iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 15908:2010

(Main)

Anaesthetic and respiratory equipment - Non-interchangeable screw-threaded (NIST) low-pressure connectors for medical gases

Anaesthetic and respiratory equipment - Non-interchangeable screw-threaded (NIST) low-pressure connectors for medical gases

1.1   This European Standard specifies requirements for connectors intended for use with medical gases.
1.2   This European Standard specifies the dimensions and the allocation of non-interchangeable screw-threaded (NIST) connectors intended to be used at nominal operating pressures not greater than 1 400 kPa.
NOTE   As stated in EN ISO 5359, gas-specific quick-connectors conforming to EN ISO 9170-1 are considered as an alternative to NIST connectors.
1.3   The information to be supplied by the manufacturer is excluded from the scope of this European Standard because information about the use of NIST connectors is supplied by the manufacturer of each medical device to which the connectors are permanently fitted.

Anästhesie- und Beatmungsgeräte - Nichtverwechselbare Verbindungsstücke mit Schraubgewinde (NIST) für niedrigen Druck zur Verwendung mit medizinischen Gasen

1.1   Diese Europäische Norm legt die Anforderungen an Verbindungsstücke zur Verwendung mit medizinischen Gasen fest.
1.2   Diese Europäische Norm legt die Maße und die Zuordnung von nichtverwechselbaren Verbindungsstücken mit Schraubgewinde (NIST) fest, die zur Verwendung bei einem Nenn-Betriebsdruck von nicht mehr als 1 400 kPa vorgesehen sind.
ANMERKUNG   Wie in EN ISO 5359 angegeben, werden gasartspezifische Schnellverbindungsstücke nach EN ISO 9170-1 als Alternative zu NIST-Verbindungsstücken angesehen.
1.3   Die Informationen des Herstellers sind nicht Gegenstand dieser Europäischen Norm, da Informationen über die Anwendung von NIST-Verbindungsstücken vom Hersteller jedes medizinischen Gerätes bereitgestellt werden, an das die Verbindungsstücke fest angebracht sind.

Matériel respiratoire et anesthésique - Raccords basse pression à tête filetée non interchangeables (NIST) pour gaz médicaux

1.1 La présente Norme européenne spécifie les exigences requises pour les raccords destinés à être
utilisés avec les gaz médicaux.
1.2 La présente Norme européenne spécifie les dimensions et l’affectation des raccords à tête filetée non
interchangeables (NIST) destinés à être utilisés sous des pressions nominales de service inférieures ou
égales à 1400 kPa.
NOTE Comme indiqué dans l’EN ISO 5359, les raccords de prise rapide spécifiques à un gaz conformes à
l’EN ISO 9170-1 sont considérés comme une alternative aux raccords NIST.
1.3 Les informations à fournir par le fabricant sont exclues du domaine d’application de la présente Norme
européenne car les informations sur l’utilisation des raccords NIST sont fournies par le fabricant de chaque
appareil médical auquel les raccords sont fixés de manière permanente.

Anestezijska in dihalna oprema - Nizkotlačni priključki z navojem, ki se ne menjajo (NIST)

Ta evropski standard določa zahteve za priključke, namenjene za uporabo pri medicinskih plinih. Ta evropski standard določa mere in dodeljevanje priključkov z navojem, ki se ne menjajo (NIST), namenjenim za uporabo pri nazivnih obratovalnih tlakih, ki ne presegajo 1400 kPa. Informacije, ki jih priskrbi proizvajalec, so izključene iz področja uporabe tega evropskega standarda, ker informacije o uporabi NIST priključkov priskrbi proizvajalec vsake medicinske naprave, na katero so priključki stalno nameščeni.

