Dentistry - Root canal instruments - Part 4: Auxiliary instruments (ISO 3630-4:2009)

ISO 3630-4:2009 specifies requirements and test methods for hand-held or mechanically operated instruments for performing root canal procedures not cited in ISO 3630-1, 3630-2, 3630-3 or 3630-5.
ISO 3630-4:2009 specifies requirements for size, product designation, safety considerations, instructions and labelling.

Zahnheilkunde - Wurzelkanalinstrumente - Teil 4: Hilfsinstrumente (ISO 3630-4:2009)

Dieser Teil von ISO 3630 legt Anforderungen und Prüfverfahren für handgeführte oder mechanisch betätigte
Wurzelkanalinstrumente fest, die für Wurzelkanalverfahren verwendet werden, die nicht in ISO 3630-1,
ISO 3630-2, ISO 3630-3 oder ISO 3630-5 aufgeführt sind.
Dieser Teil von ISO 3630 beschreibt Anforderungen an Größe, Produktbezeichnung, Sicherheitsüberlegungen
sowie Gebrauchsanweisung und Kennzeichnung.

Art dentaire - Instruments pour canaux radiculaires - Partie 4: Instruments auxiliaires (ISO 3630-4:2009)

L'ISO 3630-4:2009 spécifie les exigences et les méthodes d'essai relatives aux instruments à main ou mécaniques servant aux obturations canalaires, non mentionnés dans l'ISO 3630‑1, l'ISO 3630‑2, l'ISO 3630-3 ou l'ISO 3630-5.
L'ISO 3630-4:2009 spécifie les exigences concernant les dimensions, la désignation du produit, les précautions de sécurité, les instructions ainsi que l'étiquetage.

Zobozdravstvo - Instrumenti za zobni kanal - 4. del: Pomožni instrumenti (ISO 3630-4:2009)

General Information

Status
Published
Publication Date
30-Jun-2009
Technical Committee
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Due Date
01-Jul-2009
Completion Date
01-Jul-2009

RELATIONS

Buy Standard

Standard
EN ISO 3630-4:2009
English language
18 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (sample)

SLOVENSKI STANDARD
SIST EN ISO 3630-4:2009
01-oktober-2009

Zobozdravstvo - Instrumenti za zobni kanal - 4. del: Pomožni instrumenti (ISO 3630

-4:2009)

Dentistry - Root canal instruments - Part 4: Auxiliary instruments (ISO 3630-4:2009)

Zahnheilkunde - Wurzelkanalinstrumente - Teil 4: Hilfsinstrumente (ISO 3630-4:2009)

Art dentaire - Instruments pour canaux radiculaires - Partie 4: Instruments auxiliaires

(ISO 3630-4:2009)
Ta slovenski standard je istoveten z: EN ISO 3630-4:2009
ICS:
11.060.25 =RERWHKQLþQLLQVWUXPHQWL Dental instruments
SIST EN ISO 3630-4:2009 en

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 3630-4:2009
---------------------- Page: 2 ----------------------
SIST EN ISO 3630-4:2009
EUROPEAN STANDARD
EN ISO 3630-4
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2009
ICS 11.060.20
English Version
Dentistry - Root canal instruments - Part 4: Auxiliary instruments
(ISO 3630-4:2009)

Art dentaire - Instruments pour canaux radiculaires - Partie Zahnheilkunde - Wurzelkanalinstrumente - Teil 4:

4: Instruments auxiliaires (ISO 3630-4:2009) Hilfsinstrumente (ISO 3630-4:2009)
This European Standard was approved by CEN on 20 June 2009.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European

Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national

standards may be obtained on application to the CEN Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation

under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the

official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,

France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,

Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels

© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 3630-4:2009: E

worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 3630-4:2009
EN ISO 3630-4:2009 (E)
Contents Page

Foreword ..............................................................................................................................................................3

---------------------- Page: 4 ----------------------
SIST EN ISO 3630-4:2009
EN ISO 3630-4:2009 (E)
Foreword

This document (EN ISO 3630-4:2009) has been prepared by Technical Committee ISO/TC 106 "Dentistry" in

collaboration with Technical Committee CEN/TC 55 “Dentistry” the secretariat of which is held by DIN.

This European Standard shall be given the status of a national standard, either by publication of an identical

text or by endorsement, at the latest by January 2010, and conflicting national standards shall be withdrawn at

the latest by January 2010.

Attention is drawn to the possibility that some of the elements of this document may be the subject of patent

rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following

countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech

Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,

Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,

Sweden, Switzerland and the United Kingdom.
Endorsement notice

The text of ISO 3630-4:2009 has been approved by CEN as a EN ISO 3630-4:2009 without any modification.

