Welding consumables - Wire electrodes, wires and rods for welding of aluminium and aluminium alloys - Classification (ISO 18273:2015)

ISO 18273:2015 specifies requirements for classification of solid wires and rods for fusion welding of aluminium and aluminium alloys. The classification of the solid wires and rods is based on their chemical composition.

Schweißzusätze - Massivdrähte und -stäbe zum Schmelzschweißen von Aluminium und Aluminiumlegierungen - Einteilung (ISO 18273:2015)

Diese Internationale Norm legt Anforderungen für die Einteilung von Massivdrähten und Massivstäben zum Schmelzschweißen von Aluminium und Aluminiumlegierungen fest. Die Einteilung der Massivdrähte und Massivstäbe erfolgt nach ihrer chemischen Zusammensetzung.

Produits consommables pour le soudage - Fils-électrodes, fils et baguettes pour le soudage de l'aluminium et les alliages d'aluminium - Classification (ISO 18273:2015)

ISO 18273:2015 spécifie les exigences pour la classification des fils pleins et des baguettes pleines pour le soudage par fusion de l'aluminium et des alliages d'aluminium. La classification des fils pleins et des baguettes pleines est basée sur leur composition chimique.

Dodajni materiali za varjenje - Žice in palice za varjenje aluminija in aluminijevih zlitin - Razvrstitev (ISO 18273:2015)

Ta mednarodni standard določa zahteve za razvrstitev masivnih žic in palic za talilno
varjenje aluminija in aluminijevih zlitin. Razvrstitev masivnih žic in palic temelji
na kemični sestavi.

General Information

Status
Published
Publication Date
15-Dec-2015
Withdrawal Date
29-Jun-2016
Technical Committee
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
16-Dec-2015
Completion Date
16-Dec-2015

Relations

Buy Standard

Standard
EN ISO 18273:2016
English language
14 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-marec-2016
1DGRPHãþD
SIST EN ISO 18273:2004
Dodajni materiali za varjenje - Žice in palice za varjenje aluminija in aluminijevih
zlitin - Razvrstitev (ISO 18273:2015)
Welding consumables - Wire electrodes, wires and rods for welding of aluminium and
aluminium alloys - Classification (ISO 18273:2015)
Schweißzusätze - Massivdrähte und -stäbe zum Schmelzschweißen von Aluminium und
Aluminiumlegierungen - Einteilung (ISO 18273:2015)
Produits consommables pour le soudage - Fils-électrodes, fils et baguettes pour le
soudage de l'aluminium et les alliages d'aluminium - Classification (ISO 18273:2015)
Ta slovenski standard je istoveten z: EN ISO 18273:2015
ICS:
25.160.20 Potrošni material pri varjenju Welding consumables
77.120.10 Aluminij in aluminijeve zlitine Aluminium and aluminium
alloys
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 18273
EUROPEAN STANDARD
NORME EUROPÉENNE
December 2015
EUROPÄISCHE NORM
ICS 25.160.20 Supersedes EN ISO 18273:2004
English Version
Welding consumables - Wire electrodes, wires and rods for
welding of aluminium and aluminium alloys -
Classification (ISO 18273:2015)
Produits consommables pour le soudage - Fils- Schweißzusätze - Massivdrähte und -stäbe zum
électrodes, fils et baguettes pour le soudage de Schmelzschweißen von Aluminium und
l'aluminium et les alliages d'aluminium - Classification Aluminiumlegierungen - Einteilung (ISO 18273:2015)
(ISO 18273:2015)
This European Standard was approved by CEN on 15 August 2015.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 18273:2015 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
European foreword
This document (EN ISO 18273:2015) has been prepared by Technical Committee ISO/TC 44 "Welding
and allied processes" in collaboration with Technical Committee CEN/TC 121 “Welding and allied
processes” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by June 2016, and conflicting national standards shall be
withdrawn at the latest by June 2016.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document supersedes EN ISO 18273:2004.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 18273:2015 has been approved by CEN as EN ISO 18273:2015 without any modification.

