EN ISO 21952:2007
(Main)Welding consumables - Wire electrodes, wires, rods and deposits for gas-shielded arc welding of creep-resisting steel - Classification (ISO 21952:2007)
Welding consumables - Wire electrodes, wires, rods and deposits for gas-shielded arc welding of creep-resisting steel - Classification (ISO 21952:2007)
ISO 21952:2007 specifies requirements for classification of wire electrodes, wires and rods for gas-shielded metal arc welding and tungsten inert-gas welding of creep-resisting steels, and for their deposits in the as-welded or post-weld heat-treated condition. One wire electrode can be tested and classified with different shielding gases.
ISO 21952:2007 is a combined specification providing for classification utilizing a system based upon the chemical composition of wire electrodes, wires and rods with requirements for yield strength and average impact energy of 47 J of all-weld metal, or utilizing a system based upon the tensile strength of the all-weld metal deposits and the chemical composition of wire electrodes, wires and rods.
Schweißzusätze - Drahtelektroden, Drähte, Stäbe und Schweißgut zum Schutzgasschweißen von warmfesten Stählen - Einteilung (ISO 21952:2007)
Diese Internationale Norm legt Anforderungen zur Einteilung von Drahtelektroden, Drähten und Stäben für das Schutzgasschweißen und Wolfram-Inertgasschweißen von warmfesten Stählen fest sowie für ihr Schweißgut im Schweißzustand oder nach einer Wärmebehandlung. Eine Drahtelektrode kann mit unterschiedlichen Schutzgasen geprüft und entsprechend eingeteilt werden.
Diese Internationale Norm benutzt zur Einteilung ein kombiniertes System, das auf der Einteilung nach der chemischen Zusammensetzung der Drahtelektroden, Drähte und Stäbe mit Anforderungen an Streckgrenze und an die durchschnittliche Kerbschlagarbeit des reinen Schweißgutes von 47 J beruht oder auf der Zugfestigkeit des reinen Schweißgutes und der chemischen Zusammensetzung der Drahtelektroden, Drähte und Stäbe.
1) Abschnitte, Unterabschnitte und Tabellen mit dem zusätzlichen Buchstaben „A“ sind nur für Drahtelektroden, Drähte, Stäbe und Schweißgut anwendbar, die nach dem System eingeteilt sind, das auf der chemischen Zusammensetzung mit Anforderungen an Streckgrenze und an die durchschnittliche Kerbschlagarbeit des reinen Schweißgutes von 47 J nach dieser Internationalen Norm beruht.
2) Abschnitte, Unterabschnitte und Tabellen mit dem zusätzlichen Buchstaben „B“ sind nur für Drahtelektroden, Drähte, Stäbe und Schweißgut anwendbar, die nach dem System eingeteilt sind, das auf der Zugfestigkeit des reinen Schweißgutes und der chemischen Zusammensetzung der Drahtelektroden, Drähte und Stäbe nach dieser Internationalen Norm beruht.
3) Abschnitte, Unterabschnitte und Tabellen ohne zusätzlichen Buchstaben „A“ oder „B“ sind für alle nach dieser Internationalen Norm eingeteilten Drahtelektroden, Drähte, Stäbe und Schweißgut anwendbar.
Produits consommables pour le soudage - Fils-électrodes, fils, baguettes et dépôts pour le soudage à l'arc sous protection gazeuse des aciers résistant au fluage - Classification (ISO 21952:2007)
L'ISO 21952:2007 spécifie les exigences relatives à la classification des fils-électrodes, des fils et des baguettes pour le soudage à l'arc avec électrode fusible sous protection gazeuse et pour le soudage TIG des aciers résistant au fluage, ainsi que pour les dépôts à l'état brut de soudage ou après traitement thermique après soudage. Un fil-électrode peut être soumis aux essais et classifié en utilisant différents gaz de protection.
L'ISO 21952:2007 propose une spécification mixte permettant une classification utilisant soit un système basé sur la composition chimique des fils-électrodes, des fils et des baguettes, avec des exigences sur la limite d'élasticité et l'énergie de rupture moyenne de 47 J pour le métal fondu hors dilution, soit un système basé sur la résistance à la traction des dépôts de métal fondu hors dilution et la composition chimique des fils-électrodes, des fils et des baguettes.
Dodajni materiali za varjenje - Žice in palice za obločno varjenje v zaščitnih plinih jekel, odpornih proti lezenju - Razvrstitev (ISO 21952:2007)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-april-2008
'RGDMQLPDWHULDOL]DYDUMHQMHäLFHLQSDOLFH]DREORþQRYDUMHQMHY]DãþLWQLKSOLQLK
MHNHORGSRUQLKSURWLOH]HQMX5D]YUVWLWHY ,62
Welding consumables - Wire electrodes, wires, rods and deposits for gas-shielded arc
welding of creep-resisting steel - Classification (ISO 21952:2007)
Schweißzusätze - Drahtelektroden, Drähte, Stäbe und Schweißgut zum
Schutzgasschweißen von warmfesten Stählen - Einteilung (ISO 21952:2007)
Produits consommables pour le soudage - Fils-électrodes, fils, baguettes et dépôts pour
le soudage a l'arc sous gaz de protection des aciers résistant au fluage - Classification
(ISO 21952:2007)
Ta slovenski standard je istoveten z: EN ISO 21952:2007
ICS:
25.160.20
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 21952
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2007
ICS 25.160.20 Supersedes EN 12070:1999
English Version
Welding consumables - Wire electrodes, wires, rods and
deposits for gas-shielded arc welding of creep-resisting steel -
Classification (ISO 21952:2007)
Produits consommables pour le soudage - Fils-électrodes, Schweißzusätze - Drahtelektroden, Drähte, Stäbe und
fils, baguettes et dépôts pour le soudage à l'arc sous Schweißgut zum Schutzgasschweißen von warmfesten
protection gazeuse des aciers résistant au fluage - Stählen - Einteilung (ISO 21952:2007)
Classification (ISO 21952:2007)
This European Standard was approved by CEN on 17 October 2007.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2007 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 21952:2007: E
worldwide for CEN national Members.
