prEN 18007-2
(Main)Electromagnetic pulse welding - Part 2: Design of welded joints
Electromagnetic pulse welding - Part 2: Design of welded joints
This document specifies design requirements for electromagnetic pulse welds and provides design guidelines for electromagnetic pulse welding.
Schweißen und verwandte Verfahren - Elektromagnetisches Pulsschweißen - Teil 2: Ausführung der Schweißverbindungen
Dieses Dokument legt die Anforderungen an die Ausführung von elektromagnetischen Pulsschweißungen fest und enthält Richtlinien für die Ausführung von elektromagnetischen Pulsschweißungen.
Soudage par impulsion électromagnétique - Partie 2 : Conception des assemblages soudés
Le présent document spécifie les exigences de conception pour les soudures par impulsion électromagnétique et fournit des lignes directrices de conception pour le soudage par impulsion électromagnétique.
Elektromagnetno utripno varjenje - 2. del: Načrtovanje zvarnih spojev
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN 18007-2:2023
01-november-2023
Elektromagnetno utripno varjenje - 2. del: Načrtovanje zvarnih spojev
Electromagnetic pulse welding - Part 2: Design of welded joints
Schweißen und verwandte Verfahren - Elektromagnetisches Pulsschweißen - Teil 2:
Ausführung der Schweißverbindungen
Soudage par impulsion électromagnétique - Partie 2 : Conception des assemblages
soudés
Ta slovenski standard je istoveten z: prEN 18007-2
ICS:
25.160.10 Varilni postopki in varjenje Welding processes
25.160.40 Varjeni spoji in vari Welded joints and welds
oSIST prEN 18007-2:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 18007-2:2023
---------------------- Page: 2 ----------------------
oSIST prEN 18007-2:2023
DRAFT
EUROPEAN STANDARD
prEN 18007-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2023
ICS 25.160.10
English Version
Welding and allied processes - Electromagnetic pulse
welding - Part 2: Design of welded joints
Schweißen und verwandte Verfahren -
Elektromagnetisches Pulsschweißen - Teil 2:
Ausführung der Schweißverbindungen
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 121.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 18007-2:2023 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 18007-2:2023
prEN 18007-2:2023 (E)
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Design requirements . 5
4.1 Documentation . 5
4.2 Joint design . 5
4.2.1 General. 5
4.2.2 Welding of sheet metal parts . 5
4.2.3 Welding of cylindrical parts . 6
4.3 Additio
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.