---------------------- Page: 5 ----------------------
SIST EN ISO 3630-4:2009
---------------------- Page: 6 ----------------------
SIST EN ISO 3630-4:2009
INTERNATIONAL ISO
STANDARD 3630-4
First edition
2009-07-01
Dentistry — Root canal instruments —
Part 4:
Auxiliary instruments
Art dentaire — Instruments pour canaux radiculaires —
Partie 4: Instruments auxiliaires
Reference number
ISO 3630-4:2009(E)
ISO 2009
---------------------- Page: 7 ----------------------
SIST EN ISO 3630-4:2009
ISO 3630-4:2009(E)
PDF disclaimer

This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but

shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In

downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat

accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.

Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation

parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In

the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

COPYRIGHT PROTECTED DOCUMENT
© ISO 2009

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,

electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or

ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2009 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 3630-4:2009
ISO 3630-4:2009(E)
Contents Page

Foreword............................................................................................................................................................ iv

1 Scope ..................................................................................................................................................... 1

2 Normative references ........................................................................................................................... 1

3 Terms, definitions and symbols.......................................................................................................... 1

3.1 Terms and definitions........................................................................................................................... 1

3.2 Symbols ................................................................................................................................................. 2

4 Classification......................................................................................................................................... 2

5 Requirements ........................................................................................................................................ 3

5.1 Material .................................................................................................................................................. 3

5.2 Dimensions............................................................................................................................................ 3

5.3 Colour designation and size marking with rings............................................................................... 6

5.4 Mechanical requirements..................................................................................................................... 7

5.5 Resistance to corrosion....................................................................................................................... 9

5.6 Heat effects of sterilization .................................................................................................................. 9

6 Sampling................................................................................................................................................ 9

7 Testing ................................................................................................................................................... 9

7.1 General................................................................................................................................................... 9

7.2 Dimensions............................................................................................................................................ 9

8 Designation, marking and identification .......................................................................................... 10

9 Packaging ............................................................................................................................................ 10

10 Labelling .............................................................................................................................................. 10

Bibliography ..................................................................................................................................................... 11

© ISO 2009 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 3630-4:2009
ISO 3630-4:2009(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies

(ISO member bodies). The work of preparing International Standards is normally carried out through ISO

technical committees. Each member body interested in a subject for which a technical committee has been

established has the right to be represented on that committee. International organizations, governmental and

non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the

International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.

International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.

The main task of technical committees is to prepare International Standards. Draft International Standards

adopted by the technical committees are circulated to the member bodies for voting. Publication as an

International Standard requires approval by at least 75 % of the member bodies casting a vote.

Attention is drawn to the possibility that some of the elements of this document may be the subject of patent

rights. ISO shall not be held responsible for identifying any or all such patent rights.

ISO 3630-4 was prepared by Technical Committee ISO/TC 106, Dentistry, Subcommittee SC 4, Dental

instruments.

ISO 3630 consists of the following parts, under the general title Dentistry — Root canal instruments:

⎯ Part 1: General requirements and test methods
⎯ Part 2: Enlargers
⎯ Part 3: Condensers, pluggers and spreaders
⎯ Part 4: Auxiliary instruments
The following part is under preparation:
⎯ Part 5: Shaping and cleaning instruments
iv © ISO 2009 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 3630-4:2009
INTERNATIONAL STANDARD ISO 3630-4:2009(E)
Dentistry — Root canal instruments —
Part 4:
Auxiliary instruments
1 Scope

This part of ISO 3630 specifies requirements and test methods for hand-held or mechanically operated

instruments for performing root canal procedures not cited in ISO 3630-1, 3630-2, 3630-3 or 3630-5.

This part of ISO 3630 specifies requirements for size, product designation, safety considerations, instructions

and labelling.
2 Normative references

The following referenced documents are indispensable for the application of this document. For dated

references, only the edition cited applies. For undated references, the latest edition of the referenced

document (including any amendments) applies.
ISO 1797-1, Dental rotary instruments — Shanks — Part 1: Shanks made of metals
ISO 1797-2, Dental rotary instruments — Shanks — Part 2: Shanks made of plastics
ISO 1942, Dentistry — Vocabulary

ISO 3630-1:2008, Dentistry — Root-canal instruments — Part 1: General requirements and test methods

ISO 3630-2:2000, Dental root-canal instruments — Part 2: Enlargers
3 Terms, definitions and symbols
3.1 Terms and definitions

For the purposes of this document, the terms and definitions given in ISO 1942, ISO 3630-1 and the following

apply.
3.1.1
barbed broach
root-canal instrument with barbs designed for removing the pulp tissue
3.1.2
rasp
root-canal instrument in which
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.