CEN/TS 15658:2007

Advanced technical ceramics - Mechanical properties of ceramic fibres at high temperature under non-reactive environment - Determination of creep behaviour by the hot end method

This Technical Specification specifies the conditions for the determination of the tensile creep deformation and failure behaviour of single filaments of ceramic fibres at high temperature and under test conditions that prevent changes to the material as a result of chemical reaction with the test environment.
This Technical Specification applies to continuous ceramic filaments taken from tows, yarns, braids and knitted structures, that have strains to failure less than or equal to 5 %.

Hochleistungskeramik - Mechanische Eigenschaften von Keramikfasern bei hohen Temperaturen in einer reaktionsfreien Umgebung - Bestimmung des Kriechverhaltens im Heißverbindungsverfahren

Céramiques techniques avancées - Propriétés mécaniques des fibres céramiques à haute température sous environnement non réactif - Détermination du comportement au fluage par la méthode des mors chauds

La présente Spécification technique fixe les conditions de détermination de la déformation par fluage en traction et le comportement en cas de défaillance d’un filament de fibre céramique à haute température et dans des conditions d’essai permettant d’empêcher tout modification du matériau lié à une réaction chimique avec l’environnement d’essai.
La présente Spécification technique s’applique à des filaments céramiques continus issus de mèches, fils, tresses et tricots, ayant des allongements à la rupture inférieurs ou égaux à 5 %.

Sodobna tehnična keramika - Mehanske lastnosti keramičnih vlaken pri visokih temperaturah v nereaktivnem okolju - Določitev lezenja po metodi vročega spajanja (hot end method)

General Information

• Status: Published
• Publication Date: 18-Sep-2007
• ICS: 81.060.30 - Advanced ceramics
• Technical Committee: CEN/TC 184 - Advanced technical ceramics
• Drafting Committee: CEN/TC 184/SC 1 - Ceramic composites
• Current Stage: 9093 - Decision to confirm - Review Enquiry
• Start Date: 10-Oct-2013
• Completion Date: 10-Oct-2013
• Ref Project: SIST-TS CEN/TS 15658:2007 - Advanced technical ceramics - Mechanical properties of ceramic fibres at high temperature under non-reactive environment - Determination of creep behaviour by the hot end method

Standards Content (Sample)

SLOVENSKI STANDARD
SIST-TS CEN/TS 15658:2007
01-december-2007
6RGREQDWHKQLþQDNHUDPLND0HKDQVNHODVWQRVWLNHUDPLþQLKYODNHQSULYLVRNLK
WHPSHUDWXUDKYQHUHDNWLYQHPRNROMX'RORþLWHYOH]HQMDSRPHWRGLYURþHJD
VSDMDQMDKRWHQGPHWKRG
Advanced technical ceramics - Mechanical properties of ceramic fibres at high
temperature under non-reactive environment - Determination of creep behaviour by the
hot end method
Hochleistungskeramik - Mechanische Eigenschaften von Keramikfasern bei hohen
Temperaturen in einer reaktionsfreien Umgebung - Bestimmung des Kriechverhaltens im
Heißverbindungsverfahren
Céramiques techniques avancées - Propriétés mécaniques des fibres céramiques a
haute température sous environnement non réactif - Détermination du comportement au
fluage par la méthode des mors chauds
Ta slovenski standard je istoveten z: CEN/TS 15658:2007
ICS:
81.060.30 Sodobna keramika Advanced ceramics
SIST-TS CEN/TS 15658:2007 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

TECHNICAL SPECIFICATION
CEN/TS 15658
SPÉCIFICATION TECHNIQUE
TECHNISCHE SPEZIFIKATION
September 2007
ICS 81.060.30

English Version
Advanced technical ceramics - Mechanical properties of ceramic
fibres at high temperature under non-reactive environment -
Determination of creep behaviour by the hot end method
Céramiques techniques avancées - Propriétés mécaniques Hochleistungskeramik - Mechanische Eigenschaften von
des fibres céramiques à haute température sous Keramikfasern bei hohen Temperaturen in einer
environnement non réactif - Détermination du reaktionsfreien Umgebung - Bestimmung des
comportement au fluage par la méthode des mors chauds Kriechverhaltens im Heißverbindungsverfahren
This Technical Specification (CEN/TS) was approved by CEN on 20 August 2007 for provisional application.
The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their
comments, particularly on the question whether the CEN/TS can be converted into a European Standard.
CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available
promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS)
until the final decision about the possible conversion of the CEN/TS into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2007 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TS 15658:2007: E
worldwide for CEN national Members.

---------------------- Page: 2 ----------------------

CEN/TS 15658:2007 (E)
Contents Page
Foreword.3
1 Scope .4
2 Normative references .4
3 Terms and definitions .4
4 Principle.7
5 Significance and use .7
6 Apparatus .7
6.1 Test installations.7
6.2 Load train.7
6.3 Adhesive .7
6.4 Test chamber.
...