EN 12629-7:2004/FprA1
(Amendment)Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 7: Stationary and mobile equipment for long line manufacture of prestressed products
Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 7: Stationary and mobile equipment for long line manufacture of prestressed products
Maschinen für die Herstellung von Bauprodukten aus Beton und Kalksandsteinmassen - Sicherheit - Teil 7: Stationäre und fahrbare Einrichtungen für die Herstellung von Spannbetonelementen
Machines pour la fabrication de produits de construction en béton et silico-calcaire - Sécurité - Partie 7: Equipements fixes et mobiles pour la fabrication sur bancs de produits en béton précontraint
Stroji za izdelavo gradbenih proizvodov iz betona in apnenega peščenca - Varnost - 7. del: Nepremična in premična oprema za izdelavo elementov iz prednapetega betona
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-april-2010
6WURML]DL]GHODYRJUDGEHQLKSURL]YRGRYL]EHWRQDLQDSQHQHJDSHãþHQFD9DUQRVW
GHO 1HSUHPLþQDLQSUHPLþQDRSUHPD]DL]GHODYRHOHPHQWRYL]SUHGQDSHWHJD
EHWRQD
Machines for the manufacture of constructional products from concrete and calcium-
silicate - Safety - Part 7: Stationary and mobile equipment for long line manufacture of
prestressed products
Maschinen für die Herstellung von Bauprodukten aus Beton und Kalksandsteinmassen -
Sicherheit - Teil 7: Stationäre und fahrbare Einrichtungen für die Herstellung von
Spannbetonelementen
Machines pour la fabrication de produits de construction en béton et silico-calcaire -
Sécurité - Partie 7: Equipements fixes et mobiles pour la fabrication sur bancs de
produits en béton précontraint
Ta slovenski standard je istoveten z: EN 12629-7:2004/FprA1
ICS:
91.220 Gradbena oprema Construction equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
FINAL DRAFT
EN 12629-7:2004
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
February 2010
ICS 91.220
English Version
Machines for the manufacture of constructional products from
concrete and calcium-silicate - Safety - Part 7: Stationary and
mobile equipment for long line manufacture of prestressed
products
Machines pour la fabrication de produits de construction en Maschinen für die Herstellung von Bauprodukten aus Beton
béton et silico-calcaire - Sécurité - Partie 7: Equipements und Kalksandsteinmassen - Sicherheit - Teil 7: Stationäre
fixes et mobiles pour la fabrication sur bancs de produits en und fahrbare Einrichtungen für die Herstellung von
béton précontraint Spannbetonelementen
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 151.
This draft amendment A1, if approved, will modify the European Standard EN 12629-7:2004. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 12629-7:2004/FprA1:2010: E
worldwide for CEN national Members.
Contents Page
Foreword . 3
1 Modifications to the Foreword . 4
2 Modifications to the Introduction . 5
3 Modifications to Clause 1 (Scope) . 5
4 Modifications to Clause 2 (Normative references) . 6
5 Modifications to Clause 3 (Terms and definitions) . 7
6 Modifications to Clause 4 (List of significant hazards) . 7
7 Modifications to Clause 5 (Safety requirements and/or measures) . 7
8 Modifications to Clause 6 (Verification of the requirements and/or measures) . 40
9 Modifications to Clause 7 (Information for use – Instruction handbook) . 40
10 Modifications to Clause 8 (Marking) . 40
11 Modifications to Annex H (Trilingual list of terms relative to pre-stressing manufacturing
products and equipment) . 40
12 Modification to Annex ZA . 42
13 Addition of a new Annex ZB, Relationship between this European Standard and the Essential
Requirements of EU Directive 2006/42/EC . 43
Foreword
This document (EN 12629-7:2004/FprA1:2010) has been prepared by Technical Committee CEN/TC 151
“Construction equipment and building material machines - Safety”, the secretariat of which is held by DIN.
This document is currently submitted to the Unique Acceptance Procedure.
This document has been prepared under a mandate given to CEN by the European Commission and the European
Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are integral parts of this
document.
1 Modifications to the Foreword
th
Replace the 4 paragraph with the following:
"For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are integral parts of this
document."
th
Delete the 5 paragraph.
th
Replace the 6 paragraph with the following:
"The series "Machines for the manufacture of constructional products from concrete and calcium – silicate – Safety"
consists of following parts:
Part 1: Common requirements
Part 2: Block making machines
Part 3: Slide and turntable machines
Part 4: Concrete rooftile making machines
Part 5.1: Concrete pipe machines manufacturing in the vertical axis.
Part 5.2: Concrete pipe machines manufacturing in the horizontal axis
Part 5.3: Pipe prestressing machines
Part 5.4: Concrete pipe coating machines
Part 6: Stationary and mobile equipment for the manufacture of precast reinforced products
Part 7: Stationary and mobile equipment for the benched manufacture of prestressed products
Part 8: Machines and equipment for the manufacture of constructional products from calcium silicate (and
concrete)."
th th
Delete the 7 and 8 paragraphs.
2 Modifications to the Introduction
First paragraph, update the reference as follows:
Replace "EN 1070:1998" with "EN ISO 12100".
Fourth paragraph, update the reference as follows:
Replace "EN 12629-1" with "EN 12629-1:2000+A1".
3 Modifications to Clause 1 (Scope)
Sub-clause 1.1, replace the existing text with the following:
1.1 "This part of EN 12629, taken together with EN 12629-1:2000+A1, applies to stationary and mobile equipment
for the benched manufacture of prestressed products. The manufacturing bed is a machine with which other
associated machines work simultaneously. Moreover, these machines are generally used on beds installed in
parallel.
