sleeve performance are expected to be considered separately.

  • Standard
    54 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14894:2021(Main)
LPG equipment and accessories - Cylinder and drum marking
SIST EN 14894:2022

This document specifies stamp marking requirements for transportable refillable LPG cylinders and metallic drums including:
- Steel LPG cylinders designed and manufactured in accordance with EN 1442, EN 14140, EN 12807 or an equivalent standard or technical code recognized by the Competent Authority.
- LPG metallic drums designed and manufactured in accordance with EN 14893 or an equivalent standard or technical code recognized by the Competent Authority.
- Welded aluminium LPG cylinders designed and manufactured in accordance with EN 13110 or an equivalent standard or technical code recognized by the Competent Authority.
- LPG composite cylinders designed and manufactured in accordance with EN 14427 or an equivalent standard or technical code recognized by the Competent Authority.
NOTE 1 All these types of receptacles are referred to throughout this document as “cylinders”.
This document does not specify any requirements for product, hazard or safety-phrase labelling of packaging which can be required to meet ADR or other legislative requirements.
NOTE 2 The marking of cylinders is regulated by RID/ADR which take precedence over any clause in this document. The European Directive on Transportable Pressure Equipment 2010/35/EU [8] includes additional marking requirements (π-marking). For countries that are not members of the European Union, the π marking is replaced by their relevant conformity mark.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1439:2021(Main)
LPG equipment and accessories - Procedure for checking transportable refillable LPG cylinders before, during and after filling
SIST EN 1439:2022

This document specifies the procedures to be adopted when checking transportable refillable LPG cylinders before, during and after filling.
This document is applicable to transportable refillable LPG cylinders of water capacity not exceeding 150 l and deemed to be fitted with valves designed according to EN ISO 14245 [4] and EN ISO 15995 [5].
This document does not apply to the requirements for filling LPG cylinders that are designed and equipped for filling by the user.
This document does not apply to the requirements for filling LPG containers on vehicles.
This document is applicable to the following:
—   welded and brazed steel LPG cylinders with a specified minimum wall thickness (see EN 1442 and EN 12807 [1] or an equivalent standard);
—   welded steel LPG cylinders without specified minimum wall thickness (see EN 14140 or an equivalent standard);
—   welded aluminium LPG cylinders (see EN 13110 [2] or an equivalent standard);
—   composite LPG cylinders (see EN 14427 or an equivalent standard); and
—   over-moulded cylinders (OMC).
Specific requirements for the different types of cylinders are detailed in Annex A, Annex B, Annex C, Annex D and Annex G.
This document is intended to be applicable to cylinders complying with RID/ADR [6] [7] (including pi marked cylinders) and also to existing non RID/ADR cylinder populations.

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 15995:2021(Main)
Gas cylinders - Specifications and testing of LPG cylinder valves - Manually operated (ISO 15995:2021)
SIST EN ISO 15995:2021

This document specifies the requirements for design, specification, type testing and production testing and inspection of dedicated LPG manually operated cylinder valves for use with and directly connected to transportable refillable LPG cylinders.
It also includes requirements for associated equipment for vapour and liquid service. Bursting discs and/or fusible plugs are not covered in this document.
Annex B identifies requirements for production testing and inspection.
This document excludes other LPG cylinder devices which are not an integral part of the dedicated manually operated cylinder valve.
This document does not apply to cylinder valves for fixed automotive installations and ball valves.
NOTE      For self-closing LPG cylinder valves see ISO 14245. For cylinder valves for compressed, dissolved and other liquefied gases see ISO 10297,[2] ISO 17871[6] or ISO 17879[7].

