EN 1337-2:2004

Structural bearings - Part 2: Sliding elements

This European Standard specifies the characteristics for the design and manufacture of sliding elements and guides which are not structural bearings but only parts of them for combination with structural bearings as defined in other Parts of this European Standard.
Suitable combinations are shown in Table 1 of EN 1337-1:2000.
Sliding surfaces with a diameter of the circumscribing circle of single or multiple PTFE sheets less than 75 mm or greater than 1500 mm, or with effective bearing temperatures less than -35°C or greater than 48°C are outside the scope of this European Standard.
Sliding elements for use as temporary devices during construction, for example during launching of the superstructure, are also outside the scope of this European Standard.
In this standard the specification is also given for curved sliding surfaces which are not part of separate sliding elements but which are incorporated in cylindrical or spherical PTFE bearings as per EN 1337.
NOTE     The general principles detailed in this European Standard may be applied for sliding elements outside this scope, but their suitability for the intended use should be proven.

Lager im Bauwesen - Teil 2: Gleitteile

Diese Europäische Norm legt Angaben für Bemessung und Herstellung von Gleitteilen und Führungen fest, die keine Lager, sondern nur Teile von solchen sind, für die Kombination mit Lagern, die in anderen Teilen dieser Norm geregelt sind.
Geeignete Kombinationen sind in EN 1337-1:2000, Tabelle 1 angegeben.
Gleitflächen aus ein- oder mehrteiligen PTFE-Platten, deren umschreibender Kreis einen Durchmesser von weniger als 75 mm oder mehr als 1500 mm hat oder deren wirksame Lagertemperatur niedriger als - 35 °C oder höher als 48 °C ist, liegen außerhalb des Anwendungsbereichs dieser Norm.
Gleitelemente, die vorübergehend als Hilfslager während der Bauphase dienen (z. B. beim Taktschieben des Überbaus), liegen außerhalb des Anwendungsbereichs dieser Norm.
In dieser Norm sind auch Angaben für gekrümmte Gleitflächen enthalten, die nicht Teile von separaten Gleitteilen sind, sondern die in Kalotten- und Zylinderlagern nach EN 1337-7 eingebaut werden.
ANMERKUNG   Die in dieser Europäischen Norm beschriebenen Grundsätze dürfen für Gleitelemente angewendet werden, die außerhalb dieses Anwendungsbereiches liegen, jedoch ist deren Brauchbarkeit für den vorgeschriebenen Verwendungszweck nachzuweisen.

Appareils d'appui structuraux - Partie 2: Éléments de glissement

Konstrukcijska ležišča - 2. del: Drsni elementi

General Information

• Status: Published
• Publication Date: 16-Mar-2004
• ICS: 91.010.30 - Technical aspects
• Technical Committee: CEN/TC 167 - Structural bearings
• Drafting Committee: CEN/TC 167/WG 3 - Sliding, spherical and cylindrical elements
• Current Stage: 9092 - Decision on results of review/2YR ENQ - revise - Review Enquiry
• Start Date: 14-Mar-2008
• Completion Date: 14-Mar-2008
• Directive: 305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
• Directive: 89/106/EEC - Construction products
• Mandate: M/104 - Mandate to CEN/CENELEC concerning the execution of standardization work for harmonized standards on structural bearings
• Ref Project: SIST EN 1337-2:2004 - Structural bearings - Part 2: Sliding elements

Relations

• Replaces: EN 1337-2:2000 - Structural bearings - Part 2: Sliding elements
• Effective Date: 22-Dec-2008
• Revised: prEN 1337-2 - Structural bearings - Part 2: Sliding elements
• Effective Date: 19-Jan-2023

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Lager im Bauwesen - Teil 2: GleitteileAppareils d'appui structuraux - Partie 2: Éléments de glissementStructural bearings - Part 2: Sliding elements91.010.30Technical aspectsICS:Ta slovenski standard je istoveten z:EN 1337-2:2004SIST EN 1337-2:2004en01-junij-2004SIST EN 1337-2:2004SLOVENSKI
STANDARDSIST EN 1337-2:20011DGRPHãþD

EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 1337-2March 2004ICS 91.010.30Supersedes EN 1337-2:2000English versionStructural bearings - Part 2: Sliding elementsAppareils d'appui structuraux - Partie 2: Eléments deglissementLager im Bauwesen - Teil 2: GleitteileThis European Standard was approved by CEN on 2 January 2004.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2004 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 1337-2:2004: ESIST EN 1337-2:2004

Reduced area for sliding elements.35Annex B (informative)
Coefficient of friction for dimpled PTFE sheets.37Annex C (informative)
Method for calculating the deformation of backing plates attached to concrete.38Annex D (normative)
Test methods for friction.39Annex E (normative)
Hard chromium plated surfaces - Ferroxyl test.50Annex F (normative)
Thickness measurement of the anodized surfaces.52Annex G (normative)
Lubricant - Oil separation test.54Annex H (normative)
Oxidation stability of lubricant.57Annex J (normative)
Austenitic steel sheets adhesive - Lap shear test.63Annex K (normative)
Factory Production Control (FPC).66Annex L (informative)
Audit testing.69Bibliography.70SIST EN 1337-2:2004
...