iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

prEN 12597

(Main)

Bitumen and bituminous binders - Terminology

Bitumen and bituminous binders - Terminology

This European Standard defines terms for paving or industrial bitumen of various types and binders derived from bitumen.
This European Standard is intended to cover materials only within the scope of CEN/TC 336, i.e. only bitumens and bituminous binders. It should consequently not extend to non-petroleum "hydrocarbon" binders such as coal tar and its derivatives or to natural asphalts. However, some definitions are given for some excluded materials and related terms. The corresponding terms were introduced only when they appeared in a definition of a product or process and when their definition was found necessary for understanding or for avoiding any ambiguity.

Bitumen und bitumenhaltige Bindemittel - Terminologie

Bitumes et liants bitumineux - Terminologie

Bitumen in bitumenska veziva - Terminologija

General Information

Status
Not Published
Publication Date
18-Sep-2024
ICS
01.040.75 - Petroleum and related technologies (Vocabularies)
01.040.91 - Construction materials and building (Vocabularies)
75.140 - Waxes, bituminous materials and other petroleum products
91.100.50 - Binders. Sealing materials
Technical Committee
CEN/TC 336 - Bituminous binders
Drafting Committee
CEN/TC 336 - Bituminous binders
Current Stage
4599 - Dispatch of FV draft to CMC - Finalization for Vote
Start Date
27-Mar-2024
Due Date
01-Apr-2024
Completion Date
27-Mar-2024
Ref Project
oSIST prEN 12597:2023 - Bitumen and bituminous binders - Terminology

Relations

Revises
EN 12597:2014 - Bitumen and bituminous binders - Terminology
Effective Date
28-Jan-2023

Buy Standard

prEN 12597:2023prEN 12597:2023
PreviousNext
Draft
prEN 12597:2023
English, French and German language
24 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN 12597:2023
01-junij-2023
Bitumen in bitumenska veziva - Terminologija
Bitumen and bituminous binders - Terminology
Bitumen und bitumenhaltige Bindemittel - Terminologie
Bitumes et liants bitumineux - Terminologie
Ta slovenski standard je istoveten z: prEN 12597
ICS:
01.040.75 Naftna in sorodna tehnologija Petroleum and related
(Slovarji) technologies (Vocabularies)
01.040.91 Gradbeni materiali in gradnja Construction materials and
(Slovarji) building (Vocabularies)
75.140 Voski, bitumni in drugi naftni Waxes, bituminous materials
proizvodi and other petroleum products
91.100.50 Veziva. Tesnilni materiali Binders. Sealing materials
oSIST prEN 12597:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 12597:2023

---------------------- Page: 2 ----------------------
oSIST prEN 12597:2023


DRAFT
EUROPEAN STANDARD
prEN 12597
NORME EUROPÉENNE

EUROPÄISCHE NORM

April 2023
ICS Will supersede EN 12597:2014
English Version

Bitumen and bituminous binders - Terminology
Bitumes et liants bitumineux - Terminologie Bitumen und bitumenhaltige Bindemittel -
Terminologie
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 336.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 12597:2023 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 12597:2023
Contents / Sommaire / Inhaltsangabe Page
European foreword . 3
Avant-propos . 4
Vorwort . 5
1 Scope . 6
1 Domaine d'application . 6
1 Anwendungsbereich . 6
2 Normative references . 6
2 Références Normatives . 6
2 Normative Verweisungen . 6
3 Terms and definitions .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 12597:2014(Main)
Bitumen and bituminous binders - Terminology
SIST EN 12597:2014

This European Standard defines terms for paving or industrial bitumen of various types and binders derived from bitumen.
This European Standard is intended to cover materials only within the scope of CEN/TC 336, i.e. only bitumens and bituminous binders. It should consequently not extend to non-petroleum "hydrocarbon" binders such as coal tar and its derivatives or to natural asphalts. However, some definitions are given for some excluded materials and related terms. The corresponding terms were introduced only when they appeared in a definition of a product or process and when their definition was found necessary for understanding or for avoiding any ambiguity.
The materials covered by this European Standard are shown in Figure 1.
NOTE   Figure 1 also shows a clear distinction between materials inside and outside the scope of CEN/TC 336.