  • Standard
    34 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 14245:2021(Main)
Gas cylinders - Specifications and testing of LPG cylinder valves - Self-closing (ISO 14245:2021)
SIST EN ISO 14245:2021

This document specifies the requirements for design, specification, type testing and production testing and inspection for dedicated LPG self-closing cylinder valves for use with and directly connected to transportable refillable LPG cylinders.
It also includes requirements for associated equipment for vapour and liquid service. Bursting discs and/or fusible plugs are not covered in this document.
Annex A identifies requirements for production testing and inspection.
This document excludes other LPG cylinder devices which are not an integral part of the dedicated self-closing cylinder valve.
This document does not apply to cylinder valves for fixed automotive installations and ball valves.
NOTE         For manually operated LPG cylinder valves see ISO 15995. For cylinder valves for compressed, dissolved and other liquefied gases see ISO 10297, ISO 17871 or ISO 17879.

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12493:2020(Main)
LPG equipment and accessories - Welded steel pressure vessels for LPG road tankers - Design and manufacture
SIST EN 12493:2021

This document specifies minimum requirements for materials, design, construction and workmanship procedures, and tests for welded LPG road tanker pressure vessels and their welded attachments manufactured from carbon, carbon/manganese and micro alloy steels.
There is no upper size limit as this is determined by the gross vehicle weight limitation.
This document does not cover pressure vessels for pressure vessel containers.
NOTE 1 In the context of this document, the term "road tanker" is understood to mean "fixed tanks" and "demountable tanks" as defined in ADR.
NOTE 2 The equipment for the pressure vessels and the inspection and testing after assembly is covered by EN 12252 and EN 14334, respectively.
NOTE 3 The design type of the road tanker is subject to approval by the competent authority, as required by ADR.
NOTE 4 This document is intended for LPG only; however, for other liquefied gases see EN 14025.

  • Standard
    58 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16728:2016+A2:2020(Main)
LPG equipment and accessories - Transportable refillable LPG cylinders other than traditional welded and brazed steel cylinders - Periodic inspection
SIST EN 16728:2016+A2:2020

This European Standard specifies procedures for periodic inspection and testing, for transportable refillable LPG cylinders with a water capacity from 0,5 l up to and including 150 l.
This European Standard is applicable to the following:
-   welded steel LPG cylinders manufactured to an alternative design and construction, see EN 14140 or equivalent standard;
-   welded aluminium LPG cylinders, see EN 13110 or equivalent standard;
-   composite LPG cylinders, see EN 14427 or equivalent standard;
-   over-moulded cylinders designed and manufactured according to EN 1442 or EN 14140, see Annex F.
NOTE   The requirements of RID/ADR take precedence over those of this standard in the case of cylinders complying with that regulation, including pi marked cylinders.
This European Standard does not apply to cylinders permanently installed in vehicles.

  • Standard
    50 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1440:2016+A2:2020(Main)
LPG equipment and accessories - Transportable refillable traditional welded and brazed steel Liquefied Petroleum Gas (LPG) cylinders - Periodic inspection
SIST EN 1440:2016+A2:2020

This European Standard specifies procedures for the periodic inspection and testing, of transportable refillable LPG cylinders with a water capacity from 0,5 l up to and including 150 l.
This European Standard is applicable to welded and brazed steel LPG cylinders with a specified minimum wall thickness designed according to EN 1442, EN 12807, EN 13322-1, or equivalent standard (e.g. national codes).
This European Standard is intended to be applied to cylinders complying with RID/ADR (including pi marked cylinders) and also to existing non RID/ADR cylinder populations.
NOTE   The requirements of RID/ADR take precedence over those of this standard in the case of cylinders complying with that regulation, including pi marked cylinders.
This European Standard does not apply to cylinders permanently installed in vehicles.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12807:2019(Main)
LPG equipment and accessories - Transportable refillable brazed steel cylinders for liquefied petroleum gas (LPG) - Design and construction
SIST EN 12807:2019

This document specifies the minimum requirements for the design, construction and testing during manufacture of transportable refillable brazed steel Liquefied Petroleum Gas (LPG) cylinders, of water capacity from 0,5 l up to and including 15 l, exposed to ambient temperatures.
This document applies only to cylinders having a circular cross-section without any longitudinal joint.

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day