General Information

Status
Withdrawn
Publication Date
05-Oct-2010
Withdrawal Date
17-Jun-2014
ICS
11.040.10 - Anaesthetic, respiratory and reanimation equipment
Technical Committee
CEN/TC 215 - Respiratory and anaesthetic equipment
Drafting Committee
CEN/TC 215/WG 3 - Medical gas supply systems
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
18-Jun-2014
Directive
2007/47/EC - Directive 2007/47/EC of the European Parliament and of the council of 5 September 2007 amending Council Directive 90/385/EEC on the approximation of the laws of the Member States relating to active implantable medical devices, Council Directive 93/42/EEC concerning medical devices and Directive 98/8/EC concerning the placing of biocidal products on the market
93/42/EEC - Council Directive 93/42/EEC of 14 June 1993 concerning medical devices
Mandate
M/023 - Standardization mandate to CEN/CENELEC concerning the development of European standards relating to medical devices
Ref Project
SIST EN 15908:2010 - Anaesthetic and respiratory equipment - Non-interchangeable screw-threaded (NIST) low-pressure connectors for medical gases

Relations

Replaced By
EN ISO 18082:2014 - Anaesthetic and respiratory equipment - Dimensions of non-interchangeable screw-threaded (NIST) low-pressure connectors for medical gases (ISO 18082:2014)
Effective Date
15-Feb-2012

Buy Standard

EN 15908:2010EN 15908:2010
PreviousNext
Standard
EN 15908:2010
English language
18 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.1,67Anästhesie- und Beatmungsgeräte - Nichtverwechselbare Verbindungsstücke mit Schraubgewinde (NIST) für niedrigen DruckMatériel respiratoire et anesthésique - Raccords à tête filetée non interchangeables (NIST) à basse pression pour gaz médicauxAnaesthetic and respiratory equipment - Non-interchangeable screw-threaded (NIST) low-pressure connectors for medical gases11.040.10Anestezijska, respiratorna in reanimacijska opremaAnaesthetic, respiratory and reanimation equipmentICS:Ta slovenski standard je istoveten z:EN 15908:2010SIST EN 15908:2010en,fr,de01-december-2010SIST EN 15908:2010SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 15908
October 2010 ICS 11.040.10 English Version
Anaesthetic and respiratory equipment - Non-interchangeable screw-threaded (NIST) low-pressure connectors for medical gases
Matériel respiratoire et anesthésique - Raccords basse pression à tête filetée non interchangeables (NIST) pour gaz médicaux
Anästhesie- und Beatmungsgeräte - Nichtverwechselbare Verbindungsstücke mit Schraubgewinde (NIST) für niedrigen Druck zur Verwendung mit medizinischen GasenThis European Standard was approved by CEN on 28 August 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 15908:2010: ESIST EN 15908:2010

FprEN 15908:2010 (E) 2 Contents Page Foreword .3Introduction .41Scope .52Normative references .53Terms and definitions .54General requirements .54.1Safety .54.2Materials .64.3Design, dimensions and allocation of NIST connectors .65Marking . 146Test for durability of markings . 14Annex A (informative)
Environmental aspects . 16Annex ZA (informative)
Relationship between this European Standard and the Essential Requirements of EU Directive 93/42/EEC Medical devices . 17Bibliography . 18
EN ISO 5359:2008. The requirements for NIST connectors in EN 15908 are identical to those currently given in EN ISO 5359:2008 except for:  the allocation of connector B11 (allocated to carbon dioxide instead to carbon dioxide/oxygen mixture [CO2 > 7 % (volume fraction)]);  the allocation of connector C 19 (allocated to carbon dioxide/oxygen mixture [CO2 > 7 % (volume fraction)] instead to carbon dioxide). It is intended that EN ISO 5359:2008 will be revised so as to delete the requirements for NIST connectors. The requirements for NIST connectors in EN 15908 are identical to those given in EN 739:1998 (cancelled and replaced by EN ISO 5359:2008) except for:  the allocations of connectors B11 (allocated to carbon dioxide only);  the allocation of connector C19 (allocated to carbon dioxide/oxygen mixture [CO2 > 7 % (volume fraction)] only);  the allocation of connector B12 to oxygen-enriched air;  the allocation of connector B15 to helium/oxygen mixture [O2 < 20 % (volume fraction)] only;  the allocation of connector C20 to helium only. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 18562-3:2024(Main)
Biocompatibility evaluation of breathing gas pathways in healthcare applications - Part 3: Tests for emissions of volatile organic substances (ISO 18562-3:2024)
SIST EN ISO 18562-3:2024

