EN 13169:2012+A1:2015/prA2
(Amendment)Thermal insulation products for buildings - Factory made expanded perlite board (EPB) products - Specification
Thermal insulation products for buildings - Factory made expanded perlite board (EPB) products - Specification
DOW = DAV + 21 months
Wärmedämmstoffe für Gebäude - Werkmäßig hergestellte Produkte aus Blähperlit (EPB) - Spezifikation
Produits isolants thermiques pour le bâtiment - Produits manufacturés en panneaux de perlite expansée (EPB) - Spécification
Toplotnoizolacijski proizvodi za stavbe - Proizvodi iz ekspandiranega perlita (EPB) - Specifikacija
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-november-2018
Toplotnoizolacijski proizvodi za stavbe - Proizvodi iz ekspandiranega perlita (EPB)
- Specifikacija
Thermal insulation products for buildings - Factory made expanded perlite board (EPB)
products - Specification
Wärmedämmstoffe für Gebäude - Werkmäßig hergestellte Produkte aus Blähperlit (EPB)
- Spezifikation
Produits isolants thermiques pour le bâtiment - Produits manufacturés en panneaux de
perlite expansée (EPB) - Spécification
Ta slovenski standard je istoveten z: EN 13169:2012+A1:2015/prA2
ICS:
91.100.60 0DWHULDOL]DWRSORWQRLQ Thermal and sound insulating
]YRþQRL]RODFLMR materials
SIST EN en,fr,de
13169:2013+A1:2015/oprA2:2018
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT
EUROPEAN STANDARD
EN 13169:2012+A1:2015
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA2
September 2018
ICS 91.100.60
English Version
Thermal insulation products for buildings - Factory made
expanded perlite board (EPB) products - Specification
Produits isolants thermiques pour le bâtiment - Wärmedämmstoffe für Gebäude - Werkmäßig
Produits manufacturés en panneaux de perlite hergestellte Produkte aus Blähperlit (EPB) -
expansée (EPB) - Spécification Spezifikation
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 88.
This draft amendment A2, if approved, will modify the European Standard EN 13169:2012+A1:2015. If this draft becomes an
amendment, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for
inclusion of this amendment into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13169:2012+A1:2015/prA2:2018 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
1 Modification to the European foreword . 4
2 Modification to the Scope . 4
3 Modifications to Clause 2, Normative references . 4
4 Modifications to Clause 3, Terms and definitions . 4
5 Modification to Clause 4, Requirements . 5
6 Modification to 4.1, General . 5
7 Modification to 4.3.10, Water vapour transmission . 5
8 Modification to 4.3.11, Release of dangerous substances . 5
9 Modification to 4.3.13, Continuous glowing combustion . 5
10 Modification to 5.3.4, Water absorption by total immersion . 5
11 Modification to Clause 6, Designation code . 7
12 Modification to Clause 7, Assessment and Verification of the Constancy of
Performance (AVCP) . 7
13 Modification to Clause 8, Marking and labelling . 7
14 Modification to A.1, General . 8
15 Modification to A.2, Input data . 8
16 Modification to Annex B, Product type determination (PTD) and factory production
control (FPC) . 8
17 Modification to D.1, Requirements . 12
18 Modification to D.2.1.1, General . 12
19 Modification to D.2.1.3, Length and width, thickness, squareness, flatness . 12
20 Modification to E.2, Requirements . 12
21 Modification to E.2.12, Release of dangerous substances . 12
22 Modification to E.4, Designation code . 12
23 Modification to E.5, Factory production control . 12
24 Modification to E.7, Marking and labelling . 14
25 Modification to Annex ZA, Clauses of this European Standard addressing the
provisions of the EU Construction Products Regulation . 14
European foreword
This document (EN 13169:2012+A1:2015/prA2:2018) has been prepared by Technical Committee
CEN/TC 88 "Thermal insulating materials and products", the secretariat of which is held by DIN.
This document is currently submitted to the CEN Enquiry.
This document has been prepared under a standardization request given to CEN by the European
Commission and the European Free Trade Association.
For relationship with EU Regulation, see informative Annex ZA which is an integral part of this
document.
1 Modification to the European foreword
In the seventh paragraph, delete ", and supports essential requirements of EU Directive(s)".
Delete the ninth paragraph (list of changes) and replace the tenth and eleventh paragraph with the
following:
"Amendment A2 modifies EN 13169:2012 and its A1 amendment. This amendment introduces or
corrects:
a) A modified Annex ZA;
b) A modified clause “Release of Dangerous substance”;
c) A modified definition for “Class F” in the clause “reaction to fire”;
d) Editorial modifications in different parts of the text and linked to the above modifications;
e) Modifications to be in line with the CPR, e.g. PTD replaced by Type Testing;
f) Delete reference to EN 12086 and replace with EN ISO 12572;
g) Delete § 4.3.14 Continuous glowing combustion.
In the fourteenth paragraph, add the following standard to the end of the list of standards:
"EN 16069, Thermal insulation products for buildings — Factory made products of polyethylene foam
(PEF) — Specification".
2 Modification to the Scope
In the first paragraph, replace the word "requirements“ with the word "characteristics“.
