iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN ISO 11665-7:2015

(Main)

Measurement of radioactivity in the environment - Air: radon-222 - Part 7: Accumulation method for estimating surface exhalation rate (ISO 11665-7:2012)

Measurement of radioactivity in the environment - Air: radon-222 - Part 7: Accumulation method for estimating surface exhalation rate (ISO 11665-7:2012)

ISO 11665-7:2012 gives guidelines for estimating the radon-222 surface exhalation rate over a short period (a few hours), at a given place, at the interface of the medium (soil, rock, laid building material, walls, etc.) and the atmosphere. This estimation is based on measuring the radon activity concentration emanating from the surface under investigation and accumulated in a container of a known volume for a known duration.
This method is estimative only, as it is difficult to quantify the influence of many parameters in environmental conditions. ISO 11665-7:2012 is particularly applicable, however, in case of an investigation, a search for sources or a comparative study of exhalation rates at the same site. ISO 11665-7:2012 does not cover calibration conditions for the rate estimation devices.

Ermittlung der Radioaktivität in der Umwelt - Luft: Radon-222 - Teil 7: Anreicherungsverfahren zur Abschätzung der Oberflächenexhalationsrate (ISO 11665-7:2012)

Mesurage de la radioactivité dans l'environnement - Air: radon 222 - Partie 7: Méthode d'estimation du flux surfacique d'exhalation par la méthode d'accumulation (ISO 11665-7:2012)

L'ISO 11665-7:2012 donne des lignes directrices pour estimer le flux surfacique d'exhalation du radon 222 sur une courte période de temps (quelques heures), en un point donné, à l'interface entre un milieu (sol, roche, matériau de construction posé, mur, etc.) et l'atmosphère. Cette estimation est réalisée en mesurant l'activité volumique du radon exhalant de la surface étudiée et accumulé dans un conteneur de volume connu sur une période donnée.
Cette méthode n'est qu'estimative, car l'influence de nombreux paramètres est difficilement quantifiable dans les conditions environnementales. L'ISO 11665-7:2012 revêt cependant tout son intérêt dans le cas d'une investigation, d'une recherche de sources ou d'une étude comparative des flux d'exhalation sur un même site. L'ISO 11665-7:2012 ne traite pas des conditions d'étalonnage des dispositifs d'estimation du flux.

Merjenje radioaktivnosti v okolju - Zrak: radon-222 - 7. del: Akumulacijska metoda za ocenjevanje hitrosti površinskega izhajanja (ISO 11665-7:2012)

ISO 11665-7:2012 podaja smernice za ocenjevanje hitrosti površinskega izhajanja za radon-222 v kratkem obdobju (nekaj ur) na danem mestu pri stiku medija (zemlja, kamnine, položeni gradbeni material, stene itd.) z zrakom. Ta ocena temelji na izmerjeni koncentraciji aktivnosti radona, ki prehaja iz preiskovane površine in se nalaga v vsebniku znane prostornine v znanem časovnem okvirju. Ta metoda se uporablja samo za namene ocenjevanja, saj je kvantifikacija vpliva številnih parametrov v okoljskih pogojih težavna. Vendar se ISO 11665-7:2012 zlasti uporablja v primeru preiskave, iskanja virov ali primerjalne študije hitrosti izhajanja na istem mestu. ISO 11665-7:2012 ne obravnava pogojev kalibracije za naprave za ocenjevanje hitrosti.

General Information

Status
Published
Publication Date
15-Sep-2015
Withdrawal Date
30-Mar-2016
ICS
17.240 - Radiation measurements
Technical Committee
CEN/TC 430 - Nuclear energy, nuclear technologies, and radiological protection
Drafting Committee
CEN/TC 430 - Nuclear energy, nuclear technologies, and radiological protection
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
16-Sep-2015
Due Date
08-Sep-2016
Completion Date
16-Sep-2015
Ref Project
SIST EN ISO 11665-7:2015 - Measurement of radioactivity in the environment - Air: radon-222 - Part 7: Accumulation method for estimating surface exhalation rate (ISO 11665-7:2012)