This document specifies tests for the emissions of volatile organic substances from the gas pathways of a medical device, its parts or accessories, which are intended to provide respiratory care or supply substances via the respiratory tract to a patient in all environments. The tests of this document are intended to quantify emissions of volatile organic substances that are added to the respirable gas stream by the materials of the gas pathway. This document establishes acceptance criteria for these tests.
NOTE            Gaseous emission of volatile organic substances includes emissions of volatile organic compounds, semi-volatile organic compounds and very volatile organic compounds.
This document addresses potential contamination of the gas stream arising from the gas pathways of medical devices or accessories, which is then conducted to the patient.
This document applies over the expected lifetime of the medical device in normal use and takes into account the effects of any intended processing.
This document does not address biological evaluation of the surfaces of gas pathways that are in direct contact with the patient. The requirements for direct contact surfaces are found in the ISO 10993 series.
Medical devices, parts or accessories containing gas pathways that are addressed by this document include, but are not limited to, ventilators, anaesthesia workstations (including gas mixers), breathing systems, oxygen conserving devices, oxygen concentrators, nebulizers, low-pressure hose assemblies, humidifiers, heat and moisture exchangers, respiratory gas monitors, respiration monitors, masks, medical respiratory personal protective equipment, mouth pieces, resuscitators, breathing tubes, breathing systems filters, Y-pieces and any breathing accessories intended to be used with such devices. The enclosed chamber of an incubator, including the mattress, and the inner surface of an oxygen hood are considered to be gas pathways and are also addressed by this document.
This document does not address contamination already present in the gas supplied from the gas sources while medical devices are in normal use.
EXAMPLE            Contamination arriving at the medical device from gas sources such as medical gas pipeline systems (including the non-return valves in the pipeline outlets), outlets of pressure regulators connected or integral to a medical gas cylinder or room air taken into the medical device is not addressed by ISO 18562 series.
This document is intended to be read in conjunction with ISO 18562-1.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 18562-2:2024(Main)
Biocompatibility evaluation of breathing gas pathways in healthcare applications - Part 2: Tests for emissions of particulate matter (ISO 18562-2:2024)
SIST EN ISO 18562-2:2024

This document specifies tests for the emissions of particulate matter from the gas pathways of a medical device, its parts or accessories, which are intended to provide respiratory care or supply substances via the respiratory tract to a patient in all environments. The tests of this document are intended to quantify particles from 0,25 µm diameter to 10 µm diameter that are emitted by the medical device, its parts or accessories into the respirable gas stream. This document establishes acceptance criteria for these tests.
This document does not address nanoparticles. Insufficient data exist to establish exposure limits for particles less than 0,25 µm diameter.
This document does not address particles larger than 10 µm diameter. These particles are deposited in the nasal cavity. Additional information can be needed for medical devices or accessories that bypass the nose. This is outside the scope of this document but can be required by some authorities having jurisdiction.
This document therefore adopts the same approach as the US Environmental Protection Agency (EPA) in setting limits based solely on particle size and not their chemistry.
This document addresses potential contamination of the gas stream arising from the gas pathways, which is then conducted to the patient.
This document applies over the expected lifetime of the medical device in normal use and takes into account the effects of any intended processing.
This document does not address biological evaluation of the particles that are deliberately released by a nebulizer (i.e. the therapeutic agent).
This document does not address biological evaluation of the surfaces of gas pathways that have direct contact with the patient. The requirements for direct contact surfaces are found in the ISO 10993 series.
Medical devices, parts or accessories, containing gas pathways that are addressed by this document, include, but are not limited to, ventilators, anaesthesia workstations (including gas mixers), breathing systems, oxygen conserving devices, oxygen concentrators, nebulizers, low-pressure hose assemblies, humidifiers, heat and moisture exchangers, respiratory gas monitors, respiration monitors, masks, medical respiratory personal protective equipment, mouth pieces, resuscitators, breathing tubes, breathing systems filters, Y-pieces, and any breathing accessories intended to be used with such devices. The enclosed chamber of an incubator, including the mattress, and the inner surface of an oxygen hood are considered to be gas pathways and are also addressed by this document.
This document does not address contamination already present in the gas supplied from the gas sources while medical devices are in normal use.
EXAMPLE            Contamination arriving at the medical device from gas sources such as medical gas pipeline systems (including the non-return valves in the pipeline outlets), outlets of pressure regulators connected or integral to a medical gas cylinder or room air taken into the medical device is not addressed by ISO 18562 (all parts).

