EN 4002:2007

Aerospace series - Aluminium alloy AL-P2219-T81 - Sheet and strip 0,5 mm ≤ a ≤ 6 mm

This standard specifies the requirements relating to:
Aluminium alloy AL-P2219-T81 - Sheet and strip 0,5 mm

Luft- und Raumfahrt - Aluminiumlegierung AL-P2219-T81 - Bleche und Bänder 0,5 mm  a  6 mm

Série aérospatiale - Alliage d'aluminium AL-P2219-T81 - Tôles et bandes 0,5 mm  a  6 mm

Aeronavtika - Aluminijeva zlitina AL-P2219-T81 - Pločevina in trakovi 0,5 mm <= a <= 6 mm

General Information

• Status: Published
• Publication Date: 21-Aug-2007
• Withdrawal Date: 28-Feb-2008
• ICS: 77.150.10 - Aluminium products
• Technical Committee: ASD-STAN - Aerospace
• Drafting Committee: ASD-STAN/D 4 - Metallic
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 22-Aug-2007
• Completion Date: 22-Aug-2007
• Ref Project: SIST EN 4002:2007 - Aerospace series - Aluminium alloy AL-P2219-T81 - Sheet and strip 0,5 mm <= a <= 6 mm

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 4002:2007
01-november-2007
$HURQDYWLND$OXPLQLMHYD]OLWLQD$/373ORþHYLQDLQWUDNRYLPP D
 PP
Aerospace series - Aluminium alloy AL-P2219-T81 - Sheet and strip 0,5 mm <= a <= 6
mm
Luft- und Raumfahrt - Aluminiumlegierung AL-P2219-T81 - Bleche und Bänder 0,5 mm
<= a <= 6 mm
Série aérospatiale - Alliage d'aluminium AL-P2219-T81 - Tôles et bandes 0,5 mm <= a
<= 6 mm
Ta slovenski standard je istoveten z: EN 4002:2007
ICS:
49.025.20 Aluminij Aluminium
SIST EN 4002:2007 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 4002:2007

---------------------- Page: 2 ----------------------

SIST EN 4002:2007


EUROPEAN STANDARD
EN 4002

NORME EUROPÉENNE

EUROPÄISCHE NORM
August 2007
ICS 77.150.10
English Version
Aerospace series - Aluminium alloy AL-P2219-T81 - Sheet and
strip 0,5 mm ≤ a ≤ 6 mm
Série aérospatiale - Alliage d'aluminium AL-P2219-T81 - Luft- und Raumfahrt - Aluminiumlegierung AL-P2219-T81 -
Tôles et bandes 0,5 mm ≤ a ≤ 6 mm Bleche und Bänder 0,5 mm ≤ a ≤ 6 mm
This European Standard was approved by CEN on 12 June 2006.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.






EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2007 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 4002:2007: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 4002:2007
EN 4002:2007 (E)
Contents
Foreword.3
Introduction .4
1 Scope .4
2 Normative references .4

2

---------------------- Page: 4 ----------------------

SIST EN 4002:2007
EN 4002:2007 (E)
Foreword
This document (EN 4002:2007) has been prepared by the AeroSpace and Defense Industries Association of
Europe - Standardization (ASD-STAN).
After enquiries and votes carried out in accordance with the rules of this Association, this Standard has
received the approval of the National Associations and the Official Services of the member countries of ASD,
prior to its presentation to CEN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by February 2008, and conflicting national standards shall be withdrawn
at the latest by February 2008.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.

3

---------------------- Page: 5 ----------------------

SIST EN 4002:2007
EN 4002:2007 (E)
Introduction
This standard is part of the series of EN metallic material standards for aerospace applications. The general
organization of this series is described in EN 4258.
This standard has been prepared in accordance with EN 4500-2.
1 Scope
This standard specifies the requirements relating to:
Aluminium alloy AL-P2219-T81 — Sheet and strip 0
...