LPG equipment and accessories - Procedure for checking transportable refillable LPG cylinders before, during and after filling

This document specifies the procedures to be adopted when checking transportable refillable LPG cylinders before, during and after filling.
This document is applicable to transportable refillable LPG cylinders of water capacity not exceeding 150 l and deemed to be fitted with valves designed according to EN ISO 14245 [4] and EN ISO 15995 [5].
This document does not apply to the requirements for filling LPG cylinders that are designed and equipped for filling by the user.
This document does not apply to the requirements for filling LPG containers on vehicles.
This document is applicable to the following:
—   welded and brazed steel LPG cylinders with a specified minimum wall thickness (see EN 1442 and EN 12807 [1] or an equivalent standard);
—   welded steel LPG cylinders without specified minimum wall thickness (see EN 14140 or an equivalent standard);
—   welded aluminium LPG cylinders (see EN 13110 [2] or an equivalent standard);
—   composite LPG cylinders (see EN 14427 or an equivalent standard); and
—   over-moulded cylinders (OMC).
Specific requirements for the different types of cylinders are detailed in Annex A, Annex B, Annex C, Annex D and Annex G.
This document is intended to be applicable to cylinders complying with RID/ADR [6] [7] (including pi marked cylinders) and also to existing non RID/ADR cylinder populations.

Flüssiggas-Geräte und Ausrüstungsteile - Kontrollverfahren für Flaschen für Flüssiggas (LPG) vor, während und nach dem Füllen

Dieses Dokument legt die Verfahren zur Überprüfung von ortsbeweglichen, wiederbefüllbaren Flaschen für Flüssiggas (LPG, en: liquefied petroleum gas) vor, während und nach dem Füllen fest.
Dieses Dokument ist für ortsbewegliche, wiederbefüllbare Flaschen für Flüssiggas (LPG) mit einem Fassungsraum von höchstens 150 l anwendbar, die mit Ventilen nach EN ISO 14245 [4] und EN ISO 15995 [5] ausgestattet werden.
Dieses Dokument ist nicht anzuwenden für die Anforderungen für das Füllen von Flaschen für Flüssiggas (LPG), die für das Füllen durch den Benutzer ausgelegt und ausgerüstet sind.
Dieses Dokument ist nicht anzuwenden für die Anforderungen für das Füllen von Behältern für Flüssiggas (LPG) auf Fahrzeugen.
Dieses Dokument ist anzuwenden für Folgendes:
—   geschweißte und hartgelötete Flaschen aus Stahl für Flüssiggas (LPG) mit festgelegter Mindest-wanddicke (siehe EN 1442 und EN 12807 [1] oder eine gleichwertige Norm);
—   geschweißte Flaschen aus Stahl für Flüssiggas (LPG) ohne festgelegte Mindestwanddicke (siehe EN 14140 oder eine gleichwertige Norm);
—   geschweißte Flaschen aus Aluminium für Flüssiggas (LPG) (siehe EN 13110 [2] oder eine gleichwertige Norm);
—   Flaschen aus Verbundwerkstoff für Flüssiggas (LPG) (siehe EN 14427 oder eine gleichwertige Norm); und
—   umformte Flaschen (OMC, en: over moulded cylinders).
Spezifische Anforderungen für verschiedene Flaschentypen sind in Anhang A, Anhang B, Anhang C, Anhang D und Anhang G beschrieben.
Dieses Dokument ist für die Anwendung bei Flaschen nach RID/ADR [6] [7] (einschließlich Flaschen mit Pi Kennzeichnung) vorgesehen, sowie für bestehende Flaschengruppen, die nicht RID/ADR entsprechen.