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 18562-1:2024(Main)
Biocompatibility evaluation of breathing gas pathways in healthcare applications - Part 1: Evaluation and testing within a risk management process (ISO 18562-1:2024)
SIST EN ISO 18562-1:2024

This document specifies:
—     the general principles governing the biological evaluation within a risk management process of the gas pathways of a medical device, its parts or accessories, which are intended to provide respiratory care or supply substances via the respiratory tract to a patient in all environments;
—     the general categorization of gas pathways based on the nature and duration of their contact with the gas stream;
—     the evaluation of existing relevant data from all sources;
—     the identification of gaps in the available data set on the basis of a risk analysis;
—     the identification of additional data sets necessary to analyse the biological safety of the gas pathway;
—     the assessment of the biological safety of the gas pathway.
This document covers general principles regarding biocompatibility assessment of medical device materials, which make up the gas pathway, in normal use and normal condition. This document does not cover biological hazards arising from mechanical damage.
The other parts of ISO 18562 cover specific tests that address potentially hazardous substances that are added to the respirable gas stream and establish acceptance criteria for these substances.
This document addresses potential contamination of the gas stream arising from the gas pathways within the medical device, which might then be conducted to the patient.
This document applies over the expected lifetime of the medical device when operated according to the instructions for use. This includes degradation arising from exposure to environmental conditions as well as cleaning, disinfection and sterilisation (i.e. processing). It also includes user action or inaction (omission) that leads to an unintended or unexpected outcome (result) (i.e. use error). It does not include conscious/intentional action or inaction that violates the instructions for use and is beyond reasonable risk control by the manufacturer (i.e. abnormal use).
This document does not address biological evaluation of the surfaces of medical devices that have direct contact with the patient or user. The requirements for direct contact surfaces are found in the ISO 10993 series.
Medical devices, parts or accessories containing gas pathways that are addressed by this document include, but are not limited to, ventilators, anaesthesia workstations (including gas mixers), breathing systems, oxygen conserving equipment, oxygen concentrators, nebulizers, low-pressure hose assemblies, humidifiers, heat and moisture exchangers, respiratory gas monitors, respiration monitors, masks, medical respiratory personal protective equipment, mouth pieces, resuscitators, breathing tubes, breathing system filters and Y-pieces as well as any breathing accessories intended to be used with such medical devices. The enclosed chamber of an incubator, including the mattress, and the inner surface of an oxygen hood are considered to be gas pathways and are also addressed by this document.
This document does not address contamination already present in the gas supplied from the gas sources while medical devices are in normal use.
EXAMPLE            Contamination arriving at the medical device from gas sources such as medical gas pipeline systems (including the non-return valves in the pipeline outlets), outlets of pressure regulators connected or integral to a medical gas cylinder, or room air taken into the medical device is not addressed by ISO 18562 (all parts).

  • Standard
    49 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 18562-4:2024(Main)
Biocompatibility evaluation of breathing gas pathways in healthcare applications - Part 4: Tests for leachables in condensate (ISO 18562-4:2024)
SIST EN ISO 18562-4:2024