Buy Standard

EN ISO 11665-7:2015EN ISO 11665-7:2015
PreviousNext
Standard
EN ISO 11665-7:2015
English language
31 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 11665-7:2015
01-november-2015
Merjenje radioaktivnosti v okolju - Zrak: radon-222 - 7. del: Akumulacijska metoda
za ocenjevanje hitrosti površinskega izhajanja (ISO 11665-7:2012)
Measurement of radioactivity in the environment - Air: radon-222 - Part 7: Accumulation
method for estimating surface exhalation rate (ISO 11665-7:2012)
Ermittlung der Radioaktivität in der Umwelt - Luft: Radon-222 - Teil 7:
Anreicherungsverfahren zur Abschätzung der Oberflächenexhalationsrate (ISO 11665-
7:2012)
Mesurage de la radioactivité dans l'environnement - Air: radon 222 - Partie 7: Méthode
d'estimation du flux surfacique d'exhalation par la méthode d'accumulation (ISO 11665-
7:2012)
Ta slovenski standard je istoveten z: EN ISO 11665-7:2015
ICS:
13.040.99 Drugi standardi v zvezi s Other standards related to air
kakovostjo zraka quality
17.240 Merjenje sevanja Radiation measurements
SIST EN ISO 11665-7:2015 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 11665-7:2015

---------------------- Page: 2 ----------------------

SIST EN ISO 11665-7:2015


EN ISO 11665-7
EUROPEAN STANDARD

NORME EUROPÉENNE

September 2015
EUROPÄISCHE NORM
ICS 17.240
English Version

Measurement of radioactivity in the environment - Air:
radon-222 - Part 7: Accumulation method for estimating
surface exhalation rate (ISO 11665-7:2012)
Mesurage de la radioactivité dans l'environnement - Ermittlung der Radioaktivität in der Umwelt - Luft:
Air: radon 222 - Partie 7: Méthode d'estimation du flux Radon-222 - Teil 7: Anreicherungsverfahren zur
surfacique d'exhalation par la méthode d'accumulation Abschätzung der Oberflächenexhalationsrate (ISO
(ISO 11665-7:2012) 11665-7:2012)
This European Standard was approved by CEN on 12 June 2015.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11665-7:2015 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 11665-7:2015
EN ISO 11665-7:2015 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 11665-7:2015
EN ISO 11665-7:2015 (E)
European foreword
The text of ISO 11665-7:2012 has been prepared by Technical Committee ISO/TC 85 “Nuclear energy,
nuclear technologies, and radiological protection” of the International Organization for Standardization
(ISO) and has been taken over as EN ISO 11665-7:2015 by Technical Committee CEN/TC 430 “Nuclear
energy, nuclear technologies, and radiological protection” the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2016, and conflicting national standards shall
be withdrawn at the latest by March 2016.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 18589-3:2024(Main)
Measurement of radioactivity in the environment - Soil - Part 3: Test method of gamma-emitting radionuclides using gamma-ray spectrometry (ISO 18589-3:2023, Corrected version 2023-11)
SIST EN ISO 18589-3:2024

This document specifies the identification and the measurement of the activity in soils of a large number of gamma-emitting radionuclides using gamma spectrometry. This non-destructive method, applicable to large-volume samples (up to about 3 l), covers the determination in a single measurement of all the γ-emitters present for which the photon energy is between 5 keV and 3 MeV.
Generic test method and fundamentals using gamma-ray spectrometry are described in ISO 20042.
This document can be applied by test laboratories performing routine radioactivity measurements as a majority of gamma-emitting radionuclides is characterized by gamma-ray emission between 40 keV and 2 MeV.
The method can be implemented using a germanium or other type of detector with a resolution better than 5 keV.
This document addresses methods and practices for determining gamma-emitting radionuclides activity present in soil, including rock from bedrock and ore, construction materials and products, pottery, etc. This includes such soils and material containing naturally occurring radioactive material (NORM) or those from technological processes involving Technologically Enhanced Naturally Occurring Radioactive Materials (TENORM) (e.g. the mining and processing of mineral sands or phosphate fertilizer production and use) as well as of sludge and sediment. This determination of gamma-emitting radionuclides activity is typically performed for the purpose of radiation protection. It is suitable for the surveillance of the environment and the inspection of a site and allows, in case of accidents, a quick evaluation of gamma activity of soil samples. This might concern soils from gardens, farmland, urban or industrial sites that can contain building materials rubble, as well as soil not affected by human activities.
When the radioactivity characterization of the unsieved material above 200 μm or 250 μm, made of petrographic nature or of anthropogenic origin such as building materials rubble, is required, this material can be crushed in order to obtain a homogeneous sample for testing as described in ISO 18589‑2.

