EN 792-10:2000+A1:2008
(Main)Hand-held non-electric power tools - Safety requirements - Part 10: Compression power tools
Hand-held non-electric power tools - Safety requirements - Part 10: Compression power tools
The standard EN 792 applies to hand-held non-electric power tools driven by rotary or linear motors, powered by compressed air, hydraulic fluid and intended to be used by one operator and supported by:
- the operator's hand or hands
- a suspension, e.g. a balancer.
This part, EN 792-10, applies to hand-held non electric compression power tools with yoke, e.g. for squeeze riveting, punching, shaping, pressing and cutting of metal, plastics or other materials.
This part lists the significant hazards caused by such power tools and specifies safety requirements valid for different aspects of safety during their foreseeable lifetime.
Power tools, all of them with a yoke, covered by this part of the standard:
- crimping tools,
- collar splitters,
- power tools for metal forming (edge formers, folding tools, swagers),
- nut splitter heads,
- presses,
- punches,
- squeeze riveters,
- cutting power tools with parallel knives.
Special requirements and modifications on a hand-held power tool for the purpose of mounting it in a fixture are not covered by this part.
NOTE At the date of publication no compression power tools driven by internal combustion engines are known.
Handgehaltene nicht-elektrisch betriebene Maschinen - Sicherheitsanforderungen - Teil 10: Maschinen zum Pressen
Machines portatives à moteur non électrique - Prescriptions de sécurité - Partie 10: Machines portatives à compression
Neelektrična ročna orodja - Varnostne zahteve - 10. del: Električna orodja za stiskanje
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 792-10:2000+A1:2008
01-november-2008
1HHOHNWULþQDURþQDRURGMD9DUQRVWQH]DKWHYHGHO(OHNWULþQDRURGMD]D
VWLVNDQMH
Hand-held non-electric power tools - Safety requirements - Part 10: Compression power
tools
Handgehaltene nicht-elektrisch betriebene Maschinen - Sicherheitsanforderungen - Teil
10: Maschinen zum Pressen
Machines portatives à moteur non électrique - Prescriptions de sécurité - Partie 10:
Machines portatives à compression
Ta slovenski standard je istoveten z: EN 792-10:2000+A1:2008
ICS:
25.140.10 3QHYPDWLþQDRURGMD Pneumatic tools
SIST EN 792-10:2000+A1:2008 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 792-10:2000+A1:2008
---------------------- Page: 2 ----------------------
SIST EN 792-10:2000+A1:2008
EUROPEAN STANDARD
EN 792-10:2000+A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2008
ICS 25.140.10; 25.140.99 Supersedes EN 792-10:2000
English Version
Hand-held non-electric power tools - Safety requirements - Part
10: Compression power tools
Machines portatives à moteur non électrique - Prescriptions Handgehaltene nicht-elektrisch betriebene Maschinen -
de sécurité - Partie 10: Machines portatives à compression Sicherheitsanforderungen - Teil 10: Maschinen zum
Pressen
This European Standard was approved by CEN on 26 May 2000 and includes Amendment 1 approved by CEN on 26 July 2008.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 792-10:2000+A1:2008: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 792-10:2000+A1:2008
EN 792-10:2000+A1:2008 (E)
Contents Page
Foreword.3
Introduction .4
1 Scope .4
2 Normative references .5
3 Terms and definitions .6
3.1 General terms and definitions.6
3.2 Terms and definitions related to compression power tools .7
4 List of hazards.8
5 Safety requirements and measures.9
5.1 Mechanical safety .9
5.2 Thermal safety.9
5.3 Noise .9
5.4 Vibration .10
5.5 Materi
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.