EN 13967:2012/FprA1:2016
(Amendment)Flexible sheets for waterproofing - Plastic and rubber damp proof sheets including plastic and rubber basement tanking sheet - Definitions and characteristics
Flexible sheets for waterproofing - Plastic and rubber damp proof sheets including plastic and rubber basement tanking sheet - Definitions and characteristics
The scope of this amendment includes:
- the introduction of CPR requirements (e.g. Annex ZA, clause 6)
- removal of Product Data Sheets descriptions (e.g. clause 7 and Annex D)
- reference to CEN/TR 16625 for MLV/MDV
- correction of minor editorial issues.
Abdichtungsbahnen - Kunststoff- und Elastomerbahnen für die Bauwerksabdichtung gegen Bodenfeuchte und Wasser - Definitionen und Eigenschaften
Feuilles souples d'étanchéité - Feuilles plastiques et élastomères empêchant les remontées capillaires du sol - Définitions et caractéristiques
Hidroizolacijski trakovi - Polimerni in elastomerni tesnilni trakovi za temelje - Definicije in lastnosti
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-november-2016
Hidroizolacijski trakovi - Polimerni in elastomerni tesnilni trakovi za temelje -
Definicije in lastnosti
Flexible sheets for waterproofing - Plastic and rubber damp proof sheets including plastic
and rubber basement tanking sheet - Definitions and characteristics
Abdichtungsbahnen - Kunststoff- und Elastomerbahnen für die Bauwerksabdichtung
gegen Bodenfeuchte und Wasser - Definitionen und Eigenschaften
Feuilles souples d'étanchéité - Feuilles plastiques et élastomères empêchant les
remontées capillaires du sol - Définitions et caractéristiques
Ta slovenski standard je istoveten z: EN 13967:2012/FprA1:2016
ICS:
01.040.91 Gradbeni materiali in gradnja Construction materials and
(Slovarji) building (Vocabularies)
91.100.50 Veziva. Tesnilni materiali Binders. Sealing materials
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
FINAL DRAFT
EUROPEAN STANDARD
EN 13967:2012
NORME EUROPÉENNE
EUROPÄISCHE NORM
FprA1
September 2016
ICS 01.040.91; 91.100.50
English Version
Flexible sheets for waterproofing - Plastic and rubber
damp proof sheets including plastic and rubber basement
tanking sheet - Definitions and characteristics
Feuilles souples d'étanchéité - Feuilles plastiques et Abdichtungsbahnen - Kunststoff- und
élastomères empêchant les remontées capillaires du Elastomerbahnen für die Bauwerksabdichtung gegen
sol - Définitions et caractéristiques Bodenfeuchte und Wasser - Definitionen und
Eigenschaften
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical
Committee CEN/TC 254.
This draft amendment A1, if approved, will modify the European Standard EN 13967:2012. If this draft becomes an amendment,
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13967:2012/FprA1:2016:2016 E
worldwide for CEN national Members.
European foreword
This document (EN 13967:2012/FprA1:2016) has been prepared by Technical Committee CEN/TC 254
“Flexible sheets for waterproofing”, the secretariat of which is held by NEN.
This document is currently submitted to the Unique Acceptance Procedure.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Regulation.
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this
document.
1 Modifications to Clause 2, Normative references
Replace:
"EN 12311-2 Flexible sheets for waterproofing - Determination of tensile properties - Part 2: Plastic and
rubber sheets for roof waterproofing"
with:
"EN 12311-2:2013 Flexible sheets for waterproofing - Determination of tensile properties - Part 2: Plastic
and rubber sheets for roof waterproofing"
Replace "EN 12730:2001" with "EN 12730:2015".
Replace "EN 13859-1:2010" with "EN 13859-1:2014".
Add:
"CEN/TR 16625:2013 Flexible sheets for waterproofing - Statistical definition of manufacturer's limiting
value and declared value (MLV and MDV) - 95 % Statistic"
2 Modifications to Clause 3, Terms and definitions
In definition 3.4, manufacturer's limiting value, replace:
"value stated by the manufacturer to be met during testing
Note 1 to entry: The manufacturer's limiting value can be a minimum value or a maximum value, according to
statements made under product characteristics of this standard."
with:
"nominal value including a single sided specification according to the product standard for a given test
method or property
Note 1 to entry: The MLV can be a minimum or a maximum value according to statements made under product
characteristics of the relevant product standard.
[CEN/TR 16625:2013, 2.2]"
In definition 3.5, manufacturer's declared value, replace:
"value declared by the manufacturer accompanied by a declared tolerance"
with:
"nominal value including double sided specification according to the product standard for a given test
method or property
[CEN/TR 16625:2013, 2.1]"
Add the following new term:
"3.13
overpack
outer container or packaging designed to enclose on secure one or more inner containers or
packagings"
3 Modification to 5.1 General
Add the following sub-clause:
"5.1.3 Manufacturer's limiting value (MLV) and declared value (MDV) shall be defined in accordance
with CEN/TR 16625."
4 Modification to 5.5, Thickness and mass per unit area
st
In the 1 sentence, replace:
"The thickness and mass per unit area shall be determined in accordance with EN 1849-2."
with:
"The thickness or mass per unit area shall be determined in accordance with EN 1849-2."
5 Modification to the heading of 5.8
Replace:
"5.8 Durability"
with:
"5.8 Durability of water tightness"
6 Modification to 5.10, Resistance to tearing (nail shank)
Replace the whole sub-clause with the following:
"Tear resistance (nail shank) shall be determined in accordance with EN 12310-1 and shall be greater
or equal to the manufacturer limiting value.".
