EN ISO 5981:1997

Rubber- or plastics-coated fabrics - Determination of resistance to combined shear flexing and rubbing (ISO 5981:1997)

This standard specifies a method for determination of flex abrasion of rubber or plastics coated fabrics.

Mit Kautschuk oder Kunststoff beschichtete Textilien - Bestimmung des Widerstandes gegen kombiniertes Knautschen und Reiben (ISO 5981:1997)

Die vorliegende Internationale Norm legt zwei Verfahren zur Beurteilung des Widerstandes von mit Kautschuk oder Kunststoff beschichteten Textilien gegen kombiniertes Knautschen und Reiben fest. Die Beanspruchung durch Reiben wird entweder durch Verwendung eines Anpreßfußes (Verfahren A) erzwungen oder durch einfache Berührung zwischen den Oberflächen der Probekörper hervorgerufen (Verfahren B).

Supports textiles revêtus de caoutchouc ou de plastique - Détermination de la résistance au froissement dû à l'application simultanée d'un couple et de frottement (ISO 5981:1997)

Gumirane ali plastificirane tekstilije - Ugotavljanje odpornosti proti kombiniranemu učinku mečkanj in drgnenj (ISO 5981:1997)

General Information

• Status: Withdrawn
• Publication Date: 14-Jun-1997
• Withdrawal Date: 14-Oct-2007
• ICS: 59.080 - Products of the textile industry
• Technical Committee: CEN/TC 248 - Textiles and textile products
• Drafting Committee: CEN/TC 248/WG 4 - Coated fabrics
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 15-Oct-2007
• Completion Date: 15-Oct-2007
• Ref Project: SIST EN ISO 5981:1999 - Rubber- or plastics-coated fabrics - Determination of resistance to combined shear flexing and rubbing (ISO 5981:1997)

Relations

• Replaced By: EN ISO 5981:2007 - Rubber- or plastics-coated fabrics - Determination of resistance to combined shear flexing and rubbing (ISO 5981:2007)
• Effective Date: 22-Dec-2008

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 5981:1999
01-marec-1999
*XPLUDQHDOLSODVWLILFLUDQHWHNVWLOLMH8JRWDYOMDQMHRGSRUQRVWLSURWLNRPELQLUDQHPX
XþLQNXPHþNDQMLQGUJQHQM,62
Rubber- or plastics-coated fabrics - Determination of resistance to combined shear
flexing and rubbing (ISO 5981:1997)
Mit Kautschuk oder Kunststoff beschichtete Textilien - Bestimmung des Widerstandes
gegen kombiniertes Knautschen und Reiben (ISO 5981:1997)
Supports textiles revetus de caoutchouc ou de plastique - Détermination de la résistance
au froissement du a l'application simultanée d'un couple et de frottement (ISO
5981:1997)
Ta slovenski standard je istoveten z: EN ISO 5981:1997
ICS:
59.080.40 3RYUãLQVNRSUHYOHþHQH Coated fabrics
WHNVWLOLMH
SIST EN ISO 5981:1999 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 5981:1999

---------------------- Page: 2 ----------------------

SIST EN ISO 5981:1999

---------------------- Page: 3 ----------------------

SIST EN ISO 5981:1999

---------------------- Page: 4 ----------------------

SIST EN ISO 5981:1999

---------------------- Page: 5 ----------------------

SIST EN ISO 5981:1999

---------------------- Page: 6 ----------------------

SIST EN ISO 5981:1999
INTERNATIONAL IS0
STANDARD
5981
Second edition
1997-06-I 5
Rubber- or plastics-coated fabrics -
Determination of resistance to combined
shear flexing and rubbing
Supports textiles reMus de caoutchouc ou de plastique - DBtermination
de la ksistance au froissement dil ;i /‘application simultarke d ’un couple
et de frottement
Reference number
IS0 5981 :I 997(E)

