Ductile iron pipes, fittings, accessories and their joints for sewerage applications - Requirements and test methods

This European Standard specifies the requirements and associated test methods applicable to ductile iron pipes,
fittings, accessories and their joints for the construction of drains and sewers outside buildings:
- operating without pressure (gravity sewerage), or with positive or negative pressure (see Table 5);
- to be installed below or above ground;
- to convey surface water, domestic waste water and certain types of industrial effluents, either in separate systems
or in combined systems.
This European Standard applies to pipes, fittings and accessories which are:
- manufactured with socketed, flanged or spigot ends;
- normally delivered externally and internally coated;
- suitable for continuous fluid temperatures between 0 °C excluding frost, and 45 °C for DN ≤ 200 or 35 °C for
DN > 200, according to EN 476;
- not intended for use in areas subject to reaction to fire regulations.
NOTE 1 This does not preclude special arrangements for the products to be used at higher temperatures.
This European Standard covers pipes, fittings and accessories cast by any type of foundry process or manufactured
by fabrication of cast components, as well as corresponding joints, of a size range extending from DN 80 to DN 2000
inclusive.
This European Standard specifies requirements for materials, dimensions and tolerances, mechanical properties and
standard coatings of ductile iron pipes and fittings. It also gives performance requirements for all components
including joints. Joint design and gasket shapes are outside the scope of this European Standard.
NOTE 2 In this European Standard, all pressures are relative pressures, expressed in bars (100 kPa = 1 bar).

Rohre, Formstücke, Zubehörteile aus duktilem Gusseisen und ihre Verbindungen für die Abwasser-Entsorgung - Anforderungen und Prüfverfahren

Diese Europäische Norm legt die Anforderungen und die entsprechenden Prüfverfahren für duktile Gussrohre, Formstücke, Zubehörteile und deren Verbindungen fest, die für die Errichtung von EntwAbwäasserungs leitungen und  Abwasserleitungen kanälen außerhalb von Gebäuden verwendet werden, wie:und
   zum Betrieb vonals Freispiegelleitungen (Schwerkraftentwässerungssysteme) sowieoder untermit positivem oder negativem Druck (siehe Tabelle 5) betrieben werden;,
   erdüberdeckt oder oberirdisch eingebaut werden,;
   zum Transport von Oberflächenwasser, häuslichem Abwasser und bestimmten Arten von Industrieab¬wässern, entweder in Trenn  oder in Mischwassersystemen betrieben werden.
Diese Europäische Norm gilt für Rohre, Formstücke und Zubehörteile, die:
   mit Muffen, Flanschen oder Einsteckenden hergestellt werden;
   normalerweise mit einem Innen  und Außenschutz geliefert werden;
   für dauernde Flüssigkeitstemperaturen zwischen 0 °C, Frost ausgenommen, und 45 °C für DN  200 oder 35 °C für DN  200 geeignet sind, entsprechend nach EN 476;
   nicht vorgesehen sind für die Anwendung in GebietBereichen, die den BrandbBestimmungen zum Brandverhalten unterliegen.
ANMERKUNG 1   Dies schließt besondere Vereinbarungen für die Verwendung dieser Produkte bei höheren Temperaturen zu verwendenden Produkte nicht aus.
Diese Europäische Norm gilt für Rohre, Formstücke und Zubehörteile, die nach einem beliebigen Gießverfahren oder aus gegossenen Einzelteilen hergestellt werden, genauso wie für die entsprechenden Verbindungen für den Nennweitenbereich von DN 80 bis einschließlich DN 2 000.
Diese Europäische Norm legt Anforderungen an Werkstoffe, Abmessungen und Grenzabmaße, mechanische Eigenschaf¬ten und die Standardüberzüge und Auskleidungen von Rohren und Formstücken aus duktilem Gusseisen fest.