Équipements pour GPL et leurs accessoires - Procédure de vérification des bouteilles transportables et rechargeables pour GPL avant, pendant et après le remplissage

Le présent document décrit les procédures à employer lors de la vérification des bouteilles pour GPL transportables et rechargeables, avant, pendant et après le remplissage.
Le présent document s'applique aux bouteilles transportables et rechargeables pour gaz de pétrole liquéfié (GPL), d'une capacité en eau ne dépassant pas 150 l et réputées être équipées de robinets conçus conformément à l'EN ISO 14245 [4] et à l'EN ISO 15995 [5].
Le présent document ne s'applique pas aux exigences de remplissage des bouteilles pour GPL conçues et équipées pour être remplies par l'utilisateur.
Le présent document ne s'applique pas aux exigences concernant le remplissage de réservoirs GPL sur les véhicules.
Le présent document s'applique aux éléments suivants :
   bouteilles pour GPL en acier soudé et brasé, avec une épaisseur minimale de paroi définie (voir l'EN 1442 et l'EN 12807 [1] ou une norme équivalente) ;
   bouteilles pour GPL en acier soudé, sans épaisseur minimale de paroi définie (voir l'EN 14140 ou une norme équivalente) ;
   bouteilles pour GPL en aluminium soudé (voir l'EN 13110 [2] ou une norme équivalente) ;
   bouteilles pour GPL en matériau composite (voir l'EN 14427 ou une norme équivalente) ; et
   bouteilles surmoulées (OMC).
Les exigences spécifiques relatives aux différents types de bouteilles sont décrites en détail dans les Annexes A, B, C, D et G.
Il est prévu que le présent document soit applicable à des bouteilles conformes au RID/ADR [6] [7] (y compris les bouteilles comportant un marquage pi), ainsi qu'aux familles de bouteilles existantes non conformes au RID/ADR.

Oprema in pribor za utekočinjeni naftni plin (UNP) - Postopek za preverjanje premičnih, ponovno polnjivih jeklenk za UNP pred polnjenjem, med njim in po njem

Ta dokument določa postopke, ki jih je treba sprejeti pri preverjanju prenosnih ponovno polnljivih jeklenk za utekočinjeni naftni plin, pred in med polnjenjem ter po polnjenju.
Ta dokument se uporablja za prenosne ponovno polnljive jeklenke za utekočinjeni naftni plin s prostornino vode, ki ne presega 150 l, za katere je predvideno, da so opremljene z ventili, zasnovanimi v skladu s standardoma EN ISO 14245 [4] in EN ISO 15995 [5].
Ta dokument ne zajema zahtev za polnjenje jeklenk za utekočinjeni naftni plin, ki so zasnovane in opremljene za polnjenje s strani uporabnika.
Ta dokument ne zajema zahtev za polnjenje posod za utekočinjeni naftni plin na vozilih.
Ta dokument se uporablja za naslednje izdelke:   
–   varjene in trdo spajkane jeklenke za utekočinjeni naftni plin iz jekla z določeno minimalno debelino stene (glej standarda EN 1442 in EN 12807 [1] ali enakovreden standard);
–   varjene jeklenke za utekočinjeni naftni plin iz jekla brez določene minimalne debeline stene (glej standard EN 14140 ali enakovreden standard);
–   varjene jeklenke za utekočinjeni naftni plin iz aluminija (glej standard EN 13110 [2] ali enakovreden standard);
–   kompozitne jeklenke za utekočinjeni naftni plin (glej standard EN 14427 ali enakovreden standard); in
–   prelite jeklenke (OMC).
Posebne zahteve za različne vrste jeklenk so podrobno opisane v dodatku A, dodatku B, dodatku C, dodatku D in dodatku G.
Ta osnutek standarda se uporablja za jeklenke v skladu z določbami RID/ADR [6][7] (vključno z jeklenkami z oznako pi) in tudi za obstoječe jeklenke, ki niso v skladu z določbami RID/ADR.

