EN ISO 10350-2:2001

Plastics - Acquisition and presentation of comparable single-point data - Part 2: Long-fibre-reinforced plastics (ISO 10350-2:2001)

Migrated from Progress Sheet (TC Comment) (2000-07-10): new Tc forecast in Bp Bli 991026

Kunststoffe - Ermittlung und Darstellung vergleichbarer Einpunktkennwerte - Teil 2: Langfaserverstärkte Kunststoffe (ISO 10350-2:2001)

Diese Internationale Norm legt spezifische Prüfverfahren zur Ermittlung und Darstellung vergleichbarer Kennwerte für bestimmte grundlegende Eigenschaften von Kunststoffe fest. Im allgemeinen wird jede Eigenschaft durch einen einzelnen Messwert festgelegt, in bestimmten Fällen wird eine Eigenschaft jedoch durch zwei Werte charakterisiert, die unter verschiedenen Prüfbedingungen oder entlang unterschiedlicher Materialrichtungen ermittelt wurden? Die aufgeführten Eigenschaften werden vom Hersteller üblicherweise in Datenblättern erfasst. Die vorliegende Teil 2 der Norm gilt für thermoplastische und duroplastische Werkstoffe, die eine Verstärkung entweder durch diskontinuierliche Fasern mit einer Länge vor der Verarbeitung von mehr als 7,5mm oder durch kontinuierliche Fasern haben (z.B. Gewebe, kontinuierliche Matten aus Einzellitzen oder unidirektionale Kunststoffe). ISO 10350-1 behandelt speziell unverstärkte und gefüllte Kunststoffe sowie Kunststoffe mit Fasern, deren Länge weniger als 7,5mm beträgt.

Plastiques - Acquisition et présentation de caractéristiques intrinsèques comparables - Partie 2: Plastiques renforcés par de longues fibres (ISO 10350-2:2001)

L'ISO 10350 identifie des méthodes d'essai spécifiques en vue de l'acquisition et de la présentation de données comparables relatives à certaines propriétés de base des matières plastiques. En général, chaque propriété est spécifiée par une valeur expérimentale unique; toutefois, dans certains cas, certaines propriétés sont représentées par deux valeurs obtenues dans des conditions d'essai différentes ou dans différentes directions du matériau. Les propriétés indiquées sont celles qui sont traditionnellement présentées dans les fiches techniques des fabricants.  La présente Partie de l'ISO 10350 est applicable aux matériaux thermodurcissables ou thermoplastiques renforcés, dont les fibres de renforcement sont soit discontinues et d'une longueur supérieure à 7,5 mm avant la mise en oeuvre, soit continues (tissu, mat de fils de base continus ou unidirectionnels, par exemple). L'ISO 10350-1 traite spécifiquement des plastiques non renforcés et comportant des charges, y compris ceux qui comportent des fibres de moins de 7,5 mm de longueur.

Polimerni materiali - Pridobitev in predstavitev primerljivih značilnih enotočkovnih podatkov - 2. del: Z dolgimi vlakni ojačeni polimerni materiali (ISO 10350-2:2001)

General Information

• Status: Withdrawn
• Publication Date: 14-Jun-2001
• Withdrawal Date: 28-Feb-2011
• ICS: 83.120 - Reinforced plastics
• Technical Committee: CEN/TC 249 - Plastics
• Drafting Committee: CEN/TC 249 - Plastics
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 01-Mar-2011
• Completion Date: 01-Mar-2011
• Ref Project: SIST EN ISO 10350-2:2002 - Plastics - Acquisition and presentation of comparable single-point data - Part 2: Long-fibre-reinforced plastics (ISO 10350-2:2001)

Relations

• Replaces: EN ISO 10350:1995 - Plastics - Acquisition and presentation of comparable single-point data (ISO 10350:1993)
• Effective Date: 22-Dec-2008
• Replaced By: EN ISO 10350-2:2011 - Plastics - Acquisition and presentation of comparable single-point data - Part 2: Long-fibre-reinforced plastics (ISO 10350-2:2011)
• Effective Date: 05-Mar-2011

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 10350-2:2002
01-februar-2002
1DGRPHãþD
SIST EN ISO 10350:1999
3ROLPHUQLPDWHULDOL3ULGRELWHYLQSUHGVWDYLWHYSULPHUOMLYLK]QDþLOQLKHQRWRþNRYQLK
SRGDWNRYGHO=GROJLPLYODNQLRMDþHQLSROLPHUQLPDWHULDOL,62
Plastics - Acquisition and presentation of comparable single-point data - Part 2: Long-
fibre-reinforced plastics (ISO 10350-2:2001)
Kunststoffe - Ermittlung und Darstellung vergleichbarer Einpunktkennwerte - Teil 2:
Langfaserverstärkte Kunststoffe (ISO 10350-2:2001)
Plastiques - Acquisition et présentation de caractéristiques intrinseques comparables -
Partie 2: Plastiques renforcés par de longues fibres (ISO 10350-2:2001)
Ta slovenski standard je istoveten z: EN ISO 10350-2:2001
ICS:
83.120 2MDþDQLSROLPHUL Reinforced plastics
SIST EN ISO 10350-2:2002 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 10350-2:2002

---------------------- Page: 2 ----------------------

SIST EN ISO 10350-2:2002
EUROPEAN STANDARD
EN ISO 10350-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2001
ICS 83.120
English version
Plastics - Acquisition and presentation of comparable single-
point data - Part 2: Long-fibre-reinforced plastics (ISO 10350-
2:2001)
Plastiques - Acquisition et présentation de caractéristiques Kunststoffe - Ermittlung und Darstellung vergleichbarer
intrinsèques comparables - Partie 2: Plastiques renforcés Einpunktkennwerte - Teil 2: Langfaserverstärkte
par de longues fibres (ISO 10350-2:2001) Kunststoffe (ISO 10350-2:2001)
This European Standard was approved by CEN on 15 June 2001.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2001 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10350-2:2001 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 10350-2:2002
Page 2
EN ISO 10350-2:2001
CORRECTED 2001-08-15
Foreword
The text of the International Standard ISO 10350-2:2001 has been prepared by Technical
Committee ISO/TC 61 "Plastics" in collaboration with Technical Committee CEN/TC 249
"Plastics", the secretariat of which is held by IBN.
This European Standard shall be given the status of a national standard, either by publication
of an identical text or by endorsement, at the latest by December 2001, and conflicting
national standards shall be withdrawn at the latest by December 2001.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy,
Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United
Kingdom.
Endorsement notice
The text of the International Standard ISO 10350-2:2001 was approved by CEN as a
European Standard without any modification.
NOTE: Normative references to International Standards are listed in annex ZA (normative).

---------------------- Page: 4 ----------------------

SIST EN ISO 10350-2:2002
Page 3
EN ISO 10350-2:2001
Annex ZA (normative)
Normative references to international publications
with their relevant European publications
This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions
of any of these publications apply to this European Standard only when incorporated in it by
amendment or revision. For undated references the latest edition of the publication referred to
applies (including amendments).
NOTE Where an International Publication has been modified by common modifications,
indicated by (mod.), the relevant EN/HD applies.
Publication Year Title EN Year
ISO 62 199
...