Contents Page
Foreword.3
Foreword
This document (EN ISO 21952:2007) has been prepared by Technical Committee ISO/TC 44 "Welding and
allied processes" in collaboration with Technical Committee CEN/TC 121 “Welding” the secretariat of which is
held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by May 2008, and conflicting national standards shall be withdrawn at the
latest by May 2008.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 12070:1999.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 21952:2007 has been approved by CEN as a EN ISO 21952:2007 without any modification.
INTERNATIONAL ISO
STANDARD 21952
First edition
2007-11-15
Welding consumables — Wire electrodes,
wires, rods and deposits for gas-shielded
arc welding of creep-resisting steels —
Classification
Produits consommables pour le soudage — Fils-électrodes, fils,
baguettes et dépôts pour le soudage à l'arc sous protection gazeuse
des aciers résistant au fluage — Classification
Reference number
ISO 21952:2007(E)
©
ISO 2007
ISO 21952:2007(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2007 – All rights reserved
ISO 21952:2007(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Classification. 2
4 Symbols and requirements. 2
4.1 Symbol for the product/process . 2
4.2 Symbol for the chemical composition of wire electrodes, wires and rods . 2
4.3 Symbol for the mechanical properties of all-weld metal . 3
4.4 Symbol for shielding gas . 3
4.5 Rounding-off procedure. 3
5 Mechanical tests . 10
5.1 Preheating and interpass temperatures.10
5.2 Welding conditions and pass sequence . 10
6 Chemical analysis. 11
7 Retests . 11
8 Technical delivery conditions . 11
9 Examples of designations . 11
Bibliography . 14
ISO 21952:2007(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 21952 was prepared by Technical Committee ISO/TC 44, Welding and allied processes, Subcommittee
SC 3, Welding consumables.
Requests for official interpretations of any aspect of this International Standard should be directed to the
Secretariat of ISO/TC 44/SC 3 via your national standards body. A listing of these bodies can be found at
http://www.iso.org.
iv © ISO 2007 – All rights reserved
ISO 21952:2007(E)
Introduction
This International Standard provides a classification in order to designate wire electrodes, wires and rods in
terms of their chemical composition and, where required, in terms of the yield strength, tensile strength and
elongation of the all-weld metal deposit. The ratio of yield to tensile strength of weld metal is generally higher
than that of parent metal. Users should note that matching weld metal yield strength to parent metal yield
strength will not necessarily ensure that the weld metal tensile strength matches that of the parent material.
Where the application requires matching tensile strength, therefore, selection of the consumable should be
made by reference to column 4 of Table 2.
It should be noted that the mechanical properties of all-weld metal test pieces used to classify the electrodes,
wires and rods will vary from those obtained in production joints because of differences in welding procedure
such as electrode size, width of weave, welding position and material composition.
This International Standard was prepared in collaboration with the International Institute of Welding. It
recognizes that there are two somewhat different approaches in the global market to classifying a given wire
electrode, wire, rod or deposit, and allows for either or both to be used to suit a particular market need.
Application of either type of classification designation (or of both where suitable) identifies a product as
classified in accordance with this International Standard. The classification in accordance with system A is
mainly based on EN 12070:1999. The classification in accordance with system B is mainly based upon
standards used around the Pacific Rim. Future revisions will aim to merge the two approaches into a single
classification system.
INTERNATIONAL STANDARD ISO 21952:2007(E)
Welding consumables — Wire electrodes, wires, rods and
deposits for gas-shielded arc welding of creep-resisting
steels — Classification
1 Scope
This International Standard specifies requirements for classification of wire electrodes, wires and rods for
gas-shielded metal arc welding and tungsten inert-gas welding of creep-resisting steels, and for their deposits
in the as-welded or post-weld heat-treated condition. One wire electrode can be tested and classified with
different shielding gases.
This International Standard is a combined specification providing for classification utilizing a system based
upon the chemical composition of wire electrodes, wires and rods with requirements for yield strength and
average impact energy of 47 J of all-weld metal, or utilizing a system based upon the tensile strength of the
all-weld metal deposits and the chemical composition of wire electrodes, wires and rods.
1) Clauses, subclauses and tables which carry the suffix letter “A” are applicable only to wire electrodes,
wires, rods and deposits classified in accordance with the system based upon the chemical
composition with requirements for yield strength and the average impact energy of 47 J of all-weld
metal deposits under this International Standard.
2) Clauses, subclauses and tables which carry the suffix letter “B” are applicable only to wire electrodes,
wires, rods and deposits classified in accordance with the system based upon the tensile strength of
all-weld metal deposits and the chemical composition of wire electrodes,
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.