CEN/TR 115-3:2017

Safety of escalators and moving walks - Part 3: Correlation between EN 115-1:2008+A1:2010 and EN 115-1:2017

This Technical Report applies to escalators and moving walks built in accordance with EN 115-1:2017.

Sicherheit von Fahrtreppen und Fahrsteigen - Teil 3: Übereinstimmung zwischen EN 115-1:2008+A1:2010 und EN 115-1:2017

Sécurité des escaliers mécaniques et trottoirs roulants - Partie 3 : Corrélation entre l'EN 115-1:2008+A1:2010 et l'EN 115-1:2017

Le présent Rapport technique s'applique aux escaliers mécaniques et trottoirs roulants construits conformément à l'EN 115-1:2017

Varnost tekočih stopnic in tekočih stez - 3. del: Medsebojna odvisnost med EN 115:2008+A1:2010 in EN 115-1:2017

To tehnično poročilo se nanaša na tekoče stopnice in tekoče steze, zgrajene v skladu s standardom EN 115-1:2017.

General Information

• Status: Published
• Publication Date: 21-Nov-2017
• ICS: 91.140.90 - Lifts. Escalators
• Technical Committee: CEN/TC 10 - Passenger, goods and service lifts
• Drafting Committee: CEN/TC 10/WG 2 - Escalators and passenger conveyors
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 22-Nov-2017
• Due Date: 26-Dec-2018
• Completion Date: 22-Nov-2017
• Ref Project: SIST-TP CEN/TR 115-3:2018 - Safety of escalators and moving walks - Part 3: Correlation between EN 115-1:2008+A1:2010 and EN 115-1:2017

Relations

• Replaces: CEN/TR 115-3:2009 - Safety of escalators and moving walks - Part 3: Correlation between EN 115:1995 and its amendments and EN 115-1:2008
• Effective Date: 06-Dec-2017

Standards Content (Sample)

SLOVENSKI STANDARD
01-maj-2018
1DGRPHãþD
SIST-TP CEN/TR 115-3:2010
9DUQRVWWHNRþLKVWRSQLFLQWHNRþLKVWH]GHO0HGVHERMQDRGYLVQRVWPHG(1
$LQ(1
Safety of escalators and moving walks - Part 3: Correlation between EN 115-
1:2008+A1:2010 and EN 115-1:2017
Sicherheit von Fahrtreppen und Fahrsteigen - Teil 3: Übereinstimmung zwischen EN 115
-1:2008+A1:2010 und EN 115-1:2017
Sécurité des escaliers mécaniques et trottoirs roulants - Partie 3 : Corrélation entre l'EN
115-1:2008+A1:2010 et l'EN 115-1:2017
Ta slovenski standard je istoveten z: CEN/TR 115-3:2017
ICS:
91.140.90 'YLJDOD7HNRþHVWRSQLFH Lifts. Escalators
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

CEN/TR 115-3
TECHNICAL REPORT
RAPPORT TECHNIQUE
November 2017
TECHNISCHER BERICHT
ICS 91.140.90 Supersedes CEN/TR 115-3:2009
English Version
Safety of escalators and moving walks - Part 3: Correlation
between EN 115-1:2008+A1:2010 and EN 115-1:2017
Sécurité des escaliers mécaniques et trottoirs roulants Sicherheit von Fahrtreppen und Fahrsteigen - Teil 3:
- Partie 3 : Corrélation entre l'EN 115-1:2008+A1:2010 Übereinstimmung zwischen EN 115-1:2008+A1:2010
et l'EN 115-1:2017 und EN 115-1:2017

This Technical Report was approved by CEN on 22 October 2017. It has been drawn up by the Technical Committee CEN/TC 10.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TR 115-3:2017 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
Introduction . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 List of significant hazards . 5
5 Correlation between EN 115-1:2017 and EN 115-1:2008+A1:2010 and vice versa . 5
Bibliography . 31

European foreword
This document (CEN/TR 115-3:2017) has been prepared by Technical Committee CEN/TC 10 “Lifts,
escalators and moving walks”, the secretariat of which is held by AFNOR.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document supersedes CEN/TR 115-3:2009.
The reason for the revision of CEN/TR 115-3 was the publication of EN 115-1:2017. CEN/TR 115-3:2009
compared EN 115-1:1995, including amendments A1 and A2, with EN 115-1:2008. CEN/TR 115-3:2017
compares EN 115-1:2017 with EN 115-1:2008+A1:2010.
Introduction
This Technical Report has been prepared to allow the user to compare the existing standard
EN 115-1:2017 with the EN 115-1:2008+A1:2010 and vice versa.
1 Scope
This Technical Report applies to escalators and moving walks built in accordance with EN 115-1:2017.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
EN 115-1:2008+A1:2010, Safety of escalators and moving walks - Part 1: Construction and installation
EN 115-1:2017, Safety of escalators and moving walks - Part 1: Construction and installation
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 115-1:2017 and
EN 115-1:2008+A1:2010 apply.
4 List of significant hazards
For the purpose of this document, the list of significant hazards given in EN 115-1:2017 and
EN 115-1:2008+A1:2010 apply.
5 Correlation between EN 115-1:2017 and EN 115-1:2008+A1:2010 and vice
versa
This Technical Report is presented in the form of two tables. Table 1 provides a correlation between
EN 115-1:2008+A1:2010 and EN 115-1:2017 based upon the chronological clause references of
EN 115-1:2008+A1:2010. Table 2 provides a similar correlation but using EN 115-1:2017 as the base
document for comparison.
Each clause is cross-referenced to its equivalent clause and the table illustrates the status of the text or
requirement. Guidance is given on whether the clause has remained unchanged, is modified, is new or
has been deleted.
Where appropriate a short explanation is given in the “Remarks” column to highlight changes and new
requirements contained in the revision of EN 115-1:2017.
Table 1 — Correlation between EN 115-1:2008+A1:2010 and EN 115-1:2017
EN 115-1:2008+A1:2010 EN 115-1:2017 Remarks
Introduction Introduction  x
1 Scope 1 Scope
1.1 1.1 x
Requirements for seismic
1.2 - x activities included in
Annex M.
1.3 1.2 x
2 Normative references 2 Normative references  x   Updated.
3 Terms and definitions 3 Terms and definitions
3.1.1 3.1.1 x
- 3.1.2   x
3.1.2 3.1.3 x
3.1.3 3.1.4 x
3.1.4 3.1.5 x
3.1.5 a 3.1.6 x
3.1.5 b 3.1.7 x
- 3.1.8   x
Term changed, definition the
3.1.6 3.1.27 x
same.
Term changed, definition the
3.1.7 3.1.24 x
same.
3.1.8 3.1.9 x
3.1.9 3.1.10 x
3.1.10 3.1.11 x
3.1.11 3.1.12 x
3.1.12 3.1.13 x
3.1.13 a 3.1.14 x
3.1.13 b 3.1.15 x
Unchanged
Modified
New
Deleted
EN 115-1:2008+A1:2010 EN 115-1:2017 Remarks
3.1.14 3.1.16 x
3.1.15 3.1.17 x
3.1.16 3.1.18 x
3.1.17 3.1.19 x
3.1.18 3.1.20 x
Rated speed not used
3.1.19 3.1.21 x
anymore and deleted.
3.1.20 3.1.26  x   E/E/PE instead of PESSRAE.
3.1.21 -    x
3.1.22 3.1.22 x
3.1.23 3.1.23 x
3.1.24 3.1.25  x   E/E/PE instead of PESSRAE.
3.1.25 3.1.28 x
3.1.26 3.1.29 x
3.1.27 -    x
3.1.28 -    x
- 3.1.30   x
3.2 3.2     Modified
4 List of significant 4 List of significant
hazards hazards
Reference EN ISO 14121-1
4.1 4.1 x obsolete, replaced by
EN ISO 12100.
4.2 4.2 x    “fixed devices” added.
4.3 4.3 x
4.4 4.4 x
4.5 4.5 x
4.6 4.6 x
4.7 4.7 x
Unchanged
Modified
New
Deleted
EN 115-1:2008+A1:2010 EN 115-1:2017 Remarks
4.8 4.8 x
4.9 4.9 x    “stopping” added.
4.10 4.10 x
- 4.11   x
5 Safety requirements 5 Safety requirements
and/or protective/risk and/or protective/risk
reduction measures reduction measures
Reference to Annex M
5.1 5.1  x
(seismic conditions) added.
5.2.1.1 5.2.1.1 x
5.2.1.2 5.2.1.2  x   Definition of gaps added.
5.2.1.3 5.2.1.3 x
5.2.1.4 5.2.1.4 x
5.2.1.5 5.2.1.5 x
5.2.1.6 5.2.1.6 x
5.2.2 5.2.2 x
5.2.3 5.2.3 x
5.2.4 5.2.4  x
Requirements for comb and
5.2.5 5.2.5  x
floor plate deflection added.
5.3.1 5.3.1 x
5.3.2 5.3.2 x
5.3.3.1 5.3.3.1 x
New requirements for
5.3.3.2.1 5.3.3.2.1  x   inserts/fixings and tread
surface on the side.
New requirements for
inserts/fixings and test
5.3.3.2.2 5.3.3.2.2  x
procedure defined more
accurately.
5.3.3.2.3 5.3.3.2.3 x
5.3.3.2.4 5.3.3.2.4 x
Unchanged
Modified
New
Deleted
EN 115-1:2008+A1:2010 EN 115-1:2017 Remarks
5.3.3.3 5.3.3.3 x
5.3.4 5.3.4 x
Measuring procedure
5.3.5 5.3.5  x
defined more accurately
x
5.3.6
5.3.6
Position of the device more
5.12.2.7.11  x
accurately defined.
5.4.1.1 5.4.1.1 x
“Nominal speed” replaced by
5.4.1.2.1 5.4.1.2.1  x   “speed of an unloaded
escalator”.
5.4.1.2.2 5.4.1.2.2 x
5.4.1.2.3 5.4.1.2.3 x
5.4.1.3.1 5.4.1.3.1 x
New requirement for fatigue
life clarified. Driving
5.4.1.3.2 5.4.1.3.2  x
elements defined more
accurately.
5.4.1.4 5.4.1.4 x
Stopping, as the initiation of
5.4.1.5 5.12.3.5.1  x   a braking sequence, defined
more accurately.
5.4.2.1.1 5.4.2.1.1  x
5.4.2.1.1    Improved wording;
condition added for no
5.12.2.7.12    intentional delay.
5.4.2.1.1.1 x
5.12.3.5.2.1
5.12.3.10
Electrical braking added as
- 5.4.2.1.1.2   x
specific type of braking.
5.4.2.1.1.2 5.12.3.5.1  x   Note added.
Unchanged
Modified
New