  • Standard
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 19238:2023(Main)
Radiological protection - Performance criteria for service laboratories performing biological dosimetry by cytogenetics - Dicentric assay (ISO 19238:2023)
SIST EN ISO 19238:2023

This document provides criteria for quality assurance and quality control, evaluation of the performance and the accreditation of biological dosimetry by cytogenetic service laboratories using the dicentric assay performed with manual scoring.
This document is applicable to
a)    the confidentiality of personal information, for the requestor and the service laboratory,
b)    the laboratory safety requirements,
c)    the calibration sources and calibration dose ranges useful for establishing the reference dose-response curves that contribute to the dose estimation from unstable chromosome aberration frequency and the detection limit,
d)    the scoring procedure for unstable chromosome aberrations used for biological dosimetry,
e)    the criteria for converting a measured aberration frequency into an estimate of absorbed dose,
f)     the reporting of results,
g)    the quality assurance and quality control, and
h)    informative annexes containing sample instructions for requestor (see Annex A), sample questionnaire (see Annex B), sample report (see Annex C), fitting of the low dose-response curve by the method of maximum likelihood and calculating the error of the dose estimate (see Annex D), odds ratio method for cases of suspected exposure to a low dose (see Annex E), a method for determining the decision threshold and detection limit (see Annex F) and sample data sheet for recording aberrations (see Annex G).

  • Standard
    49 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 21909-2:2023(Main)
Passive neutron dosimetry systems - Part 2: Methodology and criteria for the qualification of personal dosimetry systems in workplaces (ISO 21909-2:2021)
SIST EN ISO 21909-2:2023

This document provides methodology and criteria to qualify the dosimetry system at workplaces where
it is used. The criteria in this document apply to dosimetry systems which do not meet the criteria with
regard to energy and direction dependent responses described in ISO 21909-1.
The qualification of the dosimetry system at workplace aims to demonstrate that:
— either, the non-conformity of the dosimetry system to some of the requirements on the energy or
direction dependent responses defined in ISO 21909-1 does not lead to significant discrepancies in
the dose determination for a certain workplace field;
— or, that the correction factor or function used for this specific studied workplace enables the
dosimetry system to accurately determine the conventional dose value with uncertainties similar
to the ones given in ISO 21909-1.
The methodologies to characterize the work place field in order to perform the qualification of the
dosimetry system are given in Annex A. Annex B is complementary as it gives the practical methods to
follow, once one methodology is chosen.
The provider of the dosimetry system shall provide the type test results corresponding to ISO 21909-1.
However, when the dosimetry system to be qualified does not comply with all the criteria of ISO 21909-1
dealing with the energy and angle dependence of the response, some tests of the ISO 21909-1 can be not
performed.

  • Standard
    40 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 8529-1:2023(Main)
Neutron reference radiations fields - Part 1: Characteristics and methods of production (ISO 8529-1:2021)
SIST EN ISO 8529-1:2023

This document specifies the neutron reference radiation fields, in the energy range from thermal up to 20 MeV, for calibrating neutron-measuring devices used for radiation protection purposes and for determining their response as a function of neutron energy.
This document is concerned only with the methods of producing and characterizing the neutron reference radiation fields.
The neutron reference radiation fields specified are the following:
—   neutron fields from radionuclide sources, including neutron fields from sources in a moderator;
—   neutron fields produced by nuclear reactions with charged particles from accelerators;
—   neutron fields from reactors.

  • Standard
    38 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 11929-4:2023(Main)
Determination of the characteristic limits (decision threshold, detection limit and limits of the coverage interval) for measurements of ionizing radiation - Fundamentals and application - Part 4: Guidelines to applications (ISO 11929-4:2022)
SIST EN ISO 11929-4:2023

This document specifies a procedure, in the field of ionizing radiation metrology, for the calculation of the “decision threshold”, the “detection limit” and the “limits of the coverage interval” for a non negative ionizing radiation measurand when counting measurements with preselection of time or counts are carried out. The measurand results from a gross count rate and a background count rate as well as from further quantities on the basis of a model of the evaluation. In particular, the measurand can be the net count rate as the difference of the gross count rate and the background count rate, or the net activity of a sample. It can also be influenced by calibration of the measuring system, by sample treatment and by other factors.
ISO 11929-4 gives guidance to the application of ISO 11929 (all parts), summarizing shortly the general procedure and then presenting a wide range of numerical examples. The examples cover elementary applications according to ISO 11929-1 and ISO 11929-2.

  • Standard
    107 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 23547:2023(Main)
Measurement of radioactivity - Gamma emitting radionuclides - Reference measurement standard specifications for the calibration of gamma-ray spectrometers (ISO 23547:2022)
SIST EN ISO 23547:2023

This document specifies the characteristics of solid, liquid or gas sources of gamma emitting
radionuclides used as reference measurement standards for the calibration of gamma-ray spectrometers.
These reference measurement standards are traceable to national measurement standards.
This document does not describe the procedures involved in the use of these reference measurement
standards for the calibration of gamma-ray spectrometers. Such procedures are specified in ISO 20042
and other documents.
This document specifies recommended reference radiations for the calibration of gamma-ray
spectrometers. This document covers, but is not restricted to, gamma emitters which emit photons in
the energy range of 60 keV to 1 836 keV. These reference radiations are realized in the form of point
sources or adequately extended sources specified in terms of activity which are traceable to national
standards.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 21909-1:2023(Main)
Passive neutron dosimetry systems - Part 1: Performance and test requirements for personal dosimetry (ISO 21909-1:2021)
SIST EN ISO 21909-1:2023