  • Standard
    17 pages
    English, French and German language
    sale 10% off
    e-Library read for
    1 day
CEN
prEN 12597(Main)
Bitumen and bituminous binders - Terminology
oSIST prEN 12597:2007

This EN specifies a method for determining the tensile properties of a bituminous binder, in particular those of polymer-modified bitumens by means of a force ductility test.

  • Draft
    15 pages
    English, French and German language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12597:2014(Main)
Bitumen and bituminous binders - Terminology
SIST EN 12597:2014

This European Standard defines terms for paving or industrial bitumen of various types and binders derived from bitumen.
This European Standard is intended to cover materials only within the scope of CEN/TC 336, i.e. only bitumens and bituminous binders. It should consequently not extend to non-petroleum "hydrocarbon" binders such as coal tar and its derivatives or to natural asphalts. However, some definitions are given for some excluded materials and related terms. The corresponding terms were introduced only when they appeared in a definition of a product or process and when their definition was found necessary for understanding or for avoiding any ambiguity.
The materials covered by this European Standard are shown in Figure 1.
NOTE   Figure 1 also shows a clear distinction between materials inside and outside the scope of CEN/TC 336.

  • Standard
    17 pages
    English, French and German language
    sale 10% off
    e-Library read for
    1 day
CEN
prEN 12597(Main)
Bitumen and bituminous binders - Terminology
oSIST prEN 12597:2007

This EN specifies a method for determining the tensile properties of a bituminous binder, in particular those of polymer-modified bitumens by means of a force ductility test.

  • Draft
    15 pages
    English, French and German language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 22435:2024(Main)
Gas cylinders - Cylinder valves with integrated pressure regulators - Specification and type testing (ISO 22435:2024)
kSIST FprEN ISO 22435:2024

This document specifies design, type test methods, marking and instruction requirements for cylinder valves with integrated pressure regulators (VIPRs) intended to be fitted to gas cylinders, pressure drums or tubes or used as a main valve for bundles of cylinders that convey compressed, liquefied or dissolved gases.
These are requirements for VIPRs that are in addition to those given in the relevant closure standard, for example, in ISO 10297 for cylinder valves, in ISO 17871 for quick-release cylinder valves, in ISO 17879 for self-closing cylinder valves or in ISO 23826 for ball valves. For ISO 17871, these requirements are only applicable to quick-release cylinder valves types B, C, D and E.
NOTE 1        If the pressure regulating system of a VIPR is acting as the primary valve operating mechanism, it is covered by the relevant closure standard, e.g. ISO 10297, ISO 17871, ISO 17879 and ISO 23826. This also includes designs where closure of the primary valve operating mechanism of a VIPR is obtained by closing the seat of the pressure regulating system.
NOTE 2        If the primary valve operating mechanism of a VIPR is located at the low-pressure side of the pressure regulating system, it is covered by the relevant closure standard, e.g. ISO 10297, ISO 17871, ISO 17879 and ISO 23826.
NOTE 3        The term “pressure receptacle” is used within this document to cover instances where no differentiation is necessary between gas cylinders, bundles of cylinders, pressure drums and tubes.
This document does not apply to VIPRs for
a)       medical applications (see ISO 10524-3);
b)       liquefied petroleum gas (LPG);
c)        cryogenic applications.
NOTE 4        Additional requirements for a VIPR with a residual pressure device (RPD) are specified in ISO 15996.
NOTE 5        Additional requirements for pressure relief valves can exist in international/regional regulations/ standards.

  • Draft
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17015-1:2024(Main)
Electronic Public Procurement - Catalogue - Part 1: Choreographies
kSIST FprEN 17015-1:2024

The purpose of this deliverable is to specify and describe choreographies for exchanging an electronic product catalogue (“catalogues”) as part of the business processes in the pre-award and post-award area, so that catalogues can serve as a basis for placing orders as well as evaluating tenders. The key aspects covered by this choreography specification are:
-   processes for submitting catalogues from the selling to the buying side;
-   processes for submitting catalogue-related data as part of a tendering process;
-   processes integrating sell-side procurement systems.
This document does not apply to the transactions used in the specified choreographies. These transactions are specified in EN 17015 2. The relationship between the choreographies and the transaction is described in Clause 8.
The identifier of this choreographies document is EN 17015 1:2024.
How to claim compliance to this choreography is specified in 6.2.3.