---------------------- Page: 7 ----------------------

SIST EN ISO 5981:1999
IS0 5981: 1997(E)
Foreword
IS0 (the International Organization for Standardization) is a worldwide
federation of national standards bodies (IS0 member bodies). The work of
preparing International Standards is normally carried out through IS0
technical committees. Each member body interested in a subject for which
a technical committee has been established has the right to be represented
on that committee. International organizations, governmental and non-
governmental, in liaison with ISO, also take part in the work. IS0
collaborates closely with the International Electrotechnical Commission
(IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting
a vote.
International Standard IS0 5981 was prepared by Technical Committee
ISOAC 45, Rubber and rubber products.
This second edition cancels and replaces the first edition (IS0 5981:1982),
which has been technically revised.
0 IS0 1997
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced
or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case postale 56 l CH-1211 Geneve 20 l Switzerland
Internet central @ iso.ch
x.400
c=ch; a=4OOnet; p=iso; o=isocs; s=central
Printed in Switzerland
ii

---------------------- Page: 8 ----------------------

SIST EN ISO 5981:1999
INTERNATIONAL STANDARD @ IS0 IS0 5981:1997(E)
Rubber- or plastics-coated fabrics - Determination of resistance
to combined shear flexing and rubbing
WARNING - Persons using this International Standard should be familiar with normal laboratory practice.
This standard does not purport to address all of the safety problems, if any, associated with its use.
It is the responsibility of the user to establish appropriate safety and health practices and to ensure
compliance with any national regulatory conditions.
1 Scope
This International Standard specifies two methods of evaluating the resistance to combined shear flexing and
rubbing of rubber- or plastics-coated fabrics. Rubbing is either forced by application of a pressure foot (method A),
or is caused by simple contact between the faces of the test pieces (method B).
Method B (without application of the pressure foot) is preferred in all cases where the foot would damage the test
piece through an abrasive effect, e.g. materials with sticky surfaces, light coatings such as polyurethanes on rough
surfaces.
The test may be carried out on products as delivered or after pre-treatments such as wetting or accelerated ageing.
NOTE - The results using method A and method B should not be compared as there is no correlation between the two
methods.
2 Normative references
The following standards contain provisions which, through reference in this text, constitute provisions of this
International Standard. At the time of publication, the editions indicated were valid. All standards are subject to
revision, and parties to agreements based on this International Standard are encouraged to investigate the
possibility of applying the most recent editions of the standards indicated below. Members of IEC and IS0 maintain
registers of currently valid International Standards.
- Method of indicating surface texture.
IS0 1302: 1992 Technical drawings
IS0 2231: 1989, Rubber- or plastics-coated fabrics - Standard atmospheres for conditioning and testing.
IS0 2286-l : -I), Rubber- or plastics-coated fabrics - Determination of roll characteristics -Pat? I: Methods for
determination of the length, width and net mass of a roll.
1) To be published. (Revision, in parts, of IS0 2286:1986)

---------------------- Page: 9 ----------------------

SIST EN ISO 5981:1999
0 IS0
IS0 5981:1997(E)
3 Principle
A test piece is subjected to a succession of mild abrasive rubs applied to a continuously changing pattern of folds
created by a rubbing machine. The damage caused to the test piece is assessed visually.
4 Apparatus
4.1 General
The apparatus shall consist of a rubbing machine (see figures 1 and 2) having two parallel clamps giving contra-
reciprocating motions defined by their length and width, and a foot (optional) pressing on the flexing part of the test
piece.
The apparatus shall be equipped with a counter and a device making it possible to bring the two clamps into
juxtaposition manually.
Most counters, because of their method of drive, record only one impulse for one back and forth movement of the
clamps, i.e. two rubbings. In this case, the number indicated by the counter shall be multiplied by 2 in order to obtain
the number of rubbings (example: counter at 1 000, number of corresponding rubbings 2 000).
The components of the rubbing machine shall comply with the requirements specified in 4.2, 4.3 and 4.4.
Dimensions in millimetres
0
27,s -02 12 +0,3
I-
I
I
C
l
----------
I
I I
I I
P
P,
I
0
In
I_
I
I
I
C C
I ----A---------- ------____ _I
r-
+I
!
0
4
I
Stroke---l
P Shoulder of lower clamp
C Centering line for test piece
- Apparatus: view from above
Figure 1
2

---------------------- Page: 10 ----------------------

SIST EN ISO 5981:1999
IS0 5981:1997(E)
Dimensions in millimetres
t--p= /- foot
Figure 2 - Apparatus: cross-section
4.2 Dimensions and characteristics
The machine shall have the following dimensions and characteristics:
a) distance between clamps: 12 mm
...