This document specifies tests for substances leached by liquid water condensing in gas pathways of a medical device, its parts or accessories, which are intended to provide respiratory care or supply substances via the respiratory tract to a patient in all environments. The chemical characterization methods described in this document apply to chemical substances that could leach from the medical device, its parts or accessories into the condensate. This document establishes verifiable acceptance criteria for these tests. The identity and quantity of each chemical released is intended for toxicological risk assessment as described in ISO 18562-1:2024.
This document addresses potential contamination of the gas stream arising from the gas pathways, which deliver breathing gas to the patient.
This document applies over the expected lifetime of the medical device in normal use and takes into account the effects of any intended processing.
This document does not address biological evaluation of the surfaces of gas pathways that have direct contact with the patient. The requirements for direct contact surfaces are found in the ISO 10993 series.
Medical devices, parts or accessories containing gas pathways that are addressed by this document include, but are not limited to, ventilators, anaesthesia workstations (including gas mixers), breathing systems, oxygen conserving devices, oxygen concentrators, nebulizers, low-pressure hose assemblies, humidifiers, heat and moisture exchangers, respiratory gas monitors, respiration monitors, masks, medical respiratory personal protective equipment, mouth pieces, resuscitators, breathing tubes, breathing systems filters, Y-pieces and any breathing accessories intended to be used with such devices. The enclosed chamber of an incubator, including the mattress, and the inner surface of an oxygen hood are considered to be gas pathways and are also addressed by this document.
This document does not address contamination already present in the gas supplied from the gas sources while medical devices are in normal use.
EXAMPLE            Contamination arriving at the medical device from gas sources such as medical gas pipeline systems (including the non-return valves in the pipeline outlets), outlets of pressure regulators connected or integral to a medical gas cylinder, or room air taken into the medical device.
This document does not address contact with drugs or anaesthetic agents. If a medical device or accessory is intended to be used with anaesthetic agents or drugs, then additional testing can be required. This document is intended to quantify hazardous water-soluble substances that are leached from the medical device, its parts or accessories by condensate and then conveyed by that liquid to the patient.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 80601-2-80:2024(Main)
Medical electrical equipment - Part 2-80: Particular requirements for basic safety and essential performance of ventilatory support equipment for ventilatory insufficiency (ISO 80601-2-80:2024)
SIST EN ISO 80601-2-80:2024

NOTE 1       There is guidance or rationale for this subclause contained in Clause AA.2.
This document applies to the basic safety and essential performance of ventilatory support equipment, as defined in 201.3.302, for ventilatory insufficiency, as defined in 201.3.302, hereafter also referred to as ME equipment, in combination with its accessories:
—    intended for use in the home healthcare environment;
NOTE 2     In the home healthcare environment, the supply mains driving the ventilatory support equipment is often not reliable.
NOTE 3     Such ventilatory support equipment can also be used in professional health care facilities.
—    intended for use by a lay operator;
—    intended for use with patients who have ventilatory insufficiency or failure, the most fragile of which would likely experience injury with the loss of this artificial ventilation;
—    intended for transit-operable use; and
—    not intended for patients who are dependent on artificial ventilation for their immediate life support.
EXAMPLE 1        Patients with moderate to severe chronic obstructive pulmonary disease (COPD), moderate amyotrophic lateral sclerosis (ALS), severe bronchopulmonary dysplasia or muscular dystrophy.
Ventilatory support equipment is not considered to use a physiologic closed-loop control system unless it uses a physiological patient variable to adjust the artificial ventilation therapy settings.
This document is also applicable to those accessories intended by their manufacturer to be connected to the ventilator breathing system of ventilatory support equipment for ventilatory insufficiency, where the characteristics of those accessories can affect the basic safety or essential performance of the ventilatory support equipment for ventilatory insufficiency.
EXAMPLE 2        Breathing sets, connectors, water traps, expiratory valve, humidifier, breathing system filter, external electrical power source, distributed alarm system.
If a clause or subclause is specifically intended to be applicable to ME equipment only, or to ME systems only, the title and content of that clause or subclause will say so. If that is not the case, the clause or subclause applies both to ME equipment and to ME systems, as relevant.
Hazards inherent in the intended physiological function of ME equipment or ME systems within the scope of this document are not covered by specific requirements in this document except in IEC 60601‑1:2005+AMD1:2012+AMD2:2020, 7.2.13 and 8.4.1.
NOTE 4       Additional information can be found in IEC 60601‑1:2005+AMD1:2012+AMD2:2020, 4.2.
NOTE 5       See ISO/TR 21954 for guidance on the selection of the appropriate ventilator for a given patient. 
This document does not specify the requirements for:
—    ventilators or accessories for ventilator-dependent patients intended for critical care applications, which are given in ISO 80601‑2‑12;
—    ventilators or accessories intended for anaesthetic applications, which are given in ISO 80601‑2‑13;
—    ventilators or accessories intended for the emergency medical services environment, which are given in ISO 80601‑2‑84;
—    ventilators or accessories intended for ventilator-dependent patients in the home healthcare environment, which are given in ISO 80601‑2‑72;
—    ventilatory support equipment or accessories intended for ventilatory impairment, which are given in ISO 80601‑2‑79;
—    sleep apnoea therapy ME equipment, which are given in ISO 80601‑2‑70;
—    high-frequency jet ventilato