Tuyaux, raccords et accessoires en fonte ductile et leurs assemblages pour l'assainissement - Prescriptions et méthodes d'essai

La présente Norme européenne spécifie les prescriptions et les méthodes d'essai associées applicables aux tuyaux, raccords et accessoires en fonte ductile et à leurs assemblages, destinés à la construction de collecteurs et de branchements d'assainissement à l'extérieur des bâtiments :
-   fonctionnant sans pression (assainissement à écoulement libre) ou sous pression positive ou négative ;
-   mis en �uvre dans le sol ou en élévation ;
-   pour transporter les eaux de surface, les eaux usées domestiques et certains types d'effluents industriels, en système séparatif ou en système unitaire.
La présente norme s'applique aux tuyaux, raccords et accessoires qui sont :
-   fabriqués avec des extrémités à emboîture, à bride ou à bout uni ;
-   normalement livrés revêtus extérieurement et intérieurement ;
-   utilisables pour des températures de fluide en régime continu comprises entre 0 °C, gel exclus, et 45 °C pour DN £ 200 ou 35 °C pour DN > 200, conformément à l'EN 476.
NOTE   Des températures de fonctionnement supérieures peuvent être admises par accord entre le fabricant et le client.
La présente norme traite des tuyaux, raccords et accessoires moulés par tout procédé de fonderie ou fabriqués à partir de composants moulés, ainsi que les assemblages correspondants, pour la gamme des DN 80 à DN 2 000 inclus.
La présente norme spécifie les prescriptions relatives aux matériaux, aux dimensions et aux tolérances, aux propriétés mécaniques et aux revêtements normalisés des tuyaux et raccords en fonte ductile. Elle indique aussi les prescriptions de performance de tous les composants y compris les assemblages. La conception des assemblages et la forme des garnitures de joints sortent du domaine d'application de la présente norme.
NOTE   Dans la présente norme, toutes les pressions sont des pressions relatives exprimées en bars (100 kPa = 1 bar).

Cevi, fitingi in dodatki iz nodularne litine za kanalizacijo - Zahteve in preskusne metode

General Information

Status
Withdrawn
Publication Date
02-Oct-2007
Withdrawal Date
23-Jun-2009
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
24-Jun-2009
Completion Date
24-Jun-2009

Relations

Buy Standard

Standard
EN 598:2008
English language
66 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 598:2008
01-marec-2008
1DGRPHãþD
SIST EN 598:1998
Cevi, fitingi in dodatki iz nodularne litine za kanalizacijo - Zahteve in preskusne
metode
Ductile iron pipes, fittings, accessories and their joints for sewerage applications -
Requirements and test methods
Rohre, Formstücke, Zubehörteile aus duktilem Gusseisen und ihre Verbindungen für die
Abwasser-Entsorgung - Anforderungen und Prüfverfahren
Tuyaux, raccords et accessoires en fonte ductile et leurs assemblages pour
l'assainissement - Prescriptions et méthodes d'essai
Ta slovenski standard je istoveten z: EN 598:2007
ICS:
23.040.10 Železne in jeklene cevi Iron and steel pipes
23.040.40 Kovinski fitingi Metal fittings
93.030 Zunanji sistemi za odpadno External sewage systems
vodo
SIST EN 598:2008 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 598:2008

---------------------- Page: 2 ----------------------

SIST EN 598:2008
EUROPEAN STANDARD
EN 598
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2007
ICS 23.040.40; 23.040.10 Supersedes EN 598:1994
English Version
Ductile iron pipes, fittings, accessories and their joints for
sewerage applications - Requirements and test methods
Tuyaux, raccords et accessoires en fonte ductile et leurs Rohre, Formstücke, Zubehörteile aus duktilem Gusseisen
assemblages pour l'assainissement - Prescriptions et und ihre Verbindungen für die Abwasser-Entsorgung -
méthodes d'essai Anforderungen und Prüfverfahren
This European Standard was approved by CEN on 11 August 2007.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2007 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 598:2007: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 598:2008
EN 598:2007 (E)
Contents Page
Foreword.5
1 Scope .6
2 Normative references .6
3 Terms and definitions .7
4 Technical requirements .10
4.1 General.10
4.2 Dimensional requirements.12
4.3 Material characteristics.14
4.4 Coatings and linings for pipes .15
4.5 Coatings for fittings and accessories.18
4.6 Marking of pipes and fittings.18
4.7 Leak tightness.18
5 Performance requirements .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.