EN ISO 1167-4:2007

Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 4: Preparation of assemblies (ISO 1167-4:2007)

ISO 1167-4:2007 specifies the procedure for the preparation of both end‑load‑bearing and non‑end‑load‑bearing assemblies, for the determination of their resistance to internal hydrostatic pressure according to ISO 1167-1.

Rohre, Formstücke und Bauteilkombinationen aus thermoplastischen Kunststoffen für den Transport von Flüssigkeiten - Bestimmung der Widerstandsfähigkeit gegen inneren Überdruck - Teil 4: Vorbereitung der Bauteilkombinationen (ISO 1167-4:2007)

Dieser Teil der ISO 1167 legt das Verfahren für die Vorbereitung sowohl von axial beanspruchten als auch von nicht axial beanspruchten Bauteilkombinationen für die Bestimmung der Widerstands¬fähigkeit gegen hydrostatischen Innendruck nach ISO 1167-1 fest.
ANMERKUNG      Die Bauteilkombinationen bestehen aus einer Auswahl von Rohren, Formstücken, Armaturen, Schweiß- oder Klebverbindungen.

Tubes, raccords et assemblages en matières thermoplastiques pour le transport des fluides - Détermination de la résistance à la pression interne - Partie 4: Préparation des assemblages (ISO 1167-4:2007)

L'ISO 1167-4:2007 spécifie le mode opératoire pour la préparation à la fois des assemblages avec effet de fond et des assemblages sans effet de fond, en vue de déterminer la résistance à la pression hydrostatique interne selon l'ISO 1167-1.

Plastomerne cevi, fitingi in spoji za transport tekočin - Določanje odpornosti proti notranjemu tlaku - 4. del: Priprava spojev (ISO 1167-4:2007)

General Information

• Status: Published
• Publication Date: 31-Oct-2007
• Withdrawal Date: 30-May-2008
• ICS: 23.040.20 - Plastics pipes
• ICS: 23.040.45 - Plastics fittings
• Technical Committee: CEN/TC 155 - Plastics piping systems and ducting systems
• Drafting Committee: CEN/TC 155 - Plastics piping systems and ducting systems
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 01-Nov-2007
• Completion Date: 01-Nov-2007
• Ref Project: SIST EN ISO 1167-4:2008 - Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 4: Preparation of assemblies (ISO 1167-4:2007)

Relations

• Replaces: EN 921:1994/AC:1995 - Plastics piping systems - Thermoplastics pipes - Determination of resistance to internal pressure at constant temperature
• Effective Date: 22-Dec-2008

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 1167-4:2008
01-junij-2008
1DGRPHãþD
SIST EN 921:1997
3ODVWRPHUQHFHYLILWLQJLLQVSRML]DWUDQVSRUWWHNRþLQ'RORþDQMHRGSRUQRVWLSURWL
QRWUDQMHPXWODNXGHO3ULSUDYDVSRMHY,62
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids -
Determination of the resistance to internal pressure - Part 4: Preparation of assemblies
(ISO 1167-4:2007)
Rohre, Formstücke und Bauteilkombinationen aus thermoplastischen Kunststoffen für
den Transport von Flüssigkeiten - Bestimmung der Widerstandsfähigkeit gegen inneren
Überdruck - Teil 4: Vorbereitung der Bauteilkombinationen (ISO 1167-4:2007)
Tubes, raccords et assemblages en matieres thermoplastiques pour le transport des
fluides - Détermination de la résistance a la pression interne - Partie 4: Préparation des
assemblages (ISO 1167-4:2007)
Ta slovenski standard je istoveten z: EN ISO 1167-4:2007
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
23.040.45 Fitingi iz polimernih Plastics fittings
materialov
SIST EN ISO 1167-4:2008 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

EUROPEAN STANDARD
EN ISO 1167-4
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2007
ICS 23.040.20; 23.040.45 Supersedes EN 921:1994
English Version
Thermoplastics pipes, fittings and assemblies for the
conveyance of fluids - Determination of the resistance to internal
pressure - Part 4: Preparation of assemblies (ISO 1167-4:2007)
Tubes, raccords et assemblages en matières Rohre, Formstücke und Bauteilkombinationen aus
thermoplastiques pour le transport des fluides - thermoplastischen Kunststoffen für den Transport von
Détermination de la résistance à la pression interne - Partie Flüssigkeiten - Bestimmung der Widerstandsfähigkeit
4: Préparation des assemblages (ISO 1167-4:2007) gegen inneren Überdruck - Teil 4: Vorbereitung der
Bauteilkombinationen (ISO 1167-4:2007)
This European Standard was approved by CEN on 2 October 2007.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2007 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 1167-4:2007: E
worldwide for CEN national Members.

---------------------- Page: 2 ----------------------

EN ISO 1167-4:2007 (E)
Contents Page
Foreword.3

2

---------------------- Page: 3 ----------------------

EN ISO 1167-4:2007 (E)
Foreword
This document (EN ISO 1167-4:2007) has been prepared by Technical Committee ISO/TC 138 "Plastics
pipes, fittings and valves for the transport of fluids" in collaboration with Technical Committee CEN/TC 155
“Plastics piping systems and ducting systems” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by May 2008, and conflicting national standards shall be withdrawn at the
latest by May 2008.
This document supersedes EN 921:1994.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 1167-4:2007 has been approved by CEN as a EN ISO 1167-4:2007 without any modification.

3

---------------------- Page: 4 ----------------------

INTERNATIONAL ISO
STANDARD
...