In the fourth paragraph, replace the term "evaluation of conformity" with "assesment and verification of
constancy of performance (AVCP)".".
3 Modifications to Clause 2, Normative references
Delete the reference "EN 12086:1997".
Add the following refererences:
"EN 16516, Construction products — Assessment of release of dangerous substances – Determination of
emissions into indoor air"
and
"EN ISO 12572, Thermal insulating products for building applications — Determination of water vapour
transmission properties".
4 Modifications to Clause 3, Terms and definitions
Delete the terms "3.1.2 level“ and "3.1.3 class“ and renumber the remaining terms accordingly.
Delete the abbreviated terms "PTD" and "VCP".
5 Modification to Clause 4, Requirements
Replace the term "Requirements“ with "Characteristics“.
6 Modification to 4.1, General
Please replace the text in the clause with the following:
"Product properties shall be assessed in accordance with Clause 5. To comply with this standard,
products shall meet the characteristics of 4.2, and the characteristics of 4.3 as appropriate.
For multilayered insulation products additional characteristics are given in Annex D.
For composite insulation products additional characteristics are given in Annex E.
One test result on a product property is the average of the measured values on the number of test
specimens given in Table 7.
NOTE Information on additional properties is given in Annex F.".
7 Modification to 4.3.10, Water vapour transmission
Replace the reference to "EN 12086" with a reference to "EN ISO 12572".
8 Modification to 4.3.11, Release of dangerous substances
Replace the text in the clause with the following:
1)
"If the release of dangerous substances into indoor air is tested, this shall be done according to
EN 16516.
NOTE An informative database covering European and national provisions on dangerous substances is
available at the Construction web site on EUROPA accessed through: http://ec.europa.eu/growth/tools-
databases/cp-ds.".
9 Modification to 4.3.13, Continuous glowing combustion
Delete the whole clause.
10 Modification to 5.3.4, Water absorption by total immersion
Replace Table 7 with the following:
1) See for reference the LCI list of the European Commission « Agreed EU-LCI values »
(http://ec.europa.eu/growth/sectors/construction/eu-lci/values_en).
"Table 7 — Test methods, test specimens and conditions
Dimensions in millimetres
Clause Minimum
number of
Test specimen
Test measureme Specific
length and
method nts to get conditions
No. Title
a
width
one test
result
EN 12667
Thermal resistance – thermal See EN 12667 or
4.2.1 or 1 –
conductivity EN 12939
EN 12939
4.2.2 Length and width EN 822 Full size 1 –
Load:
(250 ± 5) Pa
4.2.3 Thickness EN 823 Full size 3
See 4.2.3
4.2.4 Squareness EN 824 Full size 1 –
4.2.5 Flatness EN 825 Full size 1 –
4.2.6 Bending strength EN 12089 See EN 12089 3 Method B
See EN 13501-1 and EN 15715
Reaction to fire of the product as See Clause 5 of
4.2.7
placed on the market EN 15715:2009
Dimensional stability under
4.3.2 EN 1604 200 × 200 3 –
specified conditions
If d ≤ 100
100 × 100 5
N
Compressive stress or
4.3.3 EN 826
compressive strength
If d > 100
150 × 150 5
N
If d ≤ 100
100 × 100 3
N
Deformation under specified load
4.3.4 EN 1605
and temperature conditions
If d > 100
150 × 150 3
N
See 5.3.3
80 × 80
If board > 1 m
Tensile strength perpendicular to
4.3.5 EN 1607 or
faces
See 5.3.3
100 × 100
If board ≤ 1 m
Short term water absorption by
4.3.6.1 EN 1609 200 × 200 4 Method A
partial immersion
Short term water absorption by
4.3.6.2 See 5.3.4 300 × 300 3 –
total immersion
Bending strength at constant Method B
4.3.7 EN 12089 300 × 50 3
span Span: 250 mm
4.3.8 Point load EN 12430 300 × 300 3 –
If d ≤ 100
100 × 100 3
N
4.3.9 Compressive creep EN 1606
If d > 100
150 × 150 3
N
EN ISO See 6.1 in
4.3.10 Water vapour transmission 3 –
12572 EN 12086:1997
See
4.3.11 Release of dangerous substances EN 16516 See EN 16516 4.3.11
EN 16516
Reaction to fire of the product in
See Clause 6 of
4.3.12 standardized assemblies See EN 13501-1 and EN 15715
EN 15715:2009
simulating end-use applications
a
Full size product thickness except for 4.2.7 when the limits of the test methods are exceeded.
".
11 Modification to Clause 6, Designation code
Replace the first sentence with the following:
"If a designation code is provided, it shall be given as following (including relevant characteristics from
clause 4.3):".
12 Modification to Clause 7, Assessment and Verification of the Constancy of
Performance (AVCP)
Replace the subclauses with the following:
"7.1 General
In accordance with EN 13172, the compliance of the Factory made expanded perlite board with the
requirements of this standard and with the performances declared by the manufacturer in the DoP shall
be demonstrated by:
— determination of the product type (Type testing);
— factory production control by the manufacturer, including product assessment.
The manufacturer sh
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.