  • Standard
    131 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 80601-2-79:2024(Main)
Medical electrical equipment - Part 2-79: Particular requirements for basic safety and essential performance of ventilatory support equipment for ventilatory impairment (ISO 80601-2-79:2024)
SIST EN ISO 80601-2-79:2024

NOTE 1       There is guidance or rationale for this subclause contained in Clause AA.2.
This document applies to the basic safety and essential performance of ventilatory support equipment, as defined in 201.3.302, for ventilatory impairment, as defined in 201.3.300, hereafter also referred to as ME equipment, in combination with its accessories:
—    intended for use in the home healthcare environment;
NOTE 2       In the home healthcare environment, the supply mains driving the ventilatory support equipment is often not reliable.
NOTE 3       Such ventilatory support equipment can also be used in professional health care facilities.
—    intended for use by a lay operator;
—    intended for use with patients who have ventilatory impairment, the most fragile of these patients, would not likely experience injury with the loss of this artificial ventilation; and
—    not intended for patients who are dependent on artificial ventilation for their immediate life support.
EXAMPLE 1        Patients with mild to moderate chronic obstructive pulmonary disease (COPD).
Ventilatory support equipment is not considered to use a physiologic closed-loop control system unless it uses a physiological patient variable to adjust the artificial ventilation therapy settings.
This document is also applicable to those accessories intended by their manufacturer to be connected to the breathing system of ventilatory support equipment for ventilatory impairment, where the characteristics of those accessories can affect the basic safety or essential performance of the ventilatory support equipment for ventilatory impairment.
EXAMPLE 2        Breathing sets, connectors, water traps, expiratory valve, humidifier, breathing system filter, external electrical power source, distributed alarm system.
If a clause or subclause is specifically intended to be applicable to ME equipment only, or to ME systems only, the title and content of that clause or subclause will say so. If that is not the case, the clause or subclause applies both to ME equipment and to ME systems, as relevant.
Hazards inherent in the intended physiological function of ME equipment or ME systems within the scope of this document are not covered by specific requirements in this document except in IEC 60601‑1:2005+AMD1:2012+AMD2:2020, 7.2.13 and 8.4.1.
NOTE 4       Additional information can be found in IEC 60601‑1:2005+AMD1:2012+AMD2:2020, 4.2.
NOTE 5       See ISO/TR 21954 for guidance on the selection of the appropriate ventilator for a given patient. 
This document does not specify the requirements for:
—    ventilators or accessories for ventilator-dependent patients intended for critical care applications, which are given in ISO 80601‑2‑12;
—    ventilators or accessories intended for anaesthetic applications, which are given in ISO 80601‑2‑13;
—    ventilators or accessories intended for the emergency medical services environment, which are given in ISO 80601‑2‑84;
—    ventilators or accessories intended for ventilator-dependent patients in the home healthcare environment, which are given in ISO 80601‑2‑72;
—    ventilatory support equipment or accessories intended for ventilatory insufficiency, which are given in ISO 80601‑2‑80;
—    sleep apnoea therapy ME equipment, which are given in ISO 80601‑2‑70;
—    high-frequency jet ventilators (HFJVs), which are given in ISO 80601‑2‑87;
—    high-frequency oscillatory ventilators (HFOVs);
—    respiratory high flow equipment, which are given in

  • Standard
    117 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 5362:2024(Main)
Anaesthetic and respiratory equipment - Anaesthetic reservoir bags (ISO 5362:2024)
SIST EN ISO 5362:2024

