EN 13611:2015/AC:2016
(Corrigendum)Safety and control devices for burners and appliances burning gaseous and/or liquid fuels - General requirements
Safety and control devices for burners and appliances burning gaseous and/or liquid fuels - General requirements
CCMC origin - eXtyles accidentally cleaned the Table cells so thoroughly that the crosses were displaced
Sicherheits- und Regeleinrichtungen für Brenner und Brennstoffgeräte für gasförmige und/oder flüssige Brennstoffe - Allgemeine Anforderungen
Équipements auxiliaires pour brûleurs et appareils utilisant des combustibles gazeux ou liquides - Exigences générales
Varnostne in nadzorne naprave za gorilnike in aparate na plin in/ali tekoča goriva - Splošne zahteve - Popravek AC
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Sicherheits- und Regeleinrichtungen für Brenner und Brennstoffgeräte für gasförmige und/oder flüssige Brennstoffe - Allgemeine AnforderungenÉquipements auxiliaires pour brûleurs et appareils utilisant des combustibles gazeux ou liquides - Exigences généralesSafety and control devices for burners and appliances burning gaseous and/or liquid fuels - General requirements27.060.20Plinski gorilnikiGas fuel burners23.060.40Pressure regulatorsICS:Ta slovenski standard je istoveten z:EN 13611:2015/AC:2016SIST EN 13611:2015/AC:2016en,fr,de01-april-2016SIST EN 13611:2015/AC:2016SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13611:2015/AC
February
t r s x
Février
t r s x
Februar
t r s x ICS
t uä r x rä v r English version Version Française Deutsche Fassung
Safety and control devices for burners and appliances burning liquid fuels æ General requirements
Équipements auxiliaires pour brûleurs et appareils utilisant des combustibles gazeux ou liquides æ Exigences générales
Sicherheitsæ und Regeleinrichtungen für Brenner und Brennstoffgeräte für gasförmige Anforderungen This corrigendum becomes effective on
s r February
t r s x for incorporation in the three official language versions of the ENä
Ce corrigendum prendra effet le
s r février
t r s x pour incorporation dans les trois versions linguistiques officielles de la ENä
Die Berichtigung tritt am
s rä Februar
t r s x zur Einarbeitung in die drei offiziellen Sprachfassungen der EN in Kraftä
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
t r s x CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Tous droits d 5exploitation sous quelque forme et de quelque manière que ce soit réservés dans le monde entier aux membres nationaux du CENä Alle Rechte der Verwertungá gleich in welcher Form und in welchem Verfahrená sind weltweit den nationalen Mitgliedern von CEN vorbehaltenä SIST EN 13611:2015/AC:2016
Replace Table E.1 with the following one: " Table E.1 — Electrical/electronic component faults modes Component type Short Opena Remarks Fixed resistors: Thin film (wound filament) Thick film (flat) Wire-wound (single layer) All other types
x
x x x x
Includes SMD type Includes SMD type Variable resistors (e.g. potentiometer/trimmer): Wire-wound (single layer) All other types
xb
x x
Capacitors: X1 and Y types according to EN 60384–14:2013 Metallized film according to EN 60384–16:2005 All other types
x
x x x
Inductors: Wire-wound (single layer) All other types
x
x x
Diodes: All types
x
x
Transistors: All types (e.g. Bipolar: LF; RF; microwave; FET; Thyristor; Diac; Triac; Uni junction)
xb
x
c Hybrid circuit d d
Integrated circuits xe x For IC outputs notec applies Photocouplers xf x
Relays:
Coils x x If the relay complies with EN 61810–1:2008 the failure mode short circuit need not be considered. Contacts xg h o x
Reed-relays x x Contacts only Electromechanical lock-out elements:
Coils x x
Contacts xp x
x
x
x
Crystals x x i Switches x x j Connections (jumper wire)
x k Cable, wiring and connectors
x
Printed circuit board conductors xm xl
Temperature sensors: All types (e.g. NTC, PTC, PT 100 and thermocouples)
xn
xn
a Only opening of one pin at a time. b Short circuit each pin in turn with every other pin; only two pins at a time. c For discrete or integrated thyristor type devices such as triacs and SCRs, fault conditions shall include short
circuit of
any terminals with the third terminal open circuited. The effect of any full wave type component,
such as a triac going into a half wave condition, either controlled or uncontrolled (thyristor or diode,
respectively) shall be considered. d Failure modes for individual components of the hybrid circuit are applicable as described for the individual
components
in this table. e The short circuit of any two adjacent terminals and the short circuiting of: a) each terminal to the IC-supply, when applicable at the IC, b) each terminal to the IC-ground, when applicable at the IC. The number of tests implied for integrated circuits can normally make it impracticable to apply all the relevant fault conditions or to assess the likely hazards from an appraisal of the circuit diagram of the integrated circuit. It is therefore permissible first to analyse in detail all the possible mechanical, thermal and electrical faults which can develop either in the control itself or its output, due to the malfunction of the electronic devices or other circuit components, separately or in any combination. An analysis (e.g. a fault tree analysis) shall be conducted to include the results of multiple steady-state conditions to outputs and programmed bi-directional terminals for the purpose of identifying additional fault conditions for consid
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.