7 Modification to 5.13, Resistance to static loading
Replace the whole sub-clause with the following:
"The resistance to static loading shall be determined in accordance with Method C of EN 12730:2015
and shall be greater than or equal to the manufacturer's limiting value.
If required the resistance to static loading shall be determined in accordance with Method A of
EN 12730:2015 and shall be greater than or equal to the manufacturer's limiting value."
8 Modification to 5.14, Tensile properties
Replace the whole sub-clause with the following:
"Type T and A:
The tensile properties for unreinforced sheets as homogenous sheets and sheets with a non-woven
inner layer (e.g. fibre glass mat) of less than or equal to 80 g/m shall be determined in accordance with
Method B of EN 12311-2:2013. For all other sheets Method A of EN 12311-2:2013 shall be used to
determine tensile properties.
Type V:
The tensile properties of unreinforced sheets shall be determined in accordance with EN 12311-2:2013
Method B and shall be greater than or equal to the manufacturer's limiting value for the longitudinal
and transverse directions of the sheet. The tensile properties of reinforced sheets shall be determined
in accordance with EN 13859-1:2014, Annex A.
For all types T, A and V the tensile properties shall be greater than or equal to the manufacturer's
limiting value for the longitudinal and transverse directions of the sheet."
9 Modification to 5.16, Reaction to fire
Add the following item e):
"e) Test results from EN ISO 11925-2 for a given product with edge exposure shall apply to surface
exposure."
10 Modification to 5.17, Dangerous substances
Replace the whole sub-clause with the following:
"National regulations on dangerous substances may require verification and declaration on release, and
sometimes content, when construction products covered by this standard are placed on those markets.
Verification and declaration on release/content should be done taking into account national provisions
in the place of use.
NOTE 1 An informative database covering European and national provisions on dangerous substances is
available at the Construction web site on EUROPA accessed through:
http://ec.europa.eu/enterprise/construction/cpd-ds/
NOTE 2 Experience has shown that products which have the same polymeric base as the components of the
leaching apparatus specified in CEN/TS 16637-2 leach less than the detection limit of this method."
11 Modification to Clause 6
Replace the whole clause with the following:
"6 Assessment and verification of constancy of performance - AVCP
6.1 General
The compliance of plastic and rubber damp proof sheets including plastic and rubber basement tanking
sheets with the requirements of this standard and with the performances declared by the manufacturer
in the DoP shall be demonstrated by:
— determination of the product type;
— factory production control by the manufacturer, including product assessment.
The manufacturer shall always retain the overall control and shall have the necessary means to take
responsibility for the conformity of the product with its declared performance(s).
NOTE The assignment of tasks to the notified body(ies) and the manufacturer is shown in Annex ZA, Tables
ZA.3.
6.2 Type testing
6.2.1 General
All performances related to characteristics included in this standard shall be determined when the
manufacturer intends to declare the respective performances unless the standard gives provisions for
declaring them without performing tests (e.g. use of previously existing data, CWFT and conventionally
accepted performance).
The performance of the characteristics shall be tested at the beginning of the production of a new
product type (unless a member of the same family) or at the beginning of a new method of production
(where this may affect the stated properties).
Whenever a change occurs in the product design, the raw material, supplier of the components or the
production process (subject to the definition of a family) which would change significantly one or more
of the characteristics, the type tests shall be repeated for the appropriate characteristic(s).
Assessment previously performed in accordance with the provisions of this standard, may be taken into
account provided that they were made to the same or a more rigorous test method, under the same
AVCP system on the same product or products of similar design, construction and functionality, such
that the results are applicable to the product in question.
For the purposes of assessment, the manufacturer's products may be grouped into families, where it is
considered that the results for one or more characteristics from any one product within the family are
representative for these same characteristics for all products within that same family.
NOTE 1 Products may be grouped in different families for different characteristics.
NOTE 2 It is advised to make reference to the assessment method standards to allow the selection of a suitable
representative sample.
In addition, the determination of the product type shall be performed for all characteristics included in
the standard for which the manufacturer declares the performance in the DOP:
— at the beginning of the production of a new or modified plastic and rubber damp proof sheets
including plastic and rubber basement tanking sheets (unless a member of the same product
range), or
— at the beginning of a new or modified method of production (where this may affect the stated
properties); or
— they shall be repeated for the appropriate characteristic(s), whenever a change occurs in the plastic
and rubber damp proof sheets including plastic and rubber basement tanking sheets design, in the
raw material or in the supplier of the components, or in the method of production (subject to the
definition of a family), which would affect significantly one or more of the characteristics.
Where components are used whose characteristics have already been determined, by the component
manufacturer, on the basis of assessment methods of other product standards, these characteristics
need not be re-assessed. The specifications of these components shall be documented.
Products bearing regulatory marking in accordance with appropriate harmonized European
specifications may be presumed to have the performances declared in the DoP, although this does not
replace the responsibility on plastic and rubber damp proof sheets including plastic and rubber
basement tanking sheets manufacturer to ensure that these sheets as a whole are correctly
manufactured and their component products have the declared performance values.
6.2.2 Test samples, testing and compliance criteria
The number of samples of plastic and rubber damp proof sheets including plastic and rubber basement
tanking sheets to be tested/assessed shall be in accordance with Table 1.
The tests shall be performed at least once for all characteristics in Table 1. Samples shall be taken in
accordance to EN 13416, the number of specimen shall be in accordance to the specific test method.
The statistics of MLV and MDV are defined in CEN/TR 16625.
Table 1 — Compliance criteria
Product Parameter Test Sub-clause Compliance
methods in this criteria
Characteristics (where
Type
document (where
required)
A V T
required)
Water tightness to liquid * * *
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.