EN 12697-2:2015/prA1

Bituminous mixtures - Test methods - Part 2: Determination of particle size distribution

This European Standard specifies a procedure for the determination of the particle size distribution of the aggregates of bituminous mixtures by sieving. The test is applicable to aggregates recovered after binder extraction in accordance with EN 12697-1 or EN 12697-39.
The applicability of this European Standard is described in the product standards for bituminous mixtures.
NOTE   Fibres, solid (non-soluble during extraction) additives and (some) binder modifiers influence the test result.

Asphalt - Prüfverfahren - Teil 2: Korngrößenverteilung

Diese Europäische Norm legt ein Verfahren für die Bestimmung der Korngrößenverteilung der Gesteinskör-nungen in Asphalt mittels Siebanalyse fest. Die Prüfung ist für Gesteinskörnungen, die nach Extraktion des Bindemittels nach EN 12697-1 oder EN 12697-39 rückgewonnen wurden, anwendbar.
Die Anwendbarkeit dieser Europäischen Norm ist in den Produktnormen für Asphalt beschrieben.
ANMERKUNG   Fasern, feste Zusatzstoffe (die bei der Extraktion nicht in Lösung gehen) und (einige) Modifizierungs-mittel für Bindemittel beeinflussen das Prüfergebnis.

Mélanges bitumineux - Méthode d'essai - Partie 2: Granulométrie

La présente Norme européenne spécifie un mode opératoire pour la détermination de la composition granulométrique des granulats dans les mélanges bitumineux, par tamisage. L'essai s'applique aux granulats récupérés après extraction du liant selon l'EN 12697-1 ou l'EN 12697-39.
L'applicabilité de la présente Norme européenne est décrite dans les normes de produits relatives aux mélanges bitumineux.
NOTE   Les fibres, additifs solides (non solubles durant l'extraction) et (certains) modificateurs de liants influencent le résultat de l'essai.

Bitumenske zmesi - Preskusne metode - 2. del: Ugotavljanje zrnavosti

General Information

• Status: Not Published
• ICS: 93.080.20 - Road construction materials
• Technical Committee: CEN/TC 227 - Road materials
• Drafting Committee: CEN/TC 227/WG 1 - Bituminous mixtures
• Ref Project: SIST EN 12697-2:2015/oprA1:2017 - Bituminous mixtures - Test methods - Part 2: Determination of particle size distribution

Relations

• Merged Into: EN 12697-2:2015+A1:2019 - Bituminous mixtures - Test methods - Part 2: Determination of particle size distribution
• Effective Date: 19-Jan-2023
• Amends: EN 12697-2:2015 - Bituminous mixtures - Test methods - Part 2: Determination of particle size distribution
• Effective Date: 12-Jul-2017

Standards Content (Sample)

SLOVENSKI STANDARD
01-december-2017
Bitumenske zmesi - Preskusne metode - 2. del: Ugotavljanje zrnavosti
Bituminous mixtures - Test methods - Part 2: Determination of particle size distribution
Asphalt - Prüfverfahren - Teil 2: Korngrößenverteilung
Mélanges bitumineux - Méthode d'essai - Partie 2: Granulométrie
Ta slovenski standard je istoveten z: EN 12697-2:2015/prA1
ICS:
93.080.20 Materiali za gradnjo cest Road construction materials
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

DRAFT
EUROPEAN STANDARD
EN 12697-2:2015
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
November 2017
ICS 93.080.20
English Version
Bituminous mixtures - Test methods - Part 2:
Determination of particle size distribution
Mélanges bitumineux - Méthode d'essai - Partie 2: Asphalt - Prüfverfahren - Teil 2: Korngrößenverteilung
Granulométrie
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 227.

This draft amendment A1, if approved, will modify the European Standard EN 12697-2:2015. If this draft becomes an
amendment, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for
inclusion of this amendment into the relevant national standard without any alteration.

This draft amendment was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turke
...