prEN 12697-10
(Main)Bituminous mixtures - Test methods - Part 10: Compactability
Bituminous mixtures - Test methods - Part 10: Compactability
This document describes three test methods for characterizing the compactability of a bituminous mix, by the relation between its density or void content and the compaction energy applied to it, using an impact (Marshall) compactor, gyratory compactor, or a vibratory compactor.
This document applies to bituminous mixtures, both those prepared in laboratory and those resulting sampled from plant produced mixtures. The results of the test method serve to supplement the results of mixture design.
Asphalt - Prüfverfahren - Teil 10: Verdichtbarkeit
Dieses Dokument beschreibt drei Prüfverfahren zur Charakterisierung der Verdichtbarkeit von Asphal
ten durch das Verhältnis zwischen Dichte oder Luftporengehalt und der mittels eines Schlagverdichters (Marshall-Verdichter), Gyrator-Verdichters oder Vibrationsverdichters aufgebrachten Verdichtungsenergie.
Dieses Dokument gilt sowohl für im Labor als auch in der Asphaltmischanlage hergestellten Asphalt. Die Ergeb
nisse des Prüfverfahrens dienen zur Ergänzung der Ergebnisse aus der Konzeption des Gemischs.
Mélanges bitumineux - Méthodes d'essai - Partie 10 : Compactabilité
La présent document décrit trois méthodes d'essai permettant de caractériser la compactabilité d'un enrobé par la relation entre sa masse volumique apparente ou sa teneur en vides et l'énergie de compactage qui lui est appliquée à l'aide d'une machine de compactage par damage (Marshall), d'une presse à compactage giratoire ou d'un compacteur vibratoire.
La présente Norme européenne s'applique aux mélanges bitumineux confectionnés en laboratoire ou prélevés sur des mélanges produits en centrales. Les résultats de la méthode d'essai servent à compléter les résultats de l'épreuve de formulation.
Bitumenske zmesi - Preskusne metode - 10. del: Zgostljivost
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-marec-2025
Bitumenske zmesi - Preskusne metode - 10. del: Zgostljivost
Bituminous mixtures - Test methods - Part 10: Compactability
Asphalt - Prüfverfahren - Teil 10: Verdichtbarkeit
Mélanges bitumineux - Méthodes d'essai - Partie 10 : Compactabilité
Ta slovenski standard je istoveten z: prEN 12697-10
ICS:
93.080.20 Materiali za gradnjo cest Road construction materials
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT
EUROPEAN STANDARD
NORME EUROPÉENNE
EUROPÄISCHE NORM
January 2025
ICS 93.080.20 Will supersede EN 12697-10:2017
English Version
Bituminous mixtures - Test methods - Part 10:
Compactability
Mélanges bitumineux - Méthodes d'essai - Partie 10 : Asphalt - Prüfverfahren - Teil 10: Verdichtbarkeit
Compactabilité
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 227.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2025 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 12697-10:2025 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Principle . 5
5 Apparatus . 6
5.1 Impact compaction . 6
5.2 Gyratory compaction . 6
6 Test procedure . 6
6.1 Impact compaction . 6
6.1.1 Different specimens for each level of compaction energy, recording increases in
density . 6
6.1.2 One specimen for all levels of compaction energy, recording decreases in thickness 6
6.2 Gyratory compaction . 6
6.3 Vibratory compaction . 7
7 Calculation and expression of results . 7
7.1 Impact compaction . 7
7.1.1 Different specimens for each level of compaction energy, recording increases in
density . 7
7.1.2 Same specimen for all levels of compaction energy, recording decreases in thickness
..................................................................................................................................................................... 9
7.2 Gyratory compaction . 10
7.3 Vibratory compaction . 11
8 Test report . 11
9 Precision . 11
9.1 Impact compaction . 11
9.1.1 General. 11
9.1.2 One specimen for all levels of compaction energy, recording decreases in thickness
................................................................................................................................................................... 12
9.2 Gyratory compaction . 12
9.3 Vibratory compaction . 12
European foreword
This document (prEN 12697-10:2024) has been prepared by Technical Committee CEN/TC 227 “Road
materials”, the secretariat of which is held by BSI.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 12697-10:2017.
EN 12697-10:2017:
— [European Foreword] deletion of paragraph: “The applicability of this European Standard is
described in the product standards for bituminous materials.”;
— [Clause 2] the titles for test methods corrected by deletion of “for hot mix asphalt”;
— [5.1.2] amended to read: “mm with a maximum permissible error of 0,1 mm.”
— [5.1.3] amended to read: “Slide calliper rule, capable to measure the thickness of the specimen to
the nearest 0,1 mm with a maximum permissible error of 0,2 mm.”
— [6.1.2] 2nd paragraph clarified;
— [Clause 8] information to be included in the test report amended.