This document specifies requirements for anaesthetic reservoir bags for use with anaesthetic and ventilator breathing systems. It includes requirements for the design of the neck, size designation and elasticity.
This document is not applicable to special-purpose bags, for example bellows, self-inflating bags and bags for use with anaesthetic gas scavenging systems.
The requirements in this device-specific standard take precedence over any conflicting requirements in the general standard for airway devices (ISO 18190). All the common requirements that appear in the general standard for airway devices have been removed from this document.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 16571:2024(Main)
Systems for evacuation of plume generated by medical devices (ISO 16571:2024)
SIST EN ISO 16571:2024

This document specifies requirements and guidelines for systems and equipment used to evacuate plume generated by medical devices.
 This document applies to all types of plume evacuation systems (PESs), including
a)       portable;
b)       mobile;
c)        stationary, including dedicated central pipelines;
d)       PESs integrated into other equipment;
e)       PESs for endoscopic procedures (e.g., minimally invasive, laparoscopic)
This document applies to all healthcare facilities where PESs are used, including, but not limited to
a)       surgical facilities;
b)       medical offices;
c)        cosmetic treatment facilities;
d)       medical teaching facilities;
e)       dental clinics;
f)         veterinary facilities.
This document provides guidance on the following aspects of PESs:
a)       importance;
b)       purchasing;
c)        design;
d)       manufacture;
e)       documentation;
f)         function;
g)       performance;
h)       installation;
i)         commissioning;
j)         testing;
k)       training;
l)         use;
m)     risk assessment;
n)       servicing;
o)       maintenance.
This document does not apply to the following:
a)       anaesthetic gas scavenging systems (AGSSs) which are covered in ISO 7396-2;
b)       medical vacuum systems which are covered in ISO 7396-1;
c)        heating, ventilation, and air-conditioning (HVAC) systems;
d)       aspects of laser safety other than airborne contamination; and
e)       aspects of electrosurgery, electrocautery, and mechanical surgical tools other than airborne contamination produced by such equipment resulting from interaction with tissue or materials.

  • Standard
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 15002:2024(Main)
Flow control devices for connection to a medical gas supply system (ISO 15002:2023)
SIST EN ISO 15002:2024

This document specifies requirements for flow control devices that can be connected by the user either directly, by means of a probe or a gas-specific connector, or indirectly by means of a low-pressure hose assembly conforming with ISO 5359 to:
a)    a terminal unit conforming with ISO 9170-1 of a medical gas pipeline system conforming with ISO 7396-1:2016;
b)    the pressure outlet of a regulator conforming with ISO 10524-1:2018; or
c)    to the pressure outlet of a valve integrated pressure regulator (VIPR) conforming with ISO 10524-3 (see 5.2 gas inlets).
This document applies to the following types of flow control devices (FCDs):
a)    flowmeters;
b)    flowgauge FCDs; and
c)    fixed orifice FCDs.
NOTE       Flow control devices that are classed as medical electrical equipment can be subject to additional requirements of IEC 60601-1.
This document applies to flow control devices for the following gases:
—    oxygen;
—    oxygen 93 %;
—    nitrous oxide;
—    medical air;
—    carbon dioxide;
—    oxygen/nitrous oxide mixture 50/50 (% volume fraction);
—    oxygen-enriched air;
—    helium;
—    xenon; and
—    specified mixtures of the gases listed above.
NOTE Flow control devices can be available for other gases.
This document does not apply to flow control devices that are:
a)    for use with gases for driving surgical tools;
b)    an integral part of a regulator (see ISO 10524-1:2018); or
c)           an integral part of a valve with integrated pressure regulator (VIPR) (see ISO 10524-3).

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 80601-2-55:2018/A1:2023(Amendment)
Medical electrical equipment - Part 2-55: Particular requirements for the basic safety and essential performance of respiratory gas monitors - Amendment 1 (ISO 80601-2-55:2018/Amd 1:2023)
SIST EN ISO 80601-2-55:2018/A1:2024
  • Amendment
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day