General Information

Status
Published
Publication Date
26-Oct-2021
Withdrawal Date
29-Apr-2022
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
27-Oct-2021
Due Date
13-Apr-2022
Completion Date
27-Oct-2021

Relations

Buy Standard

Standard
EN 1439:2022 - BARVE
English language
35 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN 1439:2020 - BARVE
English language
36 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 1439:2022
01-januar-2022
Nadomešča:
SIST EN 1439:2018
Oprema in pribor za utekočinjeni naftni plin (UNP) - Postopek za preverjanje
premičnih, ponovno polnjivih jeklenk za UNP pred polnjenjem, med njim in po
njem
LPG equipment and accessories - Procedure for checking transportable refillable LPG
cylinders before, during and after filling
Flüssiggas-Geräte und Ausrüstungsteile - Kontrollverfahren für Flaschen für Flüssiggas
(LPG) vor, während und nach dem Füllen
Équipements pour GPL et leurs accessoires - Procédure de vérification des bouteilles
transportables et rechargeables pour GPL avant, pendant et après le remplissage
Ta slovenski standard je istoveten z: EN 1439:2021
ICS:
23.020.35 Plinske jeklenke Gas cylinders
SIST EN 1439:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 1439:2022

---------------------- Page: 2 ----------------------
SIST EN 1439:2022


EN 1439
EUROPEAN STANDARD

NORME EUROPÉENNE

October 2021
EUROPÄISCHE NORM
ICS 23.020.35 Supersedes EN 1439:2017
English Version

LPG equipment and accessories - Procedure for checking
transportable refillable LPG cylinders before, during and
after filling
Équipements pour GPL et leurs accessoires - Procédure Flüssiggas-Geräte und Ausrüstungsteile -
de vérification des bouteilles transportables et Kontrollverfahren für Flaschen für Flüssiggas (LPG)
rechargeables pour GPL avant, pendant et après le vor, während und nach dem Füllen
remplissage
This European Standard was approved by CEN on 6 September 2021.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1439:2021 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN 1439:2022
EN 1439:2021 (E)
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 6
4 Segregation of cylinders prior to filling . 7
4.1 General. 7
4.2 Cylinders suitable for filling . 8
4.3 Cylinders for periodic inspection. 8
4.4 Cylinders requiring further assessment . 8
5 Reassessment of cylinders. 8
6 Filling conditions .
...

SLOVENSKI STANDARD
oSIST prEN 1439:2020
01-december-2020
Oprema in pribor za utekočinjeni naftni plin (UNP) - Postopek za preverjanje
premičnih, ponovno polnjivih jeklenk za UNP pred polnjenjem, med njim in po
njem
LPG equipment and accessories - Procedure for checking transportable refillable LPG
cylinders before, during and after filling
Flüssiggas-Geräte und Ausrüstungsteile - Kontrollverfahren für Flaschen für Flüssiggas
(LPG) vor, während und nach dem Füllen
Équipements pour GPL et leurs accessoires - Procédure de vérification des bouteilles
transportables et rechargeables pour GPL avant, pendant et après le remplissage
Ta slovenski standard je istoveten z: prEN 1439
ICS:
23.020.35 Plinske jeklenke Gas cylinders
oSIST prEN 1439:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 1439:2020

---------------------- Page: 2 ----------------------
oSIST prEN 1439:2020


DRAFT
EUROPEAN STANDARD
prEN 1439
NORME EUROPÉENNE

EUROPÄISCHE NORM

December 2020
ICS 23.020.35 Will supersede EN 1439:2017
English Version

LPG equipment and accessories - Procedure for checking
transportable refillable LPG cylinders before, during and
after filling
Équipements pour GPL et leurs accessoires - Procédure Flüssiggas-Geräte und Ausrüstungsteile -
de vérification des bouteilles transportables et Kontrollverfahren für Flaschen für Flüssiggas (LPG)
rechargeables pour GPL avant, pendant et après le vor, während und nach dem Füllen
remplissage
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 286.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 1439:2020 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 1439:2020
prEN 1439:2020 (E)
Contents Page
European foreword . 3
Introduction . 4
Annex A (normative) Specific requirements for welded and brazed steel LPG cylinders . 10
Annex B (normative) Specific requirements for welded steel LPG cylinders in accordance
with EN 14140 or equivalent standard . 13
B.1 General. 13
B.2 Procedure for establishing rejection criteria for carbon steel cylinders . 13
B.3 Rejection criteria for stainless steel cylinders . 15
Annex C (normative) Specific requirements for welded aluminium LPG cylinders . 18
Annex D (normative) Specific requirements for composite LPG cylinders . 21
D.1 Rejection criteria .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.