INTERNATIONAL ISO
STANDARD 18273
Second edition
2015-11-15
Welding consumables — Wire
electrodes, wires and rods for welding
of aluminium and aluminium alloys —
Classification
Produits consommables pour le soudage — Fils-électrodes, fils et
baguettes pour le soudage de l’aluminium et les alliages d’aluminium
— Classification
Reference number
ISO 18273:2015(E)
©
ISO 2015
ISO 18273:2015(E)
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2015 – All rights reserved

ISO 18273:2015(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Classification . 1
4 Symbols and requirements . 5
4.1 Symbols for the product form . 5
4.2 Symbol for the chemical composition . 5
5 Mechanical properties of the weld metal . 5
6 Chemical analysis . 5
7 Rounding procedure . 5
8 Retest . 5
9 Technical delivery conditions . 6
10 Designation . 6
ISO 18273:2015(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical
Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 44, Welding and allied processes, Subcommittee
SC 3, Welding consumables.
This second edition cancels and replaces the first edition (ISO 18273:2004), which has been
technically revised.
Requests for official interpretations of any aspect of this International Standard should be directed to
the Secretariat of ISO/TC 44/SC 3, through your national standards body, a complete listing of which
can be found at www.iso.org.
iv © ISO 2015 – All rights reserved

ISO 18273:2015(E)
Introduction
For aluminium welding consumables, there is no unique relationship between the product form (solid
wire or rod) and the welding process used (e.g. gas shielded metal arc welding, gas tungsten arc
welding, plasma arc welding, or other welding processes). For this reason, the solid wires or rods can be
classified on the basis of any of the above product forms and can be used as appropriate for more than
one of the above processes.
INTERNATIONAL STANDARD ISO 18273:2015(E)
Welding consumables — Wire electrodes, wires and
rods for welding of aluminium and aluminium alloys —
Classification
1 Scope
This International Standard specifies requirements for classification of solid wires and rods for fusion
welding of aluminium and aluminium alloys. The classification of the solid wires and rods is based on
their chemical composition.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO 544, Welding consumables — Technical delivery conditions for filler materials and fluxes — Type of
product, dimensions, tolerances and markings
ISO 14344, Welding consumables — Procurement of filler materials and fluxes
ISO 80000-1:2009, Quantities and units — Part 1: General. Corrected by ISO 80000-1:2009/Cor 1:2011
3 Classification
The classification is divided into two parts.
a) The first part indicates the product form being solid wires or rods (see 4.1).
b) The second part gives a numerical symbol indicating the chemical composition of the solid wire or
rod (see Table 1).
The aluminium or aluminium alloy chemical composition limits specified are strictly identical to those
registered to the Aluminium Association, Washington, DC 20006, U.S.A. for the corresponding alloys.
ISO 18273:2015(E)
2 © ISO 2015 – All rights reserved
Table 1 — Symbol for the chemical composition of solid wires and rods
a
Alloy symbol Chemical composition in % (m/m)
Numerical Chemical Si Fe Cu Mn Mg Cr Zn Ga, V Ti Zr Al Be Other Other
(min.) each total
ALUMINIUM-LOW ALLOYED
Al 1070 Al99,7 0,20 0,25 0,04 0,03 0,03 – 0,04 V 0,05 0,03 – 99,70 0,000 3 0,03 –
Al 1080A Al99,8(A) 0,15 0,15 0,03 0,02 0,02 – 0,06 Ga 0,03 0,02 – 99,80 0,000 3 0,02 –
Al 1188 Al99,88 0,06 0,06 0,005 0,01 0,01 – 0,03 Ga 0,03 0,01 – 99,88 0,000 3 0,01 –
V 0,05
Al 1100 Al99,0Cu Si + Fe 0,95 0,05 to 0,20 0,05 – – 0,10 – – – 99,00 0,000 3 0,05 0,15
Al 1200 Al99,0 Si + Fe 1,00 0,05 0,05 – – 0,10 – 0,
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.