EN 12629-1:2000+A1 specifies general requirements applicable to machines for the manufacture of constructional
products from concrete and calcium–silicate.
This document specifies the additional requirements to and/or the deviations from EN 12629-1:2000+A1 specific to
the machines it covers."
Sub-clause 1.2, add the following text at the end:
"The handling of the cut wires and their placement on beds is not covered by the present standard."
Sub-clause 1.3, replace the existing text with the following:
1.3 "This European Standard deals with all significant hazards pertinent to these machines, when they are used as
intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4).
This European Standard specifies the appropriate technical measures to eliminate or reduce risks arising from the
significant hazards."
Sub-clause 1.4, update the reference as follows:
Replace "EN 12629-1:2000" with "EN 12629-1:2000+A1:2010".
Delete sub-clause 1.5.
Renumber sub-clause 1.6 into !1.5".
4 Modifications to Clause 2 (Normative references)
Replace the existing text with the following:
"The following referenced documents are indispensable for the application of this document. For dated references,
only the edition cited applies. For undated references, the latest edition of the referenced document (including any
amendments) applies.
EN 349:1993, Safety of machinery — Minimum gaps to avoid crushing of parts of the human body
EN 457, Safety of machinery — Auditory danger signals — General requirements, design and testing (ISO
7731:1986, modified)
EN 842, Safety of machinery —Visual danger signals — General requirements, design and testing
EN 953:1997, Safety of machinery — Guards — General requirements for the design and construction of fixed and
movable guards
EN 954-1:1996, Safety of machinery — Safety-related parts of control systems — Part 1: General principles for
design
EN 982, Safety of machinery — Safety requirements for fluid power systems and their components — Hydraulics
EN 1050:1996, Safety of machinery — Principles for risk assessment
EN 1088, Safety of machinery — Interlocking devices associated with guards — Principles for design and selection
EN 1093 (all parts), Safety of machinery — Evaluation of the emission of airborne hazardous substances
EN 1760-2, Safety of machinery — Pressure sensitive protective devices — Part 2: General principles for the
design and testing of pressure sensitive edges and pressure sensitive bars
EN 13862:2001, Floor cutting-off machines — Safety
EN 12629-1:2000+A1:2010, Machines for the manufacture of constructional products from concrete and calcium-
silicate — Safety — Part 1: Common requirements
EN 60204-1, Safety of machinery - Electrical equipment of machines — Part 1: General requirements (IEC 60204-
1:2005, modified)
EN 60529, Degrees of protection provided by enclosures (IP code) (IEC 60529:1989)
EN ISO 3457, Earth-moving machinery — Guards — Definitions and requirements (ISO 3457:2003)
EN ISO 7731:2008, Ergonomics — Danger signals for public and work areas — Auditory danger signals (ISO
7731:2003)
EN ISO 13857:2008, Safety of machinery — Safety distances to prevent hazard zones being reached by upper and
lower limbs (ISO 13857:2008)
EN ISO 12100-1:2003, Safety of machinery — Basic concepts, general principles for design — Part 1: Basic
terminology, methodology (ISO 12100-1:2003)
EN ISO 12100-2:2003, Safety of machinery — Basic concepts, general principles for design — Part 2: Technical
principles (ISO 12100-2:2003)
EN ISO 13732-1:2008, Ergonomics of the thermal environment — Methods for the assessment of human
responses to contact with surfaces — Part 1: Hot surfaces (ISO 13732-1:2006)
EN ISO 14122-1:2001, Safety of machinery — Permanent means of access to machinery — Part 1: Choice of fixed
means of access between two levels (ISO 14122-1:2001)
EN ISO 14122-2:2001, Safety of machinery — Permanent means of access to machinery — Part 2: Working
platforms and gangways (ISO 14122-2:2001)
EN ISO 14122-3:2001, Safety of machinery — Permanent means of access to machinery — Part 3: Stairways,
stepladders and guard-rails (ISO 14122-3:2001)
EN ISO 14122-4:2004, Safety of machinery — Permanent means of access to machinery — Part 4: Fixed ladders
(ISO 14122-4:2004)"
5 Modifications to Clause 3 (Terms and definitions)
First and second paragraphs, replace the existing text with the following:
"For the purposes of this document, the terms and definitions given in EN ISO 12100-1:2003, EN 12629-
1:2000+A1:2010 and the following apply."
6 Modifications to Clause 4 (List of significant hazards)
Delete the second paragraph.
Fourth paragraph, update the references as follows:
Replace "EN 12629-1:2000" with "EN 12629-1:2000+A1:2010".
7 Modifications to Clause 5 (Safety requirements and/or measures)
Replace the headline with the following:
"Safety requirements and/or protective measures"
First paragraph:
Add a new sub-clause "5.1 Introduction" and replace the text with the following:
"Machinery shall comply with the safety requirements and/or protective measures of this clause and, unless
otherwise specified in this standard, with the relevant requirements of EN 12629-1:2000+A1. In addition, the
machine shall be designed according to the principles of EN ISO 12100 for hazards relevant but not significant,
which are not dealt with by this document.
NOTE For hazards which are to be reduced by the application of an A or B-level standard such as EN 349, EN 547, EN
614-1, EN 894, EN 953, EN 1088, EN ISO 7731, EN ISO 13850, EN ISO 13857, EN ISO 14122-1, and for hydraulic, pneumatic
or other machinery dealt with in standards for common uses, the manufacturer should carry out a risk assessment to establish
the requirements of the A or B-level or other standard which are to be applied. This specific risk assessment should be part of
the general risk assessment of the machine.
Where it is known that the installation site already contains elements t
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.