This document provides performance and test requirements for determining the acceptability of
neutron dosimetry systems to be used for the measurement of personal dose equivalent, Hp(10), for
neutrons ranging in energy from thermal to 20 MeV1).
This document applies to all passive neutron detectors that can be used within a personal dosemeter
in part or in all of the above-mentioned neutron energy range. No distinction between the different
techniques available in the marketplace is made in the description of the tests. Only generic distinctions,
for instance, as disposable or reusable dosemeters, are considered.
This document describes type tests only. Type tests are made to assess the basic characteristics of the
dosimetry systems and are often ensured by recognized national laboratories
This document does not present performance tests for characterizing the degradation induced by the
following:
— intrinsic temporal variability of the quality of the dosemeter supplied by the manufacturer;
— intrinsic temporal variability of preparation treatments (before irradiation and/or before reading),
if existing;
— intrinsic temporal variability of reading process;
— degradation due to environmental effects on the preparation treatments, if existing;
— degradation due to environmental effects on the reading process.

  • Standard
    53 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 20785-3:2023(Main)
Dosimetry for exposures to cosmic radiation in civilian aircraft - Part 3: Measurements at aviation altitudes (ISO 20785-3:2023)
SIST EN ISO 20785-3:2023

This document gives the basis for the measurement of ambient dose equivalent at flight altitudes for the evaluation of the exposures to cosmic radiation in civilian aircraft.

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 13304-1:2022(Main)
Radiological protection - Minimum criteria for electron paramagnetic resonance (EPR) spectroscopy for retrospective dosimetry of ionizing radiation - Part 1: General principles (ISO 13304-1:2020)
SIST EN ISO 13304-1:2023

The primary purpose of this document is to provide minimum acceptable criteria required to establish a procedure for retrospective dosimetry by electron paramagnetic resonance spectroscopy and to report the results.
The second purpose is to facilitate the comparison of measurements related to absorbed dose estimation obtained in different laboratories.
This document covers the determination of absorbed dose in the measured material. It does not cover the calculation of dose to organs or to the body. It covers measurements in both biological and inanimate samples, and specifically:
a)   based on inanimate environmental materials like glass, plastics, clothing fabrics, saccharides, etc., usually made at X-band microwave frequencies (8 GHz to 12 GHz);
b)   in vitro tooth enamel using concentrated enamel in a sample tube, usually employing X-band frequency, but higher frequencies are also being considered;
c)   in vivo tooth dosimetry, currently using L-band (1 GHz to 2 GHz), but higher frequencies are also being considered;
d)   in vitro nail dosimetry using nail clippings measured principally at X-band, but higher frequencies are also being considered;
e)   in vivo nail dosimetry with the measurements made at X-band on the intact finger or toe;
f)    in vitro measurements of bone, usually employing X-band frequency, but higher frequencies are also being considered.
For biological samples, in vitro measurements are carried out in samples after their removal from the person or animal and under laboratory conditions, whereas the measurements in vivo are carried out without sample removal and may take place under field conditions.
NOTE    The dose referred to in this document is the absorbed dose of ionizing radiation in the measured materials.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 8769:2022(Main)
Measurement of radioactivity - Alpha-, beta- and photon emitting radionuclides - Reference measurement standard specifications for the calibration of surface contamination monitors (ISO 8769:2020)
SIST EN ISO 8769:2023

This document specifies the characteristics of reference measurement standards of radioactive surface contamination, traceable to national measurement standards, for the calibration of surface contamination monitors. This document relates to alpha-emitters, beta-emitters, and photon emitters of maximum photon energy not greater than 1,5 MeV.
It does not describe the procedures involved in the use of these reference measurement standards for the calibration of surface contamination monitors. Such procedures are specified in IEC 60325[6], IEC 62363[7], and other documents.
NOTE    Since some of the proposed photon standards include filters, the photon standards are to be regarded as reference measurement standards of photons of a particular energy range and not as reference measurement standards of a particular radionuclide. For example, a 241Am source with the recommended filtration does not emit from the surface the alpha particles or characteristic low-energy L X-ray photons associated with the decay of the nuclide. It is designed to be a reference measurement standard that emits photons with an average energy of approximately 60 keV.
This document also specifies preferred reference radiations for the calibration of surface contamination monitors. These reference radiations are realized in the form of adequately characterized large area sources specified, without exception, in terms of surface emission rate and activity which are traceable to national standards.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day