CEN/TS 15412:2006
(Main)Solid recovered fuels - Methods for the determination of metallic aluminium
Solid recovered fuels - Methods for the determination of metallic aluminium
This Technical Specification specifies two different methods for the determination of metallic aluminium in solid recovered fuels:
method a: dissolution of metallic aluminium and analysis by Inductively Coupled Plasma Optic Emission Spectrometry (ICP-OES) or by Flame Atomic Absorption Spectrometry (FAAS);
method b: Differential Thermal Analysis (DTA) on the solid SRF.
Feste Sekundärbrennstoffe - Verfahren zur Bestimmung des Gehaltes an metallischem Aluminium
Combustibles solides de récupération - Méthodes pour la détermination de l'aluminium métal
Trdno alternativno gorivo - Metode za določevanje aluminija v kovinski obliki
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST-TS CEN/TS 15412:2007
01-marec-2007
7UGQRDOWHUQDWLYQRJRULYR0HWRGH]DGRORþHYDQMHDOXPLQLMDYNRYLQVNLREOLNL
Solid recovered fuels - Methods for the determination of metallic aluminium
Feste Sekundärbrennstoffe - Verfahren zur Bestimmung des Gehaltes an metallischem
Aluminium
Combustibles solides de récupération - Méthodes pour la détermination de l'aluminium
métal
Ta slovenski standard je istoveten z: CEN/TS 15412:2006
ICS:
75.160.10 Trda goriva Solid fuels
SIST-TS CEN/TS 15412:2007 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
TECHNICAL SPECIFICATION
CEN/TS 15412
SPÉCIFICATION TECHNIQUE
TECHNISCHE SPEZIFIKATION
September 2006
ICS 75.160.10
English Version
Solid recovered fuels - Methods for the determination of metallic
aluminium
Combustibles solides de récupération - Méthodes pour la Feste Sekundärbrennstoffe - Verfahren zur Bestimmung
détermination de l'aluminium métal des Gehaltes an metallischem Aluminium
This Technical Specification (CEN/TS) was approved by CEN on 25 March 2006 for provisional application.
The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their
comments, particularly on the question whether the CEN/TS can be converted into a European Standard.
CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available
promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS)
until the final decision about the possible conversion of the CEN/TS into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2006 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TS 15412:2006: E
worldwide for CEN national Members.
---------------------- Page: 2 ----------------------
CEN/TS 15412:2006 (E)
Contents Page
Foreword.3
Introduction.4
1 Scope .5
2 Normative references .5
3 Terms and definitions .5
4 Safety remarks .5
5 Principle.6
6 Apparatus .6
7 Reagents.7
8 Preparation of the test sample .7
9 Procedure .8
10 Calculation and evaluation .9
11 Quality control .9
12 Performance characteristics .10
13 Test report .10
Annex A (normative) Guidelines - Characteristics of the laboratory sample for chemical
analysis of SRF .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.