  • Draft
    38 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO/ASTM 52927:2024(Main)
Additive manufacturing - General principles - Main characteristics and corresponding test methods (ISO/ASTM 52927:2024)
kSIST FprEN ISO/ASTM 52927:2024

This document specifies the principal requirements applied to the testing of parts produced by additive manufacturing processes.
This document
—     identifies quality characteristics for feedstock and parts and the corresponding test procedures,
—     provides the specific procedures to build specimens using additive manufacturing process, and
—     recommends the scope and content of test and supply agreements.
This document is aimed at machine manufacturers, feedstock suppliers, AM system users, part providers, and customers to facilitate the communication on main quality characteristics. It applies wherever additive manufacturing processes are used.
NOTE            It is the intent to include, in future versions of this document, other characteristics such as thermal properties, electrical requirements and physical and physico-chemical properties based upon material types.

  • Draft
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 8362-2:2024(Main)
Injection containers and accessories - Part 2: Closures for injection vials (ISO 8362-2:2024)
SIST EN ISO 8362-2:2024

This document specifies the shape, dimensions, material, performance requirements and labelling of closures for injection vials covered by ISO 8362-1 and ISO 8362-4.
The dimensional requirements are not applicable to barrier-coated closures.
Closures specified in this document are intended for single use only.
NOTE            The potency, purity, stability and safety of a medicinal product during its manufacture and storage can strongly be affected by the nature and performance of the primary packaging.

  • Draft
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 16739-1:2024(Main)
Industry Foundation Classes (IFC) for data sharing in the construction and facility management industries - Part 1: Data schema (ISO 16739-1:2024)
kSIST FprEN ISO 16739-1:2024

This document represents an open international standard for information used in Building Information Modeling (BIM) that is exchanged and shared among software applications used by the various participants in the construction or facility management industry sector. This document includes definitions that cover information required for buildings and infrastructure works over their life cycle. This edition of the document added coverage of information required for infrastructure facilities including bridges, roads, railways, waterways and port facilities.
This document comprises the publication of a data schema, its documentation, the property and quantity set definitions and the mechanism of an exchange file format structure.
Definitions from this document are used to support different recognized work flows in the construction and facility management industry sector, representing information deliveries. Such information deliveries can be described according to ISO 29481.
Different implementation levels of this document can be defined to better support multiple information deliveries, they are referred to as a Model View Definition (MVD). Each MVD identifies which subset of the definitions of this document imposes requirements for implementation in software applications. Conforming software applications need to identify the model view definition they conform to when applying for software certification.
The following are within the scope of this edition of this document:
BIM exchange format definitions that are required during the life cycle phases of buildings and infrastructure:
demonstrating the need;
conception of need;
outline feasibility;
substantive feasibility study and outline financial authority;
outline conceptual design;
full conceptual design;
coordinated design;
procurement and full financial authority;
production information;
construction;
operation and maintenance.
BIM exchange format definitions that are required by the various disciplines involved within the life cycle phases:
architecture and civil engineering design;
service and utilities engineering;
structural engineering;
procurement;
construction planning;
facility and utility management;
project management;
client requirement management;
industry authorities for permits and approval.
BIM exchange format definitions including:
project structure;
physical components;
spatial components;
analysis items;
processes;
resources;
controls;
actors;
context definition.

  • Draft
    406 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 2620:2024(Main)
Analysis of natural gas - Biomethane - Determination of VOCs by thermal desorption gas chromatography with flame ionization and/or mass spectrometry detectors (ISO 2620:2024)
kSIST FprEN ISO 2620:2024

This document describes a method for sampling and analysis of volatile organic compounds (VOCs), including siloxanes, terpenes, organic sulfur compounds, in natural gas and biomethane matrices, using thermal desorption gas chromatography with flame ionization and/or mass spectrometry detectors (TD-GC-FID/MS).

  • Draft
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day