A list of all parts in the EN 12697 series can be found on the CEN website: www.cencenelec.eu
1 Scope
This document describes three test methods for characterizing the compactability of a bituminous mix,
by the relation between its density or void content and the compaction energy applied to it, using an
impact (Marshall) compactor, gyratory compactor, or a vibratory compactor.
This document applies to bituminous mixtures, both those prepared in laboratory and those resulting
sampled from plant produced mixtures. The results of the test method serve to supplement the results of
mixture design.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 12697-5, Bituminous mixtures — Test methods— Part 5: Determination of the maximum density
EN 12697-6, Bituminous mixtures — Test methods— Part 6: Determination of bulk density of bituminous
specimens
EN 12697-8, Bituminous mixtures — Test methods— Part 8: Determination of void characteristics of
bituminous specimens
EN 12697-30, Bituminous mixtures — Test methods— Part 30: Specimen preparation by impact compactor
EN 12697-31, Bituminous mixtures — Test methods— Part 31: Specimen preparation by gyratory
compactor
EN 12697-32, Bituminous mixtures — Test methods— Part 32: Laboratory compaction of bituminous
mixtures by vibratory compactor
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https://www.iso.org/obp/
— IEC Electropedia: available at https://www.electropedia.org/
3.1
compactability
K, k
ability of an asphalt mixture to be compacted (K when evaluated by gyratory compaction and k when
evaluated by vibratory compaction)
Note 1 to entry: High values of K and k will indicate a mixture for which less compaction energy is required to
obtain a given void content decrease.
3.2
compaction resistance
C, T
resistance of an asphalt mixture to being compacted (C when evaluated by impact compaction of several
specimens with varied compaction energy and T when evaluated by impact compaction of one specimen
while measuring its thickness)
Note 1 to entry: High values of C and T will indicate a mixture for which high compaction energy is required to
obtain a given void content decrease.
4 Principle
The bituminous mixture is compacted at a prescribed temperature with varying compaction energies
using one of three optional types of compaction methods:
a) impact compaction
b) gyratory compaction
c) vibratory compaction.
Two methods of monitoring the compactability can be applied:
— Method 1: two or more specimen are compacted with different amounts of compaction energy and
their densities are measured.
— Method 2: one specimen is used and its increase in density during the compaction process is
determined from its decrease in thickness.
The following Table 1 defines the compaction type to use depending of the compactness of tracking
method and gives the clause of test procedure.
Table 1 — Compaction type
Procedure clause according to
compaction method
impact gyratory vibratory
Compaction of specimens with carried compaction energy 6.1.1 n. a. 6.3
Measurement of specimen thickness during compaction 6.1.2 6.2 n. a.
A graph is drawn of density (or voids content) against compaction energy. When the impact compaction
is used, the compaction energy is characterized by the number of blows, when the gyratory compaction
is used, by the number of gyrations and when the vibratory compactor is used, by the duration in seconds.
A mathematical formula is derived from the experimental results, the parameters of which formula
characterize the compactability of the bituminous mixture.
5 Apparatus
5.1 Impact compaction
5.1.1 Marshall compactor shall be in accordance with EN 12697-30.
5.1.2 Measuring device for automatically recording the thickness of the specimen after each blow of
compaction with a maximum permissible error of 0,1 mm.
5.1.3 Slide calliper rule with a maximum permissible error of 0,1 mm.
5.2 Gyratory compaction
5.2.1 Gyratory compactor shall be in accordance with EN 12697-31.
5.3.1 Vibratory compactor shall be in accordance with EN 12697-32.
6 Test procedure
6.1 Impact compaction
6.1.1 Different specimens for each level of compaction energy, recording increases in density
For the determination of a single value of the compactability, prepare and compact Marshall specimen in
accordance with EN 12697-30 for each number of blows of compaction. The numbers of blows shall be
5, 15, 25, 35, 50 and 100 to each side of the specimen.
If required, determine the mass of bituminous mixture to be used in the specimen in order to achieve the
specimen thickness in accordance with EN 12697-30 by a preliminary compaction test.
The bulk density of the compacted specimens shall be determined in accordance with EN 12697-6.
6.1.2 One specimen for all levels of compaction energy, recording decreases in thickness
For the determination of a single value of compactability prepare and compact a Marshall specimen in
accordance with EN 12697-30 using 100 blows of compaction to each side.
In order to determine the required mass of bituminous mixture to achieve the specimen thickness in
accordance with EN 12697-30, a preliminary compaction test can be performed by using 100 blows to
each side of the specimen.
Measure the change in thickness of the specimen after each blow using the specified device according to
5.1.2.
Once the specimen has cooled to room temperature, take four measurements of its final thickness from
evenly spaced around the perimeter of the specimen by using the calliper as specified i
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.