EN 13880-7:2019
(Main)Hot applied joint sealants - Part 7: Function testing of joint sealants
Hot applied joint sealants - Part 7: Function testing of joint sealants
This document describes a function test for hot-applied joint sealants intended to be used in areas where the joints are subjected to combined conditions of temperature ≤ - 20 °C and crack joint movement ≤ 35 % in construction joints as well as in spontaneously formed cracks in road and airfield pavements.
Heiß verarbeitbare Fugenmassen - Teil 7: Funktionsprüfung von Fugenmassen
Dieses Dokument beschreibt eine Funktionsprüfung für heiß verarbeitbare Fugenmassen, die in Bereichen, wo die Fugen kombinierten Bedingungen von Temperaturen ≤ −20 °C und Rissbewegungen ≤ 35 % ausgesetzt sind, in Arbeitsfugen und als Rissfüllungen in Verkehrsflächen anzuwenden sind.
Produits de scellement de joints appliqués à chaud - Partie 7 : Test fonctionnel sur produits de scellement de joints
Cette Norme européenne décrit un test fonctionnel pour les produits de scellement de joints appliqués à chaud destinés à être utilisés sur des surfaces où les joints sont exposés à des conditions combinées de températures ≤ - 20 °C et à des ouvertures de fissures ≤ 35 %, aussi bien dans les joints de construction que dans les fissures apparues en service, sur des chaussées routières et aéronautiques.
Toplo nanosljive tesnilne mase za stike - 7. del: Preskušanje funkcionalnosti tesnilne mase za stike
Ta evropski standard opisuje preskus funkcionalnosti za toplo nanosljive tesnilne mase za stike, ki se uporabljajo v območjih, kjer so stiki izpostavljeni kombiniranim pogojem temperature ≤ –20 °C in gibanjem razpok v stiku ≤ 35 % v gradbenih stikih, ter spontano nastalih razpokah na cesti in letalski stezi.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-julij-2019
Nadomešča:
SIST EN 13880-7:2004
Toplo nanosljive tesnilne mase za stike - 7. del: Preskušanje funkcionalnosti
tesnilne mase za stike
Hot applied joint sealants - Part 7: Function testing of joint sealants
Heiß verarbeitbare Fugenmassen - Teil 7: Funktionsprüfung von Fugenmassen
Produits de scellement de joints appliqués à chaud - Partie 7 : Test fonctionnel sur
produits de scellement de joints
Ta slovenski standard je istoveten z: EN 13880-7:2019
ICS:
91.100.50 Veziva. Tesnilni materiali Binders. Sealing materials
93.080.20 Materiali za gradnjo cest Road construction materials
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN 13880-7
EUROPEAN STANDARD
NORME EUROPÉENNE
April 2019
EUROPÄISCHE NORM
ICS 93.080.20 Supersedes EN 13880-7:2003
English Version
Hot applied joint sealants - Part 7: Function testing of joint
sealants
Produits de scellement de joints appliqués à chaud - Heiß verarbeitbare Fugenmassen - Teil 7:
Partie 7 : Test fonctionnel sur produits de scellement Funktionsprüfung von Fugenmassen
de joints
This European Standard was approved by CEN on 25 February 2019.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13880-7:2019 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Principle . 5
5 Apparatus . 6
6 Preparation and conditioning of test specimens . 6
7 Test procedure . 8
8 Calculation and expression of results . 9
8.1 Maximum tension. 9
8.2 Failures . 10
9 Test report . 10
European foreword
This document (EN 13880-7:2019) has been prepared by Technical Committee CEN/TC 227 “Road
materials”, the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by October 2019, and conflicting national standards shall
be withdrawn at the latest by October 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 13880-7:2003.
This European Standard is one of a series of standards as listed below:
— EN 13880-1, Hot applied joint sealants — Part 1: Test method for the determination of density at
25 °C
— EN 13880-2, Hot applied joint sealants — Part 2: Test method for the determination of cone
penetration at 25°C
— EN 13880-3, Hot applied joint sealants — Part 3: Test method for the determination of penetration
and recovery (resilience)
— EN 13880-4, Hot applied joint sealants — Part 4: Test method for the determination of heat
resistance — Change in penetration value
— EN 13880-5, Hot applied joint sealants — Part 5: Test method for the determination of flow resistance
— EN 13880-6, Hot applied joint sealants — Part 6: Method for the preparation of samples for testing
— EN 13880-7, Hot applied joint sealants — Part 7: Function testing of joint sealants
— EN 13880-8, Hot applied joint sealants — Part 8: Test method for the determination of the change in
weight of fuel resistance joint sealants after fuel immersion
— EN 13880-9, Hot applied joint sealants — Part 9: Test method for the determination of compatibility
with asphalt pavements
— EN 13880-10, Hot applied joint sealants — Part 10: Test method for the determination of adhesion
and cohesion following continuous extension and compression
— EN 13880-11, Hot applied joint sealants — Part 11: Test method for the preparation of asphalt test
blocks used in the function test and for the determination of compatibility with asphalt pavements
— EN 13880-12, Hot applied joint sealants — Part 12: Test method for the manufacture of concrete test
blocks for bond testing (recipe methods)
— EN 13880-13, Hot applied joint sealants — Part 13: Test method for the determination of the
discontinuous extension (adherence test)
The following significant changes have been introduced in this edition:
— Accuracy requirements of apparatus have been added.
— Measurement device to measure depth of failures has been added.
— The conditioning procedure has been removed.
— Procedure for sealant type N2 and F2 has been added.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
1 Scope
This document describes a function
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.