Deleted
EN 115-1:2008+A1:2010 EN 115-1:2017 Remarks
5.4.2.1.1.1
5.4.2.1.1.2
5.4.2.1.1.3 x
5.4.2.1.1.3
5.4.2.1.1.4 5.4.2.1.1.4 x
5.4.2.1.2
5.4.2.1.2 x
5.12.3.5.1
5.4.2.1.3 5.4.2.1.3 x
5.4.2.2 5.4.2.2
5.4.2.2.1 5.4.2.2.1 x
Butterworth filter added for
5.4.2.2.2 5.4.2.2.2  x
auxiliary brake.
5.4.2.2.3 5.4.2.2.3 x
5.4.2.2.4
5.12.3.5.3
5.4.2.2.4 x
5.12.2.7.4
5.4.2.2.5 5.4.2.2.5 x
5.4.2.3 x
5.12.2.2 x
5.4.2.3.1
5.12.2.7.2 x
5.4.2.3 x
5.12.2.2 x
5.4.2.3.2
5.12.2.7.3 x
5.4.3.1 X
5.4.3.1
5.12.2.7.5 X
5.4.3.2 5.4.3.2 X
5.4.3.3 X
5.4.3.3
5.12.2.7.6 X
Unchanged
Modified
New
Deleted
EN 115-1:2008+A1:2010 EN 115-1:2017 Remarks
5.4.4.1 5.4.4.1 X
5.4.4.2 x
5.4.4.2
5.12.2.7.6 x
5.5 5.5 x
5.5.3 5.5.3 x
5.5.3.1 5.5.3.1 x
5.5.3.2 5.5.3.2 x
Deflection requirement
5.5.3.3 5.5.3.3  x
defined more accurately.
Shape of skirt deflector
defined in more detail.
5.5.3.4 5.5.3.4  x   Materials for friction test
updated, based on modified
referenced standard.
5.5.4 5.5.4 x
5.5.5 5.5.5 x
5.6.1 x
5.6.1
Requirement for detection
5.12.2.7.13  x
time frame updated.
Requirement for clearance
5.6.2.1 5.6.2.1  x   under handrail profile
modified.
5.6.2.2 5.6.2.2 x
5.6.2.3 5.6.2.3 x
5.6.3 5.6.3 x
5.6.4.1 5.6.4.1 x
5.6.4.2 5.6.4.2 x
5.6.4.3 x
5.6.4.3
5.12.2.7.9 x
5.6.5 5.6.5 x
5.7.1 5.7.1 x
Unchanged
Modified
New
Deleted
EN 115-1:2008+A1:2010 EN 115-1:2017 Remarks
5.7.2 5.7.2 x
5.7.2.1 5.7.2.1 x
5.7.2.2 5.7.2.2 x
5.7.2.3 5.7.2.3 x
5.7.2.4 5.7.2.4 x
5.7.2.5 x
5.7.2.5
5.12.2.7.10 x
5.7.3.1 5.7.3.1 x
5.7.3.2 5.7.3.2 x
5.7.3.2.1 5.7.3.2.1 x
5.7.3.2.2 5.7.3.2.2 x
5.7.3.2.3 5.7.3.2.3 x
5.7.3.2.4 5.7.3.2.4 x
5.7.3.2.5 5.7.3.2.5 x
5.7.3.2.6 x
5.7.3.2.6
5.12.2.7.7 x
5.7.3.3 5.7.3.3 x
5.8.1 5.8.1 x
Requirement for standing
5.8.2.1 5.8.2.1  x
area updated.
5.8.2.2 5.8.2.2 x
5.8.2.3 5.8.2.3 x
5.8.3 5.8.3 x
5.8.4 5.12.2.7.17  x
Requirements for test added.
5.9 5.9  x   Sprinkler and water mist
systems added.
5.10 5.10 x
Unchanged
Modified
New
Deleted
EN 115-1:2008+A1:2010 EN 115-1:2017 Remarks
5.11.1 5.11.1 x
5.11.2.1.1 5.11.2.1.1 x
5.11.2.1.2 5.11.2.1.2 x
5.11.2.1.3 5.11.2.1.3  x
- 5.11.2.1.4   x
5.11.2.2 5.11.2.2 x
5.11.3 5.12.1.3 x
5.11.4 5.11.3 x
5.11.5.1
5.11.5.1.1
5.11.5.1.2
5.11.4.1  x
5.11.5.1.3
5.11.5.1.4
5.11.5.1.5
5.11.5.2 5.11.4.2  x
5.11.5.3 5.11.4.3  x
5.11.4.3.1  x   Reference to EN 60204-1.
5.11.4.3.2   x
5.11.5.3.1
5.11.4.3.3   x
5.11.4.3.4   x
Warning label according to
5.11.5.3.2 5.11.4.3.5  x
EN 60204-1.
5.11.5.3.3 5.11.4.3.7  x
5.11.5.4 5.11.4.4  x
5.11.6 5.11.4.3.6  x
5.11.7 5.12.1.5 x
5.12.1.1 -    x
- 5.12.1   x
- 5.12.1.1   x
Unchanged
Modified
New
Deleted
SIST-TP